Thanks guys,
The echo is there when T1 is connected directly to Asterisk box.
If connected to TNT first then to Asterisk via SIP, then Asterisk echo training kicks in (you can hear it 1st second or so) then only a little.
I haven't tried the steps below, but will when I build another box this next week.
Thanks,
James
On Fri, 1 Apr 2005 17:09:46 -0700, Damon Estep <[EMAIL PROTECTED]> wrote:
Brian,
By the description of James config there is no zaptel in hus box, looks like the TDM to SIP conversion is happening on the TNT, is it still your opinion that the steps below will help?
Taylor-----Original Message----- From: [EMAIL PROTECTED] [mailto:asterisk-users- [EMAIL PROTECTED] On Behalf Of Brian M. Arlinghaus Sent: Wednesday, March 23, 2005 2:16 PM To: Asterisk Users Mailing List - Non-Commercial Discussion; JamesRAMSubject: Re: [Asterisk-Users] echo paid support
James,
After three months of echo, I finally got mine to go away.
I am using a Dell Optiplex GX280 with a P4 3.2GHz processor and 512MBtrialand Asterisk version stable 1.07. Here's what I came up with after reading many of the posts and muchinand error.
1. Make sure that ther is no GUI loaded on the asterisk box.
2. Recompile Zaptel with MMX enabled (I think this applies to Intel Processors only, but someone may correct me if I'm wrong.)
To enable MMX in zaptel, before you compile zaptel, uncomment the linesupport./usr/src/zaptel/zconfig.h file that says: /* #define CONFIG_ZAPTEL_MMX */ and change it to: #define CONFIG_ZAPTEL_MMX
3. Recompile Zaptel with the "Aggressive Suppressor" enabled. I have never read anything about this, but saw it while I was enabling the MMX"MARK2">From reading zconfig.h, there are different versions of the echo canceller, but the comments say that the "aggressive suppressor" works withcompilewhich is what was enabled by default in stable 1.07.
To enable the MARK2 AGGRESSIVE SUPPRESSOR in zaptel, before youzaptel, uncomment the line in /usr/src/zaptel/zconfig.h file thatsays:what/* #define AGGRESSIVE_SUPPRESSOR */ and change it to: #define AGGRESSIVE_SUPPRESSOR
4. Recompile Zaptel with the instructions "reordered." I don't knowaddthis does, but it was recommended in these posts for fixing echo.
To "reorder" the instructions in zaptel, before you compile zaptel,looksthe following in /usr/src/zaptel/Makefile underneath the comment in the Makefile talking about all the config settings being in zconfig.h. From theInof it, it might only effect Pentium 4s???
CFLAGS+=-march=pentium4
5. Make sure the Zaptel card is not sharing an IRQ with othe hardware.my case, this involved moving my T100P to another slot and disablingallGX280USB ports. (I login remotely to administer the asterisk box since theIdoesn't have a PS/2 keyboard port.)
6. Make sure that you have a sufficient processor and sufficient RAM.didn't make any additions to my configuration, but I did remove one256MBwithRAM chip that seemed to be bad leaving 256MB.
Hope this helps. Again, most of this is not from me, but others hereknowsmuch more knowledge.
Brian Arlinghaus
----- Original Message ----- From: "James Taylor" <[EMAIL PROTECTED]> To: <asterisk-users@lists.digium.com> Sent: Thursday, March 17, 2005 10:40 AM Subject: [Asterisk-Users] echo paid support
> I've got echo problems. > *** I'm looking for paid support. *** > I'll accept free support, but don't mind paying if someone reallyPSTN->_T1->_MAX_TNT->_VOIP_G711->_ASTERISK_IAX_GSM->_ASTERISK_IAX_GSM-> what they are doing. > > > I've read the wiki, etc. > Played with the settings in zapata.conf > Using V400P > > PSTN->_T1->_ASTERISK->_BROADVOICE->_PSTN ECHO ON CALLED PHONE > PSTN->_T1->_ASTERISK->_T1->_PSTN NO ECHO > VOIP->_ASTERISK->_T1->_PSTN ECHO ON VOIP PHONE G711 > > I have another trunk group and different T1's that go to a MAX TNT first: > PSTN->_T1->_MAX_TNT->_VOIP->_ASTERISK->_VOIP_PHONE ECHO ON VOIP PHONE > g711 > >>_VOIP_PHONE_g711 > NO ECHO > -- > James Taylor > MetroTel > 3505 Summerihll Road > Suite 11 > Texarkana, Texas 75503 > 903-793-1956_______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
-- James Taylor MetroTel 3505 Summerihll Road Suite 11 Texarkana, Texas 75503 903-793-1956 _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users