Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??

Fri, 22 Apr 2005 20:10:23 -0700

I was wrong.  I just looked in my Mitel I&M's.  What level software are you on in the SX200?  Up until a certain level 200's could only do D4/AMI T1's, they could not do PRI's.  If it is a newer switch within the past 3 years or an older switch with later software than you can do PRI, but the signaling and framing must be ESF/B8ZS.
 
Henry
----- Original Message -----
Sent: Friday, April 22, 2005 7:04 PM
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??

 
 
Thanks,
  This is what I have now, but my Mitel PBX and Asterisk Box are unable to communicate via the T1 connection. Asterisk loads ok but I get error lights (blinking orange) on my TE110P and on my Mitel T1 card. Hummmm
 
 
-Scott
 
/etc/zaptel.conf
loadzone = us
defaultzone=us
span=1,0,0,d4,ami
bchan=1-23
dchan=24
 
/etc/asterisk/zapata.conf
[trunkgroups]
 
[channels]
context=default
switchtype=dms100
rxwink=300
usecallerid=no
hidecallerid=no
callwaiting=no
usecallingpres=yes
callwaitingcallerid=no
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0 ;into the pstn twords the telco
txgain=0.0
callgroup=1
pickupgroup=1
immediate=yes
 
signalling=pri_cpe
group=1
context=default 
emdigitwait=500
channel => 1-23 ; Set this to 1-15,17-31 for E1
 
 
----- Original Message -----
Sent: Friday, April 22, 2005 4:48 PM
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??

Hello Henry
e&m=1-23 should be bchan=1-23
you have it set for analog
also
signaling=pri_cpe


Henry Devito wrote:
Don't you need one of these directives so the PRI knows which is master and which is slave?
 
  • pri_cpe: PRI signaling, CPE side
  • pri_net: PRI signaling, Network side
    •  
    Henry
    ----- Original Message -----
    Sent: Friday, April 22, 2005 11:01 AM
    Subject: [Asterisk-Users] TE11OP -> Mitel 200Sx??

    Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows.

    Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.

    All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card.

    Any advice would be great.

    Zaptel.conf

    span=1,0,1,d4,ami

    e&m=1-23

    dchan=24

    Zapata.conf

    signalling=em_w

    switchtype=dms100

    echocancel=yes

    echocancelwhenbridged=yes

    echotraining=400

    callerid=asreceived

    group=1

    context=default

    channel => 1-23

    _______________________________________________
    Asterisk-Users mailing list
    [email protected]
    http://lists.digium.com/mailman/listinfo/asterisk-users
    To UNSUBSCRIBE or update options visit:
       http://lists.digium.com/mailman/listinfo/asterisk-users
    
_______________________________________________
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users

    _______________________________________________
    Asterisk-Users mailing list
    [email protected]
    http://lists.digium.com/mailman/listinfo/asterisk-users
    To UNSUBSCRIBE or update options visit:
       http://lists.digium.com/mailman/listinfo/asterisk-users

    _______________________________________________
    Asterisk-Users mailing list
    [email protected]
    http://lists.digium.com/mailman/listinfo/asterisk-users
    To UNSUBSCRIBE or update options visit:
       http://lists.digium.com/mailman/listinfo/asterisk-users
    _______________________________________________
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users

    Reply via email to