It liiks like a motherboard problem. It's failing the initial boot. You say it booted again after two hours. Was the machine powered down during that interval. If so, I suspect you have a temperature problem. I've seen very similar problems from a defective CPU fan.
Bill On 5/30/05, Ronald Wiplinger <[EMAIL PROTECTED]> wrote: > Yesterday my * server (SuSE 9.2 pro on Athlon) just stopped, no screen, > no reaction to keyboard or mouse. > > I get all kind of messages, or just stop during restart > > 1. just two lines of a code (immediately after turn on the computer) > 113-AM21200-100-GB > GV-RX30128D F1 > > > 2. Main Processor: AMD Athlon (tm) 64 Processor 3200+ > <CPUID: 0FF0 Patch ID: 0041> > > and BIOS line > 12/14/2004-NF-CK804-6A6IFG09C-00 > and it stops here > > > 3. No SATRaid found and it stops here > > > 4. ... No disk reserved for RAID use, RAID disable > (actually it meant computer disabled, and it stops here) > > 5. if I come to boot Linux, than it stops somewhere, with or without > kernel panic. > > The most I came was: > Excessive leakage detected on module 0:0 volts (00) after 162 ms > ProSLIC module failed leakage test. Check for short circuit > DC-DC cal has a surprising direct 107 of 0xff! > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > !!!!!!! DTMF_ROW_0_PEAK iREG 0 = FFFF should be 55C2 > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > !!!!!!! DTMF_ROW_1_PEAK iREG 1 = FFFF should be 51E6 > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > !!!!!!! DTMF_ROW_2_PEAK iREG 2 = FFFF should be 4B85 > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > !!!!!!! DTMF_ROW_3_PEAK iREG 3 = FFFF should be 4937 > ##### Loop error (ff) ##### > ##### Loop error (ff) ##### > !!!!!!! DTMF_ROW_1_PEAK iREG 4 = FFFF should be 3333 > CPU 0: Machine Check Exception: 4 Bank 4: b20000000000000070f0f > TSC 1cd4adfa6b > > Kernel panic - not syncing: Machine check > > Above error I googled as a problem in the Digium card. Chicken or egg? > Digium card or a result of another problem? Since I most of the time did > not come so far. > > Any idea? > > I can immagine from all the errors I saw: > 1. Motherboard is broken > 2. CPU is broken > 3. Power supply is broken (btw a very expensive one: 200 US$) > > What is your expert opinion??? Where and how to start to get back the > system stabled. Yes, after 2 hours it booted again, but I worry, that it > will happen anytime again. > > > > bye > > Ronald > > > _______________________________________________ > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
