Hey Chuck, You can set your callerid with any of our trunks since about 2 years ago. We modified some code in Asterisk to allow our border gateways with asterisk to transmit the callerid back to our telephone switch with the proper userid/accountid for billing reasons.
Thanks, Stephan Monette Unlimitel Inc. Tel.: 1-877-464-6638 Fax: (613) 482-1077 On 2011-02-15, at 9:29 AM, Chuck Mariotti wrote: > Are you transferring the inbound call to an external phone (via Unlimitel > Trunk) and trying to pass the inbound caller ID out to the receiving external > phone (so the user see's the original caller's ID)? > If so, I was under the impression that Unlimitel won't allow this unless you > have registered a static IP address with them. > > I would like to do the same. > -----Original Message----- > From: Henry Coleman [mailto:[email protected]] > Sent: February-15-11 8:08 AM > To: TAUG Technical > Subject: Fwd: [on-asterisk] End to End callerid > > ---------- Forwarded message ---------- > From: Henry Coleman <[email protected]> > Date: Tue, Feb 15, 2011 at 8:06 AM > Subject: Re: [on-asterisk] End to End callerid > To: Stephan Monette <[email protected]> > > > That's not the problem. > If I have an incoming call to an extension (DID) to Ext 200 and then call > forward this to an external number the call at that number displays the > Calling ID set by the extension or trunk not the original incoming call. > The same problem exists when transferring a call from an extension. ie. a > call comes from outside and displays the Caller ID but if the call is then > "blind" transfered the Caller ID is lost and the Caller ID is that of the > extension (if internal) not the original number. I think I need some code > that will preserve the original Caller ID after being transferred or > forwarded. > > Thx Henry Coleman > > > On Mon, Feb 14, 2011 at 5:45 PM, Stephan Monette <[email protected]>wrote: > >> You do not have to use any macros when using Unlimitel to send >> outgoing calls. It will use the incoming callerid information. >> >> Thanks, >> >> Stephan Monette >> Unlimitel Inc. >> >> Tel.: 1-877-464-6638 >> Fax: (613) 482-1077 >> >> >> >> >> >> On 2011-02-14, at 5:38 PM, Henry Coleman wrote: >> >> Is there a macro that I can use ? >> Henry >> >> >> On Mon, Feb 14, 2011 at 5:23 PM, Stephan Monette >> <[email protected]>wrote: >> >>> We do this all the time with Unlimitel. >>> >>> You can set your callerid for outgoing call with the incoming caller >>> ID info. >>> >>> Stephan Monette >>> Unlimitel Inc. >>> >>> Tel.: 1-877-464-6638 >>> Fax: (613) 482-1077 >>> >>> >>> >>> >>> >>> On 2011-02-14, at 5:21 PM, Henry Coleman wrote: >>> >>>> Hi all, I need to be able to call forward an incoming outside call >>>> and preserve the original CID to the end point. >>>> >>>> ie. Incoming Call+CalleridX ------------------->* >>>> Extension+C/F------------------>End Point+CalleridX >>>> >>>> Any ideas anyone ? >>>> >>>> -- >>>> *Henry L. Coleman * >>>> ***Per: VoIP-PBX.ca >>>> * >>>> * >>>> * >>> >>> >> >> >> -- >> *Henry L. Coleman * >> ***Per: VoIP-PBX.ca >> * >> * >> * >> >> >> >> >> >> >> > > > -- > *Henry L. Coleman * > ***Per: VoIP-PBX.ca > * > * > * > > > > > > > > > -- > *Henry L. Coleman * > ***Per: VoIP-PBX.ca > * > * > * > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [email protected] > For additional commands, e-mail: [email protected] > --------------------------------------------------------------------- To unsubscribe, e-mail: [email protected] For additional commands, e-mail: [email protected]
