Darryl, Tell your brother to try "sudo yum list \*m2crypto\*" to find packages that might satisfy this requirement.
And that applies to any other missing package. -Philip On 8/13/10 10:47 AM, Darryl Chandler wrote: > Thanks Darrick - I disabled the package. I am using the instructions on the > page you mentioned, but the toolchain/build step is where I'm getting stuck. > > I was able to install "autoconf" through yum, but now have this error, to > which I cannot find a package using yum: > > Script started, file is build.log_ > Host rpm missing: m2crypto > make: *** [host.rpm.m2crypto] Error 1 > Script done, file is build.log_ > > real 0m4.572s > user 0m3.089s > sys 0m1.368s > > > Is there a list of packages/dependencies that are required? I searched rpm > and m2crypto and couldn't find anything that wasn't already installed on the > PC. > > Thanks for the help.. > > -Darryl > > > > > -----Original Message----- > From: Darrick Hartman [mailto:dhart...@djhsolutions.com] > Sent: August 13, 2010 12:30 PM > To: AstLinux Users Mailing List > Subject: Re: [Astlinux-users] Asterisk 1.6 install > > PRI's have nothing to do with isdn. Two separate technologies. You can > turn off app-bundle and the misdn options and leave libpri enabled. > You'll have your pri support (depending on the card). > > HOST missing tool means you're missing the tool on your build system. > So, yes, you'll need to use yum to install that. > > The documentation on the website does explain most of this. (use make > menuconfig to turn packages on/off within the development environment). > > http://doc.astlinux.org/devdoc:documentation > > We do need to add additional notes to that page and probably could make > some of the error messages more verbose. The build system can take a > little bit of effort to understand, depending on your level of knowledge. > > Darrick > > > On 08/13/2010 09:56 AM, Darryl Chandler wrote: >> I would like to use PRIs in the future, but not at this exact moment is it >> necessary. I assume I would need to stick with asterisk 1.4 to use it at >> this time? >> >> When I do disable this bundle, I still get the error about " Host tool >> missing: autoconf".. Do I need to install another package (through yum) to >> resolve this? >> >> Thanks, >> >> >> >> -Darryl >> >> >> >> -----Original Message----- >> From: Darrick Hartman [mailto:dhart...@djhsolutions.com] >> Sent: August 13, 2010 10:38 AM >> To: AstLinux Users Mailing List >> Subject: Re: [Astlinux-users] Asterisk 1.6 install >> >> Darryl, >> >> app_bundle is a misdn thing. If you don't need ISDN support, you can >> disable that and a few other things. >> >> Darrick >> >> On 08/13/2010 09:11 AM, Darryl Chandler wrote: >>> I was following the steps for building astlinux from the SVN. I wanted >>> to use asterisk 1.6, so after "make oldconfig" I edited the .config >>> file, and made the following changes: >>> >>> # BR2_PACKAGE_ASTERISK_v1_4 is not set >>> >>> BR2_PACKAGE_ASTERISK_v1_6=y >>> >>> When I try toolchain/build though, I get the following errors: >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> Script started, file is build.log_ >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> package/app_bundle/app_bundle.mk:51: *** app_bundle is only compatible >>> with Asterisk 1.4.x. Stop. >>> >>> Script done, file is build.log_ >>> >>> real 0m1.283s >>> >>> user 0m0.793s >>> >>> sys 0m0.487s >>> >>> I can see where this option is in the .option file, but if I disable it, >>> will I lose asterisk applications? I did try disabling it, but got this >>> error when running toolchain/build: >>> >>> Script started, file is build.log_ >>> >>> Host tool missing: autoconf >>> >>> make: *** [host.autoconf] Error 1 >>> >>> Script done, file is build.log_ >>> >>> real 0m4.207s >>> >>> user 0m3.039s >>> >>> sys 0m1.159s >>> >>> I'd appreciate any help on getting this built with 1.6. >>> >>> Thanks! >>> >>> -Darryl >>> >>> >>> >>> ------------------------------------------------------------------------------ This SF.net email is sponsored by Make an app they can't live without Enter the BlackBerry Developer Challenge http://p.sf.net/sfu/RIM-dev2dev _______________________________________________ Astlinux-users mailing list Astlinux-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to pay...@krisk.org.
