Thankyou so much for this information. I do not want to use regulatory.db. Can you please share your ath10k build configuration? I may be missing something in configuration.
Thanks & Regards, Kavita On Wed, 13 Dec 2017 07:54:00 +0000, Manikanta Pubbisetty wrote > Please CC linux wireless when posting queries on cfg/mac80211. > > At least, I have not had any issues in interface bring up after the latest > regulatory.db change, I have tested it with vanilla ath.git and it worked > even > without regulatory.db file. If you may want to refer, Johannes submitted a > patch[1] for converting db.txt to firmware file format. > > [1] https://patchwork.kernel.org/patch/9992477/ > > mkp > > >-----Original Message----- > >From: ath10k [mailto:ath10k-boun...@lists.infradead.org] On Behalf Of > >KAVITA MATHUR > >Sent: Wednesday, December 13, 2017 12:02 PM > >To: ath10k@lists.infradead.org > >Subject: regulatory.db file for ath10k > > > >hi, > > > >wifi interface is not up with ath10k driver due to missing regulatory.db.I > >have > >taken ath10k latest driver code from backports and ath10k git on 12 Dec. > > > > > > > >Loading modules backported from Linux version v3.18-239930-g135da6d > >Backport generated by backports.git v4.14-rc2-1-35-g3d13478 ath10k_pci > >0002:03:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 > >cfg80211: failed to load regulatory.db > >ath10k_pci 0002:03:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff > >sub 0000:0000 ath10k_pci 0002:03:00.0: kconfig debug 0 debugfs 0 tracing 0 > >dfs > >0 testmode 0 ath10k_pci 0002:03:00.0: firmware ver 10.2.4.70.66 api 5 > >features > >no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 c2dd2ad5 ath10k_pci > >0002:03:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 ath10k_pci > >0002:03:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 > >hwcrypto > >1 > > > >wifi > >root@CDOT:/# IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready device > >wlan0 entered promiscuous mode device wlan0 left promiscuous mode > >br-lan: port 2(wlan0) entered disabled state > > > >How to generate regulatory.db file or is it available to use it directly? > >Please > >help me to fix it. > > > > > > > > > > > > > > > > > >Thanks & Regards, > >कविता माथुर Kavita Mathur > >वरिष्ठ अनुसंधान अभियंता Senior Research Engineer > >सी-डॉट C-DOT > >इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I > >होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100 > >फोन Ph 080-28529896 > >Disclaimer: > >---------- > >This email and any files transmitted with it > > > > > >_______________________________________________ > >ath10k mailing list > >ath10k@lists.infradead.org > >http://lists.infradead.org/mailman/listinfo/ath10k Thanks & Regards, कविता माथुर Kavita Mathur वरिष्ठ अनुसंधान अभियंता Senior Research Engineer सी-डॉट C-DOT इलैक्ट्रॉनिक्स सिटी फेज़ I Electronics City Phase I होसूर रोड, बेंगलूरु Hosur Road, Bengaluru – 560100 फोन Ph 080-28529896 Disclaimer: ---------- This email and any files transmitted with it _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k