Christian Lamparter <chunk...@gmail.com> writes:
> Many integrated QCA9984 WiFis in various IPQ806x platform routers
> from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
> etc.) have either blank, bogus or non-unique MAC-addresses in
> their calibration data.
>
> As a result, OpenWrt utilizes a discouraged binary calibration data
> patching method that allows to modify the device's MAC-addresses right
> at the source. This is because the ath10k' firmware extracts the MAC
> address from the supplied radio/calibration data and issues a response
> to the ath10k linux driver. Which was designed to take the main MAC in
> ath10k_wmi_event_ready().
>
> Part of the "setting an alternate MAC" issue was already tackled by a
> patch from Brian Norris:
> commit 9d5804662ce1
> ("ath10k: retrieve MAC address from system firmware if provided")
> by allowing the option to specify an alternate MAC-address with the
> established device_get_mac_address() function which extracts the right
> address from DeviceTree/fwnode mac-address or local-mac-address
> properties and saves it for later.
>
> However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
> to not properly calculate its rx-bssid mask in this case. This can cause
> issues in the popluar "multiple AP with a single ath10k instance"
> configurations.
>
> To improve MAC address handling, Felix Fietkau suggested to call
> pdev_set_base_macaddr_cmdid before bringing up the first vif and
> use the first vif MAC address there. Which is in ath10k_core_start().
>
> This patch implement Felix Fietkau's request to
> "call pdev_set_base_macaddr_cmdid before bringing up the first vif".
> The pdev_set_base_macaddr_cmdid is already declared for all devices
> and version. The driver just needed the support code for this
> function.
>
> BugLink:
> https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
> Fixes: 9d5804662ce1 ("ath10k: retrieve MAC address from system firmware if
> provided")
> Cc: Brian Norris <briannor...@chromium.org>
> Cc: Ben Greear <gree...@candelatech.com>
> Cc: Felix Fietkau <n...@nbd.name>
> Cc: Mathias Kresin <d...@kresin.me>
> Signed-off-by: Christian Lamparter <chunk...@gmail.com>
[...]
> --- a/drivers/net/wireless/ath/ath10k/core.c
> +++ b/drivers/net/wireless/ath/ath10k/core.c
> @@ -2649,6 +2649,13 @@ int ath10k_core_start(struct ath10k *ar, enum
> ath10k_firmware_mode mode,
> goto err_hif_stop;
> }
>
> + status = ath10k_wmi_pdev_set_base_macaddr(ar, ar->mac_addr);
> + if (status) {
> + ath10k_err(ar,
> + "failed to set base mac address: %d\n", status);
> + goto err_hif_stop;
> + }
Oh, and as the new parameter is not supported with WMI TLV interface
(QCA6174, WCN3990 etc) this will print an error on those. I think you
need to check for -EOPNOTSUPP and then just ignore the error on that
case. IIRC we have similar checks elsewhere in ath10k.
--
Kalle Valo
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
