Add support for the bluetooth part of the QCA6391 BT+WiFi chip present
on the RB5 board. WiFi is not supported yet, as it requires separate
handling of the PCIe device power.

Signed-off-by: Dmitry Baryshkov <dmitry.barysh...@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 50 ++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts 
b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index 8ac96f8e79d4..326330f528fc 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -19,6 +19,7 @@ / {
 
        aliases {
                serial0 = &uart12;
+               serial1 = &uart6;
                sdhc2 = &sdhc_2;
        };
 
@@ -98,6 +99,25 @@ lt9611_3v3: lt9611-3v3 {
                regulator-always-on;
        };
 
+       qca_pwrseq: qca-pwrseq {
+               compatible = "qcom,qca6390-pwrseq";
+
+               #pwrseq-cells = <1>;
+
+               vddaon-supply = <&vreg_s6a_0p95>;
+               vddpmu-supply = <&vreg_s2f_0p95>;
+               vddrfa1-supply = <&vreg_s2f_0p95>;
+               vddrfa2-supply = <&vreg_s8c_1p3>;
+               vddrfa3-supply = <&vreg_s5a_1p9>;
+               vddpcie1-supply = <&vreg_s8c_1p3>;
+               vddpcie2-supply = <&vreg_s5a_1p9>;
+               vddio-supply = <&vreg_s4a_1p8>;
+
+               bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+               wifi-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+               swctrl-gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>;
+       };
+
        thermal-zones {
                conn-thermal {
                        polling-delay-passive = <0>;
@@ -804,6 +824,26 @@ lt9611_rst_pin: lt9611-rst-pin {
        };
 };
 
+&qup_uart6_default {
+       ctsrx {
+               pins = "gpio16", "gpio19";
+               drive-strength = <2>;
+               bias-disable;
+       };
+
+       rts {
+               pins = "gpio17";
+               drive-strength = <2>;
+               bias-disable;
+       };
+
+       tx {
+               pins = "gpio18";
+               drive-strength = <2>;
+               bias-pull-up;
+       };
+};
+
 &qupv3_id_0 {
        status = "okay";
 };
@@ -1193,6 +1233,16 @@ sdc2_card_det_n: sd-card-det-n {
        };
 };
 
+&uart6 {
+       status = "okay";
+       bluetooth {
+               compatible = "qcom,qca6390-bt";
+               clocks = <&sleep_clk>;
+
+               bt-pwrseq = <&qca_pwrseq 1>;
+       };
+};
+
 &uart12 {
        status = "okay";
 };
-- 
2.33.0


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Reply via email to