Hello list, upon loading the ath9k module on the device, the system completely stalls and reboots with following output:
r...@openwrt:/# modprobe ath9k debug=0xffffffff ath9k 0000:00:11.0: failed to initialize device ath9k: probe of 0000:00:11.0 failed with error -22 ath9k 0000:00:12.0: failed to initialize device ath9k: probe of 0000:00:12.0 failed with error -22 Since it is running as a ramdisk image i cannot get any debug outputs after reboot. Hardware is 2.4GHz/5GHz AR9220 and 2.4GHz AR9223 radios (according to http://www.smallnetbuilder.com/content/view/30913/96/) and Atheros 9280 MAC (according to stock firmware). This is the related thread at the openWrt forum: https://forum.openwrt.org/viewtopic.php?id=22311 Since this router is router is not fully supported by openWrt it _may_ be possible there is a problem with the PCI bus. Could i check this somehow? Driver is from compat wireless 2009-08-20. More info: r...@openwrt:/# uname -a Linux OpenWrt 2.6.30.9 #60 Tue Nov 10 17:09:22 CET 2009 mips GNU/Linux r...@openwrt:/# lspci -n 00:00.0 0000: 0700:1107 (rev 01) 00:11.0 0280: 168c:0029 (rev 01) 00:12.0 0280: 168c:0029 (rev 01) r...@openwrt:/# lspci -vvv 00:11.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01) Subsystem: Atheros Communications Inc. Device a095 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 48 Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00:12.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01) Subsystem: Atheros Communications Inc. Device a094 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 49 Region 0: Memory at 10010000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Regards Marco _______________________________________________ ath9k-devel mailing list ath9k-devel@lists.ath9k.org https://lists.ath9k.org/mailman/listinfo/ath9k-devel