Hi Sujith,
Here is the info:
I am using compat-wireless-3.2-1-s
cat modal_eeprom
Chain0 Ant. Control : 16
Chain1 Ant. Control : 16
Ant. Common Control : 528
Chain0 Ant. Gain : 0
Chain1 Ant. Gain : 0
Switch Settle : 45
Chain0 TxRxAtten : 32
Chain1 TxRxAtten : 32
Chain0 RxTxMargin : 0
Chain1 RxTxMargin : 0
ADC Desired size : -30
txEndToXpaOff : 0
txEndToRxOn : 2
txFrameToXpaOn : 14
CCA Threshold) : 28
Chain0 NF Threshold : -1
Chain1 NF Threshold : -1
xpdGain : 2
External PD : 1
Chain0 I Coefficient : 0
Chain1 I Coefficient : 0
Chain0 Q Coefficient : 0
Chain1 Q Coefficient : 0
pdGainOverlap : 6
xPA Bias Level : 0
txFrameToDataStart : 14
txFrameToPaOn : 14
HT40 Power Inc. : 2
Chain0 bswAtten : 0
Chain1 bswAtten : 0
Chain0 bswMargin : 0
Chain1 bswMargin : 0
HT40 Switch Settle : 45
AR92x7 Version : 0
DriverBias1 : 3
DriverBias2 : 3
CCK OutputBias : 3
PSK OutputBias : 3
QAM OutputBias : 3
PAL_OFF OutputBias : 1
cat base_eeprom
Major Version : 14
Minor Version : 4
Checksum : 49857
Length : 1028
RegDomain1 : 32924
RegDomain2 : 31
TX Mask : 3
RX Mask : 3
Allow 5GHz : 0
Allow 2GHz : 1
Disable 2GHz HT20 : 0
Disable 2GHz HT40 : 0
Disable 5Ghz HT20 : 1
Disable 5Ghz HT40 : 1
Big Endian : 0
Cal Bin Major Ver : 0
Cal Bin Minor Ver : 8
Cal Bin Build : 127
Power Table Offset : -5dB
OpenLoop Power Ctrl : 1
MacAddress : f4:ec:38:0c:a4:9e
2012/1/11 Markus Kaindl <markus.kai...@stusta.de>
> I've got the same Problem with the same device used as a Access-Point
> with HostAPD. I will provide the Information you requested in a few days!
>
> Markus
>
> Sujith Manoharan schrieb:
> > Mulong Chen wrote:
> >> I am using ath9k_htc with my TL-WN821N. The problem is when it
> transfers with
> >> max speed (should be 300Mbps but not with ath9k_htc, this could be
> another
> >> story) for some while (eg. 10 mins), the dongle gets really hot and it
> hangs
> >> with no blinked LED. At this time, there is no response from the dongle
> >> anymore. I have to plug in/out to make it get normal.
> >>
> >> But everything under windows is just fine. With max speed (300 Mbps) do
> some
> >> ftp for 1 or 2 hours, everything is just fine.
> >>
> >> I am so sure that the hang is because of the chips getting too hot. I
> bought 2
> >> pieces of heat sink and attached them on the two chips. And the
> transftering
> >> lasted almost 1 hours till now (normal case it would die in 15 mins.),
> even
> >> the heat sink is really really hot.
> >>
> >>
> >> lsusb Bus 002 Device 006: ID 0cf3:7015 Atheros Communications, Inc.
> TP-Link
> >> TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
> >>
> >> kernel version Linux CC 3.1.8-1-ARCH
> >
> > Can you install the latest compat-wireless package from:
> > http://linuxwireless.org/en/users/Download ?
> >
> > Debugging has to be enabled by using these flags in config.mk:
> >
> > CONFIG_ATH9K_HTC_DEBUGFS=y
> > CONFIG_ATH_DEBUG=y
> >
> > For generic instructions, please see:
> > http://linuxwireless.org/en/users/Drivers/ath9k/debug
> >
> > And then, please post the output of:
> >
> > cat /sys/kernel/debug/ieee80211/phy#/ath9k_htc/modal_eeprom
> > cat /sys/kernel/debug/ieee80211/phy#/ath9k_htc/base_eeprom
> >
> > Sujith
> > _______________________________________________
> > ath9k-devel mailing list
> > ath9k-devel@lists.ath9k.org
> > https://lists.ath9k.org/mailman/listinfo/ath9k-devel
>
>
> _______________________________________________
> ath9k-devel mailing list
> ath9k-devel@lists.ath9k.org
> https://lists.ath9k.org/mailman/listinfo/ath9k-devel
>
>
_______________________________________________
ath9k-devel mailing list
ath9k-devel@lists.ath9k.org
https://lists.ath9k.org/mailman/listinfo/ath9k-devel
