Tip for all: use http://talk.mikrotik.com.au for this kind of topic :-}
> -----Original Message----- > From: AusNOG [mailto:ausnog-boun...@lists.ausnog.net] On Behalf Of Rhys > Cuff (Latrobe I.T) > Sent: Friday, 6 April 2018 1:00 PM > To: ausnog@lists.ausnog.net > Subject: Re: [AusNOG] CPU - when to upgrade > > Ohhhh setting a rule at the top to fasttrack established connections made a > huge difference. > Thanks for the tip > > > > -----Original Message----- > From: Mike Everest [mailto:m...@duxtel.com] > Sent: Friday, April 6, 2018 12:31 PM > To: Rhys Cuff (Latrobe I.T); ausnog@lists.ausnog.net > Subject: RE: [AusNOG] CPU - when to upgrade > > Hi Rys, > > With routerOS, throughput limitation due to cpu really only happens when it > completely runs out (i.e. 100% utilisation) - when you hit 100, router can't > keep up with incoming packets and so some packets begin to be dropped. > That can have a follow-on effect that TCP stream initiators will start to pare > back the transmit rate accordingly so if your router is CLOSE to 100% but not > quite, it can still indicate a throughput limit. But 70% - 80% is not > usually a > problem for throughput. > > Other actions as already suggested, like fastpath and/or review of firewall > rule order can make a huge difference - even adding a 'permit established' at > the top of the forward chain can make a massive difference if you don’t > already have it ;) > > Cheers! > > Mike. > > > -----Original Message----- > > From: AusNOG [mailto:ausnog-boun...@lists.ausnog.net] On Behalf Of > > Rhys Cuff (Latrobe I.T) > > Sent: Friday, 6 April 2018 11:44 AM > > To: ausnog@lists.ausnog.net > > Subject: Re: [AusNOG] CPU - when to upgrade > > > > Hi Guys > > > > Thanks very much for the responses. > > We are a very small wireless ISP (around 2000 customers) and run > > MikroTik router kit (I know I know...) I can see its normally firewall > > and routing process's that use most. > > Running around 300mbps on the routers in question. > > I can certainly upgrade, just wasn’t sure if it was worth it. > > MikroTik don’t have much kit that is small and runs 24v. > > > > Thanks again > > > > Rhys > > > > > > > > > > -----Original Message----- > > From: Graeme Allen [mailto:m...@graemeallen.com] > > Sent: Friday, April 6, 2018 11:22 AM > > To: Rhys Cuff (Latrobe I.T) > > Cc: ausnog@lists.ausnog.net > > Subject: Re: [AusNOG] CPU - when to upgrade > > > > Hi Rhys, > > > > If you are looking at an MRTG style graph, then as Jim points out you > > are probably looking at a 5 minute rolling average, and the peaks will > > very likely be much higher and yes possibly impacting performance. > > > > For a more instant view of the CPU, do a "show proc cpu history", this > > will show you the spikes (assuming csco). > > > > Assuming the box you are using is not just under-powered, you need to > > look at what is hitting the cpu and see if you can control/remove it. > > > > Chasing "links that don't seem to go as hard as they should", oh man, > > that's such a can of subjective worms...... > > > > > > On Fri, April 6, 2018 10:51 am, Jim Woodward wrote: > > > On 06-04-2018 10:21, Rhys Cuff (Latrobe I.T) wrote: > > > > > > > > > Hi Rhys, > > > > > > > > > If it's a Cisco I have found that once you start hitting 70% you'll > > > start to see Latency creep up, this in turn will likely to have an > > > overall effect on achievable speeds. > > > > > > If the 70% figure is an average then peaks may be quite a bit > > > higher, I would consider working on a plan to upgrade the device(s) > > > or do the usual process of looking at your configuration to see if > > > you have any misconfigured/redundant ACL's or or routing policies > > > that may be eating into your CPU performance. > > > > > > Kind Regards, > > > > > > > > > Jim. > > > > > > > > >> FROM: AusNOG [mailto:ausnog-boun...@lists.ausnog.net] ON BEHALF > OF > > >> Rhys Cuff (Latrobe I.T) > > >> SENT: Friday, April 6, 2018 10:19 AM > > >> TO: ausnog@lists.ausnog.net > > >> SUBJECT: [AusNOG] CPU - when to upfrade > > >> > > >> > > >> Hi Guys > > >> > > >> > > >> When you have a router and cpu is hitting about 60 - 70% with > > >> traffic load would that impact speeds? > > >> > > >> I've got a few links that don't seem to go as hard as they should, > > >> but I can't find the > > >> reason._______________________________________________ > > >> > > > AusNOG mailing list > > > AusNOG@lists.ausnog.net > > > http://lists.ausnog.net/mailman/listinfo/ausnog > > > > > > > > > > > > _______________________________________________ > > AusNOG mailing list > > AusNOG@lists.ausnog.net > > http://lists.ausnog.net/mailman/listinfo/ausnog > > _______________________________________________ > AusNOG mailing list > AusNOG@lists.ausnog.net > http://lists.ausnog.net/mailman/listinfo/ausnog _______________________________________________ AusNOG mailing list AusNOG@lists.ausnog.net http://lists.ausnog.net/mailman/listinfo/ausnog