If problem persists I've got a script the you can schedule to run and it'll do this for you.
On Mon, Sep 9, 2019 at 10:40 AM Alex Wakefield < [email protected]> wrote: > Hi all, > > Thanks for all the config! I can't explain it, but just doing the > release/renew command below managed to make my setup "just work". > > Hope everyone has a great week! > > Regards, > Alex > > > On Sun, 8 Sep 2019, at 5:21 PM, Chris Lee wrote: > > Hi Alex, > > > > Yes have ER-X running 2.0.6 working well with ABB.. some snippet of > interface and firewall stanzas below. I put the dhcpv6-pd on switch0 > interface for my local LAN. I have a virtual interface on the WAN port as > well to manage the Netcomm NFV modem from ABB that I put into bridge mode. > Also have a Netgear 4G ethernet router on the second ethernet port that I > use the load-balancing features with to failover to 4G automatically if > NBN/ABB becomes unavailable (but haven't enabled IPv6 on the 4G yet), so > far works fairly well. > > > > On occasion when there's been issues with IPv6 I've found I've had to > manually release/delete the DUID and renew dhcpv6-pd on the edgerouter with > the commands below. > > > > release dhcpv6-pd interface eth0 > > delete dhcpv6-pd duid > > renew dhcpv6-pd interface eth0 > > > > other than that just show interfaces and you should see your /128 IA-NA > IPv6 address on the eth0 interface and a /64 from the IA-PD on switch0 > interface. > > > > interfaces { > > ethernet eth0 { > > address dhcp > > description "WAN Aussie Broadband FTTN" > > dhcp-options { > > default-route update > > default-route-distance 10 > > name-server no-update > > } > > dhcpv6-pd { > > pd 0 { > > interface switch0 { > > host-address ::1 > > prefix-id :1 > > service slaac > > } > > prefix-length /56 > > } > > rapid-commit disable > > } > > duplex auto > > firewall { > > in { > > ipv6-name WANv6_IN > > name WAN_IN > > } > > local { > > ipv6-name WANv6_LOCAL > > name WAN_LOCAL > > } > > } > > speed auto > > vif 3 { > > address 10.1.1.2/24 > > description "NetComm Management" > > firewall { > > in { > > name WAN_IN > > } > > local { > > name WAN_LOCAL > > } > > } > > mtu 1500 > > } > > } > > } > > > > > > firewall { > > ipv6-name WANv6_IN { > > default-action drop > > description "WAN inbound traffic forwarded to LAN" > > enable-default-log > > rule 10 { > > action accept > > description "Allow established/related sessions" > > protocol all > > state { > > established enable > > related enable > > } > > } > > rule 20 { > > action drop > > description "Drop invalid state" > > protocol all > > state { > > invalid enable > > } > > } > > rule 30 { > > action accept > > description "allow ICMPv6" > > protocol icmpv6 > > } > > } > > ipv6-name WANv6_LOCAL { > > default-action drop > > description "WAN inbound traffic to the router" > > enable-default-log > > rule 10 { > > action accept > > description "Allow established/related sessions" > > protocol all > > state { > > established enable > > related enable > > } > > } > > rule 20 { > > action drop > > description "Drop invalid state" > > protocol all > > state { > > invalid enable > > } > > } > > rule 30 { > > action accept > > description "Allow IPv6 icmp" > > protocol ipv6-icmp > > } > > rule 40 { > > action accept > > description "allow dhcpv6" > > destination { > > port 546 > > } > > protocol udp > > source { > > port 547 > > } > > } > > } > > ipv6-receive-redirects disable > > ipv6-src-route disable > > ip-src-route disable > > log-martians disable > > } > > > > Regards, > > Chris > > > > On Sun, Sep 8, 2019 at 2:14 PM Alex Wakefield < > [email protected]> wrote: > >> Hi, > >> > >> Does anyone have a working IPv6 setup for an EdgeRouter using the > AussieBB beta? I'm using an EdgeRouter Lite running v2.0.6. > >> > >> My internal interface manages to get IPs out of the range handed out > by Aussie but clients never get an address after that. I'm trying to use > SLAAC to hand out IPs. Relevant config on my internet facing port below. > >> > >> ethernet eth0 { > >> address dhcp > >> description AussieBB > >> dhcpv6-pd { > >> pd 1 { > >> interface eth2.20 { > >> host-address ::1 > >> no-dns > >> prefix-id 0 > >> service slaac > >> } > >> prefix-length 56 > >> } > >> rapid-commit enable > >> } > >> duplex auto > >> firewall { > >> in { > >> ipv6-name AussieIn > >> name AussieIn > >> } > >> local { > >> ipv6-name AussieLocal > >> name AussieLocal > >> } > >> out { > >> ipv6-name AussieOut > >> name AussieOut > >> } > >> } > >> ipv6 { > >> address { > >> autoconf > >> } > >> } > >> speed auto > >> } > >> > >> Regards, > >> Alex > >> _______________________________________________ > >> AusNOG mailing list > >> [email protected] > >> http://lists.ausnog.net/mailman/listinfo/ausnog > > _______________________________________________ > > AusNOG mailing list > > [email protected] > > http://lists.ausnog.net/mailman/listinfo/ausnog > > > _______________________________________________ > AusNOG mailing list > [email protected] > http://lists.ausnog.net/mailman/listinfo/ausnog >
_______________________________________________ AusNOG mailing list [email protected] http://lists.ausnog.net/mailman/listinfo/ausnog
