Then I change commd into `awk '/ACTIVE/' stdout | head -4`, it failed
again, log is :

./netdev-dpdk.at:28: awk '/ACTIVE/' stdout | head -4
> --- -   2017-08-09 17:41:24.809066088 +0800
> +++ /home/gangyewei-3/mvs/mvs/tests/testsuite.dir/at-groups/789/stdout
>  2017-08-09 17:41:24.807150522 +0800
> @@ -1,5 +1,5 @@
> -LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> -     partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> -LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> -     partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> +LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> +     partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> +LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> +     partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
> 789. netdev-dpdk.at:23: 789. netdev-dpdk - dpdk/bond-show (
> netdev-dpdk.at:23): FAILED (netdev-dpdk.at:28)


I don't know where is the difference....

2017-08-09 17:15 GMT+08:00 Sam <batmanu...@gmail.com>:

> Hi all,
>
> I'm using autotest to test ovs, and I write a new *.at file using only one
> AT_CHECK sentence like this:
>
> AT_CHECK([ovs-appctl dpdk/bond-show dpdkb2], [0], [stdout])
>> AT_CHECK([[sed '/ACTIVE/p' stdout | head -4]], [0], [[LACP actor_state
>> ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>      partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>> LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>      partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING]])
>
>
> but this *.at file failed, log is:
>
> 789. netdev-dpdk.at:23: testing netdev-dpdk - dpdk/bond-show ...
>> ./netdev-dpdk.at:27: ovs-appctl dpdk/bond-show dpdkb2
>> stdout:
>> ---- dpdkb2 ----
>> bond_mode: 4
>> slave 0:
>> active
>> mac address ec:f4:bb:e1:1a:40
>> Link Up - speed 10000 Mbps - full-duplex
>> LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>      partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>  rx pkts=268449, bytes=16502449, mcasts=0, drop=0, errs=0, nombufs=0
>>  tx pkts=261, bytes=32020, errs=0
>> slave 1:
>> active
>> mac address ec:f4:bb:e1:1a:42
>> Link Up - speed 10000 Mbps - full-duplex
>> LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>      partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>  rx pkts=296190, bytes=17934647, mcasts=0, drop=0, errs=0, nombufs=0
>>  tx pkts=254, bytes=31496, errs=0
>> ./netdev-dpdk.at:28: sed '/ACTIVE/p' stdout | head -4
>> --- -   2017-08-09 16:59:18.802810195 +0800
>> +++ /home/gangyewei-3/mvs/mvs/tests/testsuite.dir/at-groups/789/stdout
>>  2017-08-09 16:59:18.801176471 +0800
>> @@ -1,4 +1,5 @@
>> -LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>> -     partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>> -LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>> -     partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>> +---- dpdkb2 ----
>> +bond_mode: 4
>> +
>> +slave 0:
>> +
>> 789. netdev-dpdk.at:23: 789. netdev-dpdk - dpdk/bond-show (
>> netdev-dpdk.at:23): FAILED (netdev-dpdk.at:28)
>
>
> 1. I don't know what "+" "-" means, and why there are "+" and "-"?
> 2. I run `ovs-appctl dpdk/bond-show dpdkb2 | sed -n '/ACTIVE/p' | head
> -4`, result is:
>
>> LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>      partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>> LACP actor_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>>      partner_state ACTIVE AGGREGATION SYNC COLLECTING DISTRIBUTING
>
> That's exactly what I matched in AT_CHECK, why it fails?
>
> Autotest is really hard to use...
>
_______________________________________________
Autoconf mailing list
Autoconf@gnu.org
https://lists.gnu.org/mailman/listinfo/autoconf

Reply via email to