Hello Devs!
I've got another little problem and I cannot get any information about it.
Here is the log:
#-----------------------------------------------------------------------------------------------------------------------------------
avrdude -p m8 -c avrftdi -b 1000000 -U
flash:w:/home//ng/simonK_BLC/tgy_2012-06-10_d8f53c2/tp_i2c.hex:a -v
avrdude: Version 5.11.1, compiled on Oct 18 2011 at 21:41:15
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home//.avrduderc"
User configuration file does not exist or is not a regular
file, skipping
Using Port : /dev/parport0
Using Programmer : avrftdi
Overriding Baud Rate : 1000000
avrdude: device: 040, serial number: ? type 0x0500 found
avrdude: Using device VID:PID 0403:6010 type 0x0500(C/D) and SN '?'.
avrdude: Using USB Interface A
avrdude info: reset pin value: 3
add_pins: 1: 0x0000, inv=0x0000
add_pins: 2: 0x0000, inv=0x0000
add_pin: 7: bit 0x0005 inv=0x0000
add_pin: 8: bit 0x0006 inv=0x0000
add_pin: 9: bit 0x0007 inv=0x0000
add_pin: 10: bit 0x0008 inv=0x0000
avrdude info: clock divisor: 0x0005
AVR Part : ATMEGA8
Chip Erase delay : 10000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page
Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages
MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------
----- ----- ---------
eeprom 4 20 128 0 no 512 4 0
9000 9000 0xff 0xff
flash 33 10 64 0 yes 8192 64 128
4500 4500 0xff 0x00
lfuse 0 0 0 0 no 1 0 0
2000 2000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0
2000 2000 0x00 0x00
lock 0 0 0 0 no 1 0 0
2000 2000 0x00 0x00
calibration 0 0 0 0 no 4 0 0
0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0
0 0 0x00 0x00
Programmer Type : avrftdi
Description : FT2232D based generic programmer
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e9307
avrdude: safemode: lfuse reads as 9F
avrdude: safemode: hfuse reads as C9
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file
"/home//ng/simonK_BLC/tgy_2012-06-10_d8f53c2/tp_i2c.hex"
avrdude: input file
/home//ng/simonK_BLC/tgy_2012-06-10_d8f53c2/tp_i2c.hex auto detected
as Intel Hex
avrdude: writing flash (8192 bytes):
Writing | ################################################## | 99% 0.63s
#-----------------------------------------------------------------------------------------------------------------------------------
After that I have to hit Ctrl-C to get back to command line. But I
dont get any other Information. It appeared from one day to another
without any change on my setup. It simply stops the flashing process.
What can I do??
Thanks in advance
Daniel
_______________________________________________
avrdude-dev mailing list
avrdude-dev@nongnu.org
https://lists.nongnu.org/mailman/listinfo/avrdude-dev
