Thanks again Prabhat for the prompt reply. Yes, this version works. Do you know certification status of this release?
Thanks, Rajan -----Original Message----- From: Prabath Siriwardena [mailto:[email protected]] Sent: Friday, October 16, 2009 1:13 PM To: [email protected] Subject: Re: Axis2 with Rampart 1.4 - Faults are not getting encrypted Can you please try with the build available here [1]. Thanks & regards. -Prabath [1]:http://people.apache.org/~gdaniels/stagingRepo/org/apache/axis2/dist ribution/1.5.1/ Rajan Gupta wrote: > Thanks Prabhat. I tried with Axis2 version 1.5 but encountered the same > issue. I have not tried the nightly build yet. > > Thanks, > Rajan > > -----Original Message----- > From: Prabath Siriwardena [mailto:[email protected]] > Sent: Friday, October 16, 2009 11:50 AM > To: [email protected] > Subject: Re: Axis2 with Rampart 1.4 - Faults are not getting encrypted > > Yes - this is fixed in the Axis2 trunk - so the fix was not available > with 1.4.1 > > Thanks & regards. > -Prabath > > [1]:https://issues.apache.org/jira/browse/RAMPART-164 > [2]:https://issues.apache.org/jira/browse/AXIS2-4241 > > Prabath Siriwardena wrote: > >> AFAIR this issue was fixed after after 1.4.1 release. >> >> I'll verify it for sure and let you know. >> >> Thanks & regards. >> -Prabath >> >> Rajan Gupta wrote: >> >>> Thanks Prabhat for the reply. I am using Axis2 version 1.4.1. Below >>> > is > >>> an extract from my axis2.xml. I see that I already have "Security" in >>> > my > >>> OutFaultFlow. >>> <phaseOrder type="OutFaultFlow"> >>> <!-- user can add his own phases to this area --> >>> <phase name="soapmonitorPhase"/> >>> <phase name="OperationOutFaultPhase"/> >>> <phase name="RMPhase"/> >>> <phase name="PolicyDetermination"/> >>> <phase name="MessageOut"/> >>> <phase name="Security"/> >>> </phaseOrder> >>> >>> Is this functionality supposed to work in Axis2 1.4.1. Upgrading to >>> Axis2 1.5 might not be possible for the time being. >>> Thanks, >>> Rajan >>> -----Original Message----- >>> From: Prabath Siriwardena [mailto:[email protected]] Sent: Friday, >>> October 16, 2009 10:08 AM >>> To: [email protected] >>> Subject: Re: Axis2 with Rampart 1.4 - Faults are not getting >>> > encrypted > >>> Hi Rajan; >>> >>> Security will be applied to all the 'application faults' if you have >>> > > >>> defined the 'Security' phase under OutFaultFlow in the axis2.xml of >>> the service end. >>> >>> What is the version of Axis2 you use ? Can you please try with Axis2 >>> > 1.5 > >>> ? >>> >>> Thanks & regards. >>> - Prabath >>> >>> Rajan Gupta wrote: >>> >>> >>>> Hi, >>>> >>>> I am using axis2 with rampart version 1.4. When the operation is >>>> successful the response from the server is encrypted, contains >>>> required security headers, and works fine. In case when the >>>> operation results in a fault, the server sends a clear text >>>> response, similar to >>>> >>>> >>> >>> >>>> a response you would get without engaging rampart. The client is >>>> expecting a secured response and hence fails. >>>> >>>> >>>> >>>> Is there anything special I need to do in rampart or axis2 >>>> configuration for faults? >>>> >>>> >>>> >>>> Thanks in advance, >>>> >>>> Rajan >>>> >>>> >>>> >>> >>> >> > > >
