Hello all
Babel through Openvpn is working if I give ipv6 to tun0 and if Openvpn is point
to point.
But, if I want use Openvpn through babeld, it doesn't work.
may be because address range is not /24?
I use two Ip range: 10.50.1.0 for wireless and 10.50.0.0 to avoid conflicts
between ahcpd and dhcpd
this some log and config:
when I launch Openvpn through Babel on Wifi: (it can't add 88.XXX.XXX.XXX/32
via 10.50.1.3)
...
Thu Apr 10 08:37:54 2014 OPTIONS IMPORT: --ifconfig/up options modified
Thu Apr 10 08:37:54 2014 OPTIONS IMPORT: route options modified
Thu Apr 10 08:37:54 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option
options modified
Thu Apr 10 08:37:54 2014 ROUTE_GATEWAY 10.50.1.3
Thu Apr 10 08:37:54 2014 TUN/TAP device tun0 opened
Thu Apr 10 08:37:54 2014 TUN/TAP TX queue length set to 100
Thu Apr 10 08:37:54 2014 do_ifconfig, tt->ipv6=1, tt->did_ifconfig_ipv6_setup=0
Thu Apr 10 08:37:54 2014 /sbin/ip link set dev tun0 up mtu 1500
Thu Apr 10 08:37:54 2014 /sbin/ip addr add dev tun0 local 10.43.0.2 peer
10.43.0.1
Thu Apr 10 08:37:54 2014 /sbin/ip route add 88.XXX.XXX.XXX/32 via 10.50.1.3
RTNETLINK answers: Network is unreachable
Thu Apr 10 08:37:54 2014 ERROR: Linux route add command failed: external
program exited with error status: 2
Thu Apr 10 08:37:54 2014 /sbin/ip route add 0.0.0.0/1 via 10.43.0.1
Thu Apr 10 08:37:54 2014 /sbin/ip route add 128.0.0.0/1 via 10.43.0.1
Thu Apr 10 08:37:54 2014 /sbin/ip route add 192.168.10.0/24 via 10.43.0.1
Thu Apr 10 08:37:54 2014 Initialization Sequence Completed
after this, my ip and routes are: (eth0 not connected, Wifi only)
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 00:16:d3:46:fb:7d brd ff:ff:ff:ff:ff:ff
inet 10.50.1.130/32 scope global eth0
valid_lft forever preferred_lft forever
inet6 fde6:20f5:c9ac:1050:202:78ff:fe47:4eb2/128 scope global tentative
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group
default qlen 1000
link/ether 00:02:78:47:4e:b2 brd ff:ff:ff:ff:ff:ff
inet 10.50.1.130/32 scope global wlan0
valid_lft forever preferred_lft forever
inet6 fde6:20f5:c9ac:1050:202:78ff:fe47:4eb2/128 scope global
valid_lft forever preferred_lft forever
inet6 fe80::202:78ff:fe47:4eb2/64 scope link
valid_lft forever preferred_lft forever
8: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN group default qlen 100
link/none
inet 10.43.0.2 peer 10.43.0.1/32 scope global tun0
valid_lft forever preferred_lft forever
0.0.0.0/1 via 10.43.0.1 dev tun0
default via 10.50.1.3 dev wlan0 proto 42 onlink
10.41.0.2 via 10.50.1.129 dev wlan0 proto 42 onlink
10.43.0.1 dev tun0 proto kernel scope link src 10.43.0.2
10.50.0.0/24 via 10.50.1.3 dev wlan0 proto 42 onlink
10.50.0.2 via 10.50.1.3 dev wlan0 proto 42 onlink
10.50.0.139 via 10.50.1.129 dev wlan0 proto 42 onlink
10.50.1.3 via 10.50.1.3 dev wlan0 proto 42 onlink
10.50.1.129 via 10.50.1.129 dev wlan0 proto 42 onlink
10.84.0.1 via 10.50.1.129 dev wlan0 proto 42 onlink
128.0.0.0/1 via 10.43.0.1 dev tun0
192.168.0.0/24 via 10.50.1.3 dev wlan0 proto 42 onlink
192.168.0.13 via 10.50.1.3 dev wlan0 proto 42 onlink
192.168.10.0/24 via 10.43.0.1 dev tun0
-------------------
If I use wire (eth0), and dhcp server (it give me inet 10.50.0.195/24 brd
10.50.0.255 )
openvpn work, but it doesn't use babel to reach default route (given by dhcp
server).
Openvpn log: (it can add 88.XXX.XXX.XXX/32 via 10.50.0.2 )
...
Thu Apr 10 08:35:36 2014 OPTIONS IMPORT: --ifconfig/up options modified
Thu Apr 10 08:35:36 2014 OPTIONS IMPORT: route options modified
Thu Apr 10 08:35:36 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option
options modified
Thu Apr 10 08:35:36 2014 ROUTE_GATEWAY 10.50.0.2
Thu Apr 10 08:35:36 2014 TUN/TAP device tun0 opened
Thu Apr 10 08:35:36 2014 TUN/TAP TX queue length set to 100
Thu Apr 10 08:35:36 2014 do_ifconfig, tt->ipv6=1, tt->did_ifconfig_ipv6_setup=0
Thu Apr 10 08:35:36 2014 /sbin/ip link set dev tun0 up mtu 1500
Thu Apr 10 08:35:36 2014 /sbin/ip addr add dev tun0 local 10.43.0.2 peer
10.43.0.1
Thu Apr 10 08:35:36 2014 /sbin/ip route add 88.XXX.XXX.XXX/32 via 10.50.0.2
Thu Apr 10 08:35:36 2014 /sbin/ip route add 0.0.0.0/1 via 10.43.0.1
Thu Apr 10 08:35:36 2014 /sbin/ip route add 128.0.0.0/1 via 10.43.0.1
Thu Apr 10 08:35:36 2014 /sbin/ip route add 192.168.10.0/24 via 10.43.0.1
Thu Apr 10 08:35:36 2014 Initialization Sequence Completed
after this operation, I have:
0.0.0.0/1 via 10.43.0.1 dev tun0
default via 10.50.0.2 dev eth0 proto 42 onlink
10.41.0.2 via 10.50.0.139 dev eth0 proto 42 onlink
10.43.0.1 dev tun43_numericor proto kernel scope link src 10.43.0.2
10.50.0.0/24 dev eth0 proto kernel scope link src 10.50.0.195
10.50.0.2 via 10.50.0.2 dev eth0 proto 42 onlink
10.50.0.139 via 10.50.0.139 dev eth0 proto 42 onlink
10.50.1.3 via 10.50.0.2 dev eth0 proto 42 onlink
10.50.1.129 via 10.50.0.139 dev eth0 proto 42 onlink
10.84.0.1 dev tun84_Miou proto kernel scope link src 10.84.0.2
88.XXX.XXX.XXX via 10.50.0.2 dev eth0
128.0.0.0/1 via 10.43.0.1 dev tun0
192.168.0.0/24 via 10.50.0.2 dev eth0 proto 42 onlink
192.168.0.13 via 10.50.0.2 dev eth0 proto 42 onlink
192.168.10.0/24 via 10.43.0.1 dev tun0
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group
default qlen 1000
link/ether 00:16:d3:46:fb:7d brd ff:ff:ff:ff:ff:ff
inet 10.50.0.195/24 brd 10.50.0.255 scope global eth0
valid_lft forever preferred_lft forever
inet 10.50.1.130/32 scope global eth0
valid_lft forever preferred_lft forever
inet6 fde6:20f5:c9ac:1050:202:78ff:fe47:4eb2/128 scope global
valid_lft forever preferred_lft forever
inet6 fe80::216:d3ff:fe46:fb7d/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group
default qlen 1000
link/ether 00:02:78:47:4e:b2 brd ff:ff:ff:ff:ff:ff
inet 10.50.1.130/32 scope global wlan0
valid_lft forever preferred_lft forever
inet6 fde6:20f5:c9ac:1050:202:78ff:fe47:4eb2/128 scope global
valid_lft forever preferred_lft forever
inet6 fe80::202:78ff:fe47:4eb2/64 scope link
valid_lft forever preferred_lft forever
17: tun84_Miou: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc
pfifo_fast state UNKNOWN group default qlen 100
link/none
inet 10.84.0.2 peer 10.84.0.1/32 scope global tun84_Miou
valid_lft forever preferred_lft forever
inet 10.50.1.130/32 scope global tun84_Miou
valid_lft forever preferred_lft forever
inet6 fde6:20f5:c9ac:1050:202:78ff:fe47:4eb2/128 scope global
valid_lft forever preferred_lft forever
inet6 fe80::bcf2:b5ff:fed6:1084/64 scope link
valid_lft forever preferred_lft forever
18: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN group default qlen 100
link/none
inet 10.43.0.2 peer 10.43.0.1/32 scope global tun0
valid_lft forever preferred_lft forever
(at this time I don't gived link local ipv6 to tun0 yet, and not restarted
ahcpd)
thanks to help me using Openvpn through Babel :p
_______________________________________________
Babel-users mailing list
[email protected]
http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/babel-users
