On Mar 5, 2010, at 12:11 PM, Les Mikesell wrote: > On 3/5/2010 11:21 AM, Summers, James B. II wrote: >> >> Well a reinstall of the OS is not totally out of the question but will have >> to be a last resort. >> >> My latest attempt was to wipe off all config files and binaries. Then did a >> re-install of BackupPC. I also have the suid stuff working in the webserver >> now. But I am confused on whether it is using mod_perl or not? If so, I >> need to remove the suid bit? >> >> I reconfigured a host and then went to that host and asked for a full >> backup. Same results. The odd thing is that the first check comes back as >> ok. But when you go back to the host page, the failed ping count has >> increased. >> >> All firewalls have been turned off and I can ping each address from each end >> of the pipe. >> >> I think this is probably the underlying issue, but I can not get a log to >> help me. >> >> Is there a way to run in debug mode or turn up log level? I found a setting >> to increase the verbosity of XFER, but I do not think I am getting that far? > > If you installed from the tarball you should know if you use mod_perl > because you don't unless you enabled it in the httpd config yourself. >
Wat I meant to say was, is the mod_perl working the way I config'd it? But what I have done since, is totally disable mod_perl and attempt to do a backup from the host. Still no joy and the ping failure is increasing each attempt. > Are you using SElinux? That's a common cause of mysterious problems, > especially when adding things not specifically packaged for the > distribution. No, it always causes grief. # This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - SELinux is fully disabled. SELINUX=disabled # SELINUXTYPE= type of policy in use. Possible values are: # targeted - Only targeted network daemons are protected. # strict - Full SELinux protection. SELINUXTYPE=targeted The configured ping command is: $pingPath -c 1 -w 3 $host and from the command line on the server: /bin/ping -c 1 -w 3 129.15.78.102 PING 129.15.78.102 (129.15.78.102) 56(84) bytes of data. 64 bytes from 129.15.78.102: icmp_seq=0 ttl=128 time=1.46 ms --- 129.15.78.102 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.469/1.469/1.469/0.000 ms, pipe 2 and on the host it can ping back to the server as well from a command prompt. Hmmmmmmm.... Ideas? Thanks! > > -- > Les Mikesell > [email protected] > > > > > ------------------------------------------------------------------------------ > Download Intel® Parallel Studio Eval > Try the new software tools for yourself. Speed compiling, find bugs > proactively, and fine-tune applications for parallel performance. > See why Intel Parallel Studio got high marks during beta. > http://p.sf.net/sfu/intel-sw-dev > _______________________________________________ > BackupPC-users mailing list > [email protected] > List: https://lists.sourceforge.net/lists/listinfo/backuppc-users > Wiki: http://backuppc.wiki.sourceforge.net > Project: http://backuppc.sourceforge.net/ --- Jim Summers School of Computer Science-University of Oklahoma ------------------------------------------------------------------------------ Download Intel® Parallel Studio Eval Try the new software tools for yourself. Speed compiling, find bugs proactively, and fine-tune applications for parallel performance. See why Intel Parallel Studio got high marks during beta. http://p.sf.net/sfu/intel-sw-dev _______________________________________________ BackupPC-users mailing list [email protected] List: https://lists.sourceforge.net/lists/listinfo/backuppc-users Wiki: http://backuppc.wiki.sourceforge.net Project: http://backuppc.sourceforge.net/
