Hi,
On 3/28/2007 6:34 PM, Rui Goncalves wrote:
>
> Dear Arno,
>
> Thanks for your kind reply.
>
>
> The test was made with others Volumes in autochanger
>
> After executed yours suggestions I think that it is all good with the
> autochanger(/dev/sg0) and the drive(/dev/nst0) .
Good... then I suspect the tape drive needs more time to recognize the
tape. Use the function wait_for_drive (or similar...) in mtx-changer if
possible, or try a longer wait time after loading the tape. DLT can take
up to some minutes.
> Only commands that seem does not run well is:
> mt -f /dev/nst0 rewind - It finishes immediately
That's interesting... are you sure it returns immedeiately even if the
tape is not already rewound? When you always test with the rewinding
devices, the above observation would be expected, but doing a 'mt -f
/dev/nst0 fsf 200' you should see a higher block positio with 'mt
status', and rewinding should take some time.
> mt -f /dev/nst0 retension - It finishes immediately. It would have to
> take some time
There are tape drives that don't support retensioning, because the
manufacturesrs decided these tapes don't need to be retensioned...
mostly the single-reel technology.
Arno
> TESTING
>
> mt -f /dev/nst0 status
>
> SCSI 2 tape drive:
> File number=-1, block number=-1, partition=0.
> Tape block size 0 bytes. Density code 0x0 (default).
> Soft error count since last status=0
> General status bits on (50000):
> DR_OPEN IM_REP_EN
>
> mtx -f /dev/sg0 status
>
> Storage Changer /dev/sg0:1 Drives, 9 Slots ( 0 Import/Export )
> Data Transfer Element 0:Empty
> Storage Element 1:Full :VolumeTag=UG2029L1
> Storage Element 2:Full :VolumeTag=UG2004L1
> Storage Element 3:Full :VolumeTag=UG2038L1
> Storage Element 4:Full :VolumeTag=UG2039L1
> Storage Element 5:Full :VolumeTag=UG2043L1
> Storage Element 6:Full :VolumeTag=UG2035L1
> Storage Element 7:Full :VolumeTag=UG2040L1
> Storage Element 8:Full :VolumeTag=UG2041L1
> Storage Element 9:Full :VolumeTag=UG2042L1
>
> mtx -f /dev/sg0 load 1
>
> mtx -f /dev/sg0 status
>
> Storage Changer /dev/sg0:1 Drives, 9 Slots ( 0 Import/Export )
> Data Transfer Element 0:Full (Storage Element 1 Loaded):VolumeTag =
> UG2029L1
> Storage Element 1:Empty:VolumeTag=
> Storage Element 2:Full :VolumeTag=UG2004L1
> Storage Element 3:Full :VolumeTag=UG2038L1
> Storage Element 4:Full :VolumeTag=UG2039L1
> Storage Element 5:Full :VolumeTag=UG2043L1
> Storage Element 6:Full :VolumeTag=UG2035L1
> Storage Element 7:Full :VolumeTag=UG2040L1
> Storage Element 8:Full :VolumeTag=UG2041L1
> Storage Element 9:Full :VolumeTag=UG2042L1
>
> mt -f /dev/nst0 status
>
> SCSI 2 tape drive:
> File number=0, block number=0, partition=0.
> Tape block size 0 bytes. Density code 0x40 (DLT1 40 GB, or Ultrium).
> Soft error count since last status=0
> General status bits on (41010000):
> BOT ONLINE IM_REP_EN
>
>
> mtx -f /dev/sg0 unload 1
> Unloading Data Transfer Element into Storage Element 1...done
>
> mtx -f /dev/sg0 status
>
> Storage Changer /dev/sg0:1 Drives, 9 Slots ( 0 Import/Export )
> Data Transfer Element 0:Empty
> Storage Element 1:Full :VolumeTag=UG2029L1
> Storage Element 2:Full :VolumeTag=UG2004L1
> Storage Element 3:Full :VolumeTag=UG2038L1
> Storage Element 4:Full :VolumeTag=UG2039L1
> Storage Element 5:Full :VolumeTag=UG2043L1
> Storage Element 6:Full :VolumeTag=UG2035L1
> Storage Element 7:Full :VolumeTag=UG2040L1
> Storage Element 8:Full :VolumeTag=UG2041L1
> Storage Element 9:Full :VolumeTag=UG2042L1
>
> mt -f /dev/nst0 status
>
> SCSI 2 tape drive:
> File number=-1, block number=-1, partition=0.
> Tape block size 0 bytes. Density code 0x0 (default).
> Soft error count since last status=0
> General status bits on (50000):
> DR_OPEN IM_REP_EN
>
> ./mtx-changer /dev/sg0 load 1 /dev/nst0 0
>
> mtx -f /dev/sg0 status
>
> Storage Changer /dev/sg0:1 Drives, 9 Slots ( 0 Import/Export )
> Data Transfer Element 0:Full (Storage Element 1 Loaded):VolumeTag =
> UG2029L1
> Storage Element 1:Empty:VolumeTag=
> Storage Element 2:Full :VolumeTag=UG2004L1
> Storage Element 3:Full :VolumeTag=UG2038L1
> Storage Element 4:Full :VolumeTag=UG2039L1
> Storage Element 5:Full :VolumeTag=UG2043L1
> Storage Element 6:Full :VolumeTag=UG2035L1
> Storage Element 7:Full :VolumeTag=UG2040L1
> Storage Element 8:Full :VolumeTag=UG2041L1
> Storage Element 9:Full :VolumeTag=UG2042L1
>
> mtx -f /dev/sg0 unload 1
> Unloading Data Transfer Element into Storage Element 1...done
>
> mtx -f /dev/sg0 status
>
> Storage Changer /dev/sg0:1 Drives, 9 Slots ( 0 Import/Export )
> Data Transfer Element 0:Empty
> Storage Element 1:Full :VolumeTag=UG2029L1
> Storage Element 2:Full :VolumeTag=UG2004L1
> Storage Element 3:Full :VolumeTag=UG2038L1
> Storage Element 4:Full :VolumeTag=UG2039L1
> Storage Element 5:Full :VolumeTag=UG2043L1
> Storage Element 6:Full :VolumeTag=UG2035L1
> Storage Element 7:Full :VolumeTag=UG2040L1
> Storage Element 8:Full :VolumeTag=UG2041L1
> Storage Element 9:Full :VolumeTag=UG2042L1
>
> TEST WITH SLOT 2
>
> ./mtx-changer /dev/sg0 load 2 /dev/nst0 0
>
> mtx -f /dev/sg0 status
>
> Storage Changer /dev/sg0:1 Drives, 9 Slots ( 0 Import/Export )
> Data Transfer Element 0:Full (Storage Element 2 Loaded):VolumeTag =
> UG2004L1
> Storage Element 1:Full :VolumeTag=UG2029L1
> Storage Element 2:Empty:VolumeTag=
> Storage Element 3:Full :VolumeTag=UG2038L1
> Storage Element 4:Full :VolumeTag=UG2039L1
> Storage Element 5:Full :VolumeTag=UG2043L1
> Storage Element 6:Full :VolumeTag=UG2035L1
> Storage Element 7:Full :VolumeTag=UG2040L1
> Storage Element 8:Full :VolumeTag=UG2041L1
> Storage Element 9:Full :VolumeTag=UG2042L1
>
> mt -f /dev/nst0 status
>
> SCSI 2 tape drive:
> File number=0, block number=0, partition=0.
> Tape block size 0 bytes. Density code 0x40 (DLT1 40 GB, or Ultrium).
> Soft error count since last status=0
> General status bits on (41010000):
> BOT ONLINE IM_REP_EN
>
>
>
> MESSAGES FROM THE RESTORE OPERATION that it finished with error
>
>
> ============== bconsole EXECUTION LOG
>
> Job started. JobId=7342
> *
> You have messages.
> *messages
> 26-Mar 17:47 lis-backup-dir: Start Restore Job
> RestoreFiles.2007-03-26_17.47.15
> 26-Mar 17:47 lis-backup-sd: 3301 Issuing autochanger "loaded drive 0"
> command.
> 26-Mar 17:47 lis-backup-sd: 3302 Autochanger "loaded drive 0", result:
> nothing loaded.
> 26-Mar 17:47 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Warning:
> acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium found.
>
> 26-Mar 17:47 lis-backup-sd: 3301 Issuing autochanger "loaded drive 0"
> command.
> 26-Mar 17:47 lis-backup-sd: 3302 Autochanger "loaded drive 0", result:
> nothing loaded.
> 26-Mar 17:47 lis-backup-sd: 3304 Issuing autochanger "load slot 1, drive
> 0" command.
>
> You have messages.
> *messages
> 26-Mar 17:48 lis-backup-sd: 3305 Autochanger "load slot 1, drive 0",
> status is OK.
> 26-Mar 17:48 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Warning:
> acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium found.
>
> 26-Mar 17:48 lis-backup-sd: Please mount Volume "UG2027L1" on Storage
> Device "Drive-1" (/dev/nst0) for Job RestoreFiles.2007-03-26_17.47.15
>
> *mount storage=HP
>
> 3001 OK mount. Device="Drive-1" (/dev/nst0)
>
> You have messages.
> *messages
> 26-Mar 17:49 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Warning:
> acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium found.
>
> 26-Mar 17:49 lis-backup-sd: 3301 Issuing autochanger "loaded drive 0"
> command.
> 26-Mar 17:49 lis-backup-sd: 3302 Autochanger "loaded drive 0", result is
> Slot 1.
> 26-Mar 17:49 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Warning:
> acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium found.
>
> 26-Mar 17:49 lis-backup-sd: Please mount Volume "UG2027L1" on Storage
> Device "Drive-1" (/dev/nst0) for Job RestoreFiles.2007-03-26_17.47.15
>
> *mount storage=HP
>
> 3001 OK mount. Device="Drive-1" (/dev/nst0)
> You have messages.
>
> *messages
> 26-Mar 17:53 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Warning:
> acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium found.
>
> 26-Mar 17:53 lis-backup-sd: 3301 Issuing autochanger "loaded drive 0"
> command.
> 26-Mar 17:53 lis-backup-sd: 3302 Autochanger "loaded drive 0", result is
> Slot 1.
> 26-Mar 17:53 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Fatal
> error: acquire.c:264 Too many errors trying to mount device "Drive-1"
> (/dev/nst0).
> 26-Mar 18:00 www-fd: RestoreFiles.2007-03-26_17.47.15 Fatal error:
> ../../filed/job.c:1752 Bad response to Read Data command. Wanted 3000 OK
> data
> , got 3000 error
>
> 26-Mar 17:53 lis-backup-dir: RestoreFiles.2007-03-26_17.47.15 Error:
> Bacula 1.38.2 (20Nov05): 26-Mar-2007 17:53:27
> JobId: 7342
> Job: RestoreFiles.2007-03-26_17.47.15
> Client: www-fd
> Start time: 26-Mar-2007 17:47:17
> End time: 26-Mar-2007 17:53:27
> Files Expected: 3
> Files Restored: 0
> Bytes Restored: 0
> Rate: 0.0 KB/s
> FD Errors: 0
> FD termination status: Error
> SD termination status: Error
> Termination: *** Restore Error ***
>
> 26-Mar 17:53 lis-backup-dir: Begin pruning Jobs.
> 26-Mar 17:53 lis-backup-dir: No Jobs found to prune.
> 26-Mar 17:53 lis-backup-dir: Begin pruning Files.
> 26-Mar 17:53 lis-backup-dir: No Files found to prune.
> 26-Mar 17:53 lis-backup-dir: End auto prune.
>
> *
>
>
> IN BACULA-DIR.conf CONFIGURATION
>
> Storage {
> Name = "HP"
> Maximum Concurrent Jobs = 4
> Device = Drive-1 # must be same as Device in
> Storage daemon
> Media Type = DLT-8000
> Address = lis-backup # N.B. Use a fully qualified name here
> SDPort = 9103
> Password = "XXXXXXX" # password for Storage daemon
> AutoChanger = yes
> }
>
>
> IN BACULA-SD.CONF CONFIGURATION
>
> Autochanger {
> Name = Autochanger
> Device = Drive-1
> Changer Command = "/etc/bacula/mtx-changer %c %o %S %a %d"
> Changer Device = /dev/sg0
> }
>
> Device {
> Name = Drive-1 #
> Drive Index = 0
> Media Type = DLT-8000
> Archive Device = /dev/nst0
> AutomaticMount = yes; # when device opened, read it
> AlwaysOpen = yes;
> RemovableMedia = yes;
> RandomAccess = no;
> AutoChanger = yes
> # # Enable the Alert command only if you have the mtx package loaded
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
>
> */ Rui Gonçalves /*
>
> -----Original Message-----
> *From:* [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] *On Behalf Of *Rui
> Goncalves
> *Sent:* quarta-feira, 28 de Março de 2007 10:09
> *To:* Bacula-Users
> *Subject:* [Bacula-users] bconsole restore error
>
>
> Please Help!
>
> Bacula 1.38.2 on Linux RedHat.
>
> During a bconsole restore a get this msg:
>
> 26-Mar 17:48 lis-backup-sd: Please mount Volume "UG2027L1" on
> Storage Device "Drive-1" (/dev/nst0) for Job
> RestoreFiles.2007-03-26_17.47.15
>
> Then I give the command mount storage= HP but the job ends with error.
>
> The mount command is correct? If not which is the right form.
>
> The required volume was loaded from autochanger (/dev/sg0) to the
> drive (/dev/nst0)
>
> Thanks for the help.
>
> Rui Goncalves
>
>
> BACULA-DIR.conf CONFIGURATION
>
> Storage {
> Name = "HP"
> Maximum Concurrent Jobs = 4
> Device = Drive-1 # must be same as Device in
> Storage daemon
> Media Type = DLT-8000
> Address = lis-backup # N.B. Use a fully qualified
> name here
> SDPort = 9103
> Password = "XXXXXXX" # password for Storage daemon
> AutoChanger = yes
> }
>
>
> BACULA-SD.CONF CONFUGURATION
>
> Autochanger {
> Name = Autochanger
> Device = Drive-1
> Changer Command = "/etc/bacula/mtx-changer %c %o %S %a %d"
> Changer Device = /dev/sg0
> }
>
> Device {
> Name = Drive-1 #
> Drive Index = 0
> Media Type = DLT-8000
> Archive Device = /dev/nst0
> AutomaticMount = yes; # when device opened, read it
> AlwaysOpen = yes;
> RemovableMedia = yes;
> RandomAccess = no;
> AutoChanger = yes
> # # Enable the Alert command only if you have the mtx package loaded
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
>
> ============== bconsole EXECUTION LOG
>
> *restore
> Using default Catalog name=MyCatalog DB=bacula
>
> First you select one or more JobIds that contain files
> to be restored. You will be presented several methods
> of specifying the JobIds. Then you will be allowed to
> select which files from those JobIds are to be restored.
>
> To select the JobIds, you have the following choices:
> 1: List last 20 Jobs run
> 2: List Jobs where a given File is saved
> 3: Enter list of comma separated JobIds to select
> 4: Enter SQL list command
> 5: Select the most recent backup for a client
> 6: Select backup for a client before a specified time
> 7: Enter a list of files to restore
> 8: Enter a list of files to restore before a specified time
> 9: Find the JobIds of the most recent backup for a client
> 10: Find the JobIds for a backup for a client before a specified
> time
> 11: Enter a list of directories to restore for found JobIds
> 12: Cancel
> Select item: (1-12): 3
>
> Enter JobId(s), comma separated, to restore: 7235
> You have selected the following JobId: 7235
>
> Building directory tree for JobId 7235 ...
> ++++++++++++++++++++++++++++++++++++++++++++++++
> 1 Job, 7,650 files inserted into the tree.
>
> You are now entering file selection mode where you add (mark) and
> remove (unmark) files to be restored. No files are initially added,
> unless
> you used the "all" keyword on the command line.
> Enter "done" to leave this mode.
>
> cwd is: /
> $
>
> $ ls
> C:/
> K:/
> $ cd K:/
> cwd is: K:/
> $ ls
> 40abda4f950fb75ba5/
> System Volume Information
> $ mark *
> 3 files marked.
> $ lsmark
> *40abda4f950fb75ba5/
> *%temp%dd_msxml_retMSI.txt
> *System Volume Information
> $
>
>
> Bootstrap records written to
>
> /var/bacula/working/lis-backup-dir.restore.*Console*.2007-03-26_17.42.12.bsr
>
>
> The job will require the following Volumes:
>
> UG2027L1
>
>
> 3 files selected to be restored.
>
> Defined Clients:
> 1: lis-backup-fd
> 2: ffranco-fd
> 3: matou-fd
> 4: rg-fd
> 5: mail-fd
> 6: fileserver-fd
> 7: egtfilesrv-fd
> 8: lxdc-fd
> 9: clp-0937-fd
> 10: clp-0961-fd
> 11: proxy-fd
> 12: clp-0967-fd
> 13: lxmail-fd
> 14: printserver-fd
> 15: dezdc-fd
> 16: logtec-fd
> 17: owa-fd
> 18: mssql-fd
> 19: compta-vpn-fd
> 20: faxserver-fd
> 21: remedy-fd
> 22: dnsdominio-fd
> 23: smtp-fd
> 24: www-fd
> 25: websweeper-fd
> 26: clp-0915-fd
> 27: asterix-fd
> 28: cluster2-fd
> 29: cluster1-fd
> 30: clp1080-fd
> 31: clp1079-fd
> Select the Client (1-31): 24
>
> Run Restore job
> JobName: RestoreFiles
> Bootstrap:
>
> /var/bacula/working/lis-backup-dir.restore.*Console*.2007-03-26_17.42.12.bsr
> Where: /tmp/bacula-restores
> Replace: always
> FileSet: CatalogSet
> Client: www-fd
> Storage: HP
> When: 2007-03-26 17:45:37
> Catalog: MyCatalog
> Priority: 10
> OK to run? (yes/mod/no): mod
>
> Parameters to modify:
> 1: Level
> 2: Storage
> 3: Job
> 4: FileSet
> 5: Client
> 6: When
> 7: Priority
> 8: Bootstrap
> 9: Where
> 10: Replace
> 11: JobId
> Select parameter to modify (1-11): 9
> Please enter path prefix for restore (/ for none): K:/
> Run Restore job
> JobName: RestoreFiles
> Bootstrap:
>
> /var/bacula/working/lis-backup-dir.restore.*Console*.2007-03-26_17.42.12.bsr
> Where: K:/
> Replace: always
> FileSet: CatalogSet
> Client: www-fd
> Storage: HP
> When: 2007-03-26 17:45:37
> Catalog: MyCatalog
> Priority: 10
> OK to run? (yes/mod/no): yes
>
> Job started. JobId=7342
> *
> You have messages.
> *messages
> 26-Mar 17:47 lis-backup-dir: Start Restore Job
> RestoreFiles.2007-03-26_17.47.15
> 26-Mar 17:47 lis-backup-sd: 3301 Issuing autochanger "loaded drive
> 0" command.
> 26-Mar 17:47 lis-backup-sd: 3302 Autochanger "loaded drive 0",
> result: nothing loaded.
> 26-Mar 17:47 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15
> Warning: acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium
> found.
>
> 26-Mar 17:47 lis-backup-sd: 3301 Issuing autochanger "loaded drive
> 0" command.
> 26-Mar 17:47 lis-backup-sd: 3302 Autochanger "loaded drive 0",
> result: nothing loaded.
> 26-Mar 17:47 lis-backup-sd: 3304 Issuing autochanger "load slot 1,
> drive 0" command.
>
> You have messages.
> *messages
> 26-Mar 17:48 lis-backup-sd: 3305 Autochanger "load slot 1, drive 0",
> status is OK.
> 26-Mar 17:48 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15
> Warning: acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium
> found.
>
> 26-Mar 17:48 lis-backup-sd: Please mount Volume "UG2027L1" on
> Storage Device "Drive-1" (/dev/nst0) for Job
> RestoreFiles.2007-03-26_17.47.15
>
> *mount storage=HP
>
> 3001 OK mount. Device="Drive-1" (/dev/nst0)
>
> You have messages.
> *messages
> 26-Mar 17:49 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15
> Warning: acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium
> found.
>
> 26-Mar 17:49 lis-backup-sd: 3301 Issuing autochanger "loaded drive
> 0" command.
> 26-Mar 17:49 lis-backup-sd: 3302 Autochanger "loaded drive 0",
> result is Slot 1.
> 26-Mar 17:49 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15
> Warning: acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium
> found.
>
> 26-Mar 17:49 lis-backup-sd: Please mount Volume "UG2027L1" on
> Storage Device "Drive-1" (/dev/nst0) for Job
> RestoreFiles.2007-03-26_17.47.15
>
>
> ================================STATUS STORAGE
>
> *status
> Status available for:
> 1: Director
> 2: Storage
> 3: Client
> 4: All
> Select daemon type for status (1-4): 2
> Automatically selected Storage: HP
> Connecting to Storage daemon HP at lis-backup:9103
>
> lis-backup-sd Version: 1.38.2 (20 November 2005) i686-pc-linux-gnu
> redhat
> Daemon started 23-Mar-07 18:39, 20 Jobs run since started.
>
> Running Jobs:
> Full Restore job RestoreFiles JobId=7342 Volume="UG2027L1"
> pool="Default" device=""Drive-1" (/dev/nst0)"
> Files=0 Bytes=0 Bytes/sec=0
> FDReadSeqNo=16 in_msg=15 out_msg=5 fd=7
> ====
>
> Terminated Jobs:
> JobId Level Files Bytes Status Finished Name
> ======================================================================
> 7334 Incr 64 209,940,691 OK 25-Mar-07 18:00 cluster2
> 7332 Full 2,460,455 509,814,599,281 OK 25-Mar-07 18:24
> clp-0915
> 7333 Full 1 1,846,453,253 OK 25-Mar-07 18:43
> BackupCatalog
> 7335 Incr 39 232,405,418 OK 25-Mar-07 19:00 cluster1
> 7336 Full 1 1,846,381,557 OK 25-Mar-07 23:28
> BackupCatalog
> 7337 Full 380 12,048,513,640 OK 26-Mar-07 04:22 cluster2
> 7338 Full 237 40,309,524,482 OK 26-Mar-07 05:58 cluster1
> 7339 0 0 Error 26-Mar-07 15:29
> RestoreFiles
> 7340 0 0 Error 26-Mar-07 16:24
> RestoreFiles
> 7341 0 0 Error 26-Mar-07 16:56
> RestoreFiles
> ====
>
> Device status:
> Autochanger "Autochanger" with devices:
> "Drive-1" (/dev/nst0)
> Device "FileStorage" (/tmp) is not open or does not exist.
> Device "Drive-1" (/dev/nst0) open but no Bacula volume is mounted.
> Device is BLOCKED waiting for media.
> Slot 1 is loaded in drive 0.
> Total Bytes Read=0 Blocks Read=0 Bytes/block=0
> Positioned at File=0 Block=0
> ====
>
> In Use Volume status:
>
> =========================END STATUS
>
>
>
> *mount storage=HP
>
> 3001 OK mount. Device="Drive-1" (/dev/nst0)
> You have messages.
>
> *messages
> 26-Mar 17:53 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15
> Warning: acquire.c:230 Couldn't rewind device "Drive-1" (/dev/nst0):
> ERR=dev.c:689 Rewind error on "Drive-1" (/dev/nst0). ERR=No medium
> found.
>
> 26-Mar 17:53 lis-backup-sd: 3301 Issuing autochanger "loaded drive
> 0" command.
> 26-Mar 17:53 lis-backup-sd: 3302 Autochanger "loaded drive 0",
> result is Slot 1.
> 26-Mar 17:53 lis-backup-sd: RestoreFiles.2007-03-26_17.47.15 Fatal
> error: acquire.c:264 Too many errors trying to mount device
> "Drive-1" (/dev/nst0).
> 26-Mar 18:00 www-fd: RestoreFiles.2007-03-26_17.47.15 Fatal error:
> ../../filed/job.c:1752 Bad response to Read Data command. Wanted
> 3000 OK data
> , got 3000 error
>
> 26-Mar 17:53 lis-backup-dir: RestoreFiles.2007-03-26_17.47.15 Error:
> Bacula 1.38.2 (20Nov05): 26-Mar-2007 17:53:27
> JobId: 7342
> Job: RestoreFiles.2007-03-26_17.47.15
> Client: www-fd
> Start time: 26-Mar-2007 17:47:17
> End time: 26-Mar-2007 17:53:27
> Files Expected: 3
> Files Restored: 0
> Bytes Restored: 0
> Rate: 0.0 KB/s
> FD Errors: 0
> FD termination status: Error
> SD termination status: Error
> Termination: *** Restore Error ***
>
> 26-Mar 17:53 lis-backup-dir: Begin pruning Jobs.
> 26-Mar 17:53 lis-backup-dir: No Jobs found to prune.
> 26-Mar 17:53 lis-backup-dir: Begin pruning Files.
> 26-Mar 17:53 lis-backup-dir: No Files found to prune.
> 26-Mar 17:53 lis-backup-dir: End auto prune.
>
> */ Rui Gonçalves /*
--
IT-Service Lehmann [EMAIL PROTECTED]
Arno Lehmann http://www.its-lehmann.de
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
