I've been around the block with LSI and with adaptec: tried an LSI SYMC101, an adaptec 2940U2W and a 39160. I've removed the library/exchange from the equation, using only the LTO-3 drive (and have actually swapped that drive out for another as well), swapped SCSI cables, and terminators, and still am getting scsi errors. Anyone got any tips/ideas here ?
target2:0:1: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) Vendor: IBM Model: ULTRIUM-TD3 Rev: 73P5 Type: Sequential-Access ANSI SCSI revision: 03 target2:0:1: Beginning Domain Validation target2:0:1: asynchronous target2:0:1: wide asynchronous target2:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62) sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d target2:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62) sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d target2:0:1: Domain Validation detected failure, dropping back target2:0:1: control msgout: c. sym0: TARGET 1 has been reset. target2:0:1: Domain Validation detected failure, dropping back target2:0:1: FAST-40 WIDE SCSI 66.0 MB/s DT (30.3 ns, offset 62) sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d target2:0:1: FAST-40 WIDE SCSI 66.0 MB/s DT (30.3 ns, offset 62) sym0: SCSI parity error detected: SCR1=1 DBC=15000002 SBCL=ae sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d sym0:1: ERROR (0:8) (d-ae-5) (3e/38/8c) @ (scripta 98:870b0000). sym0: script cmd = 800a0000 sym0: regdump: da 10 c0 38 47 3e 01 0a 03 0d 00 ae 80 00 0e 00 00 1c 6f 08 2a 00 00 00. sym0: SCSI BUS reset detected. sym0: SCSI BUS has been reset. target2:0:1: Domain Validation detected failure, dropping back target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) target2:0:1: Domain Validation skipping write tests target2:0:1: Ending Domain Validation scsi 2:0:1:0: Attached scsi generic sg2 type 1 ACPI: PCI Interrupt 0000:05:02.1[B] -> GSI 101 (level, low) -> IRQ 22 sym1: <1010-33> rev 0x1 at pci 0000:05:02.1 irq 22 sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. sym1: SCSI BUS has been reset. scsi3 : sym-2.2.3 ---------------------------------------- Robin P. Blanchard Systems Administrator Information Technology Outreach Services Carl Vinson Institute of Government The University of Georgia fon 706.542.6295 // fax 706.542.6535 ---------------------------------------- ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
