On Mon, Apr 09, 2018 at 10:59:33AM +0200, Roland Hieber wrote:
> The old way does not seem to work for RPi 3, as the UART pins are
> mapped differently and the NOOBS bootcode does not seem to read a
> config.txt.
> 
> Signed-off-by: Roland Hieber <r.hie...@pengutronix.de>
> ---
>  Documentation/boards/bcm2835.rst | 34 ++++++++++++++++++++++++++--------
>  1 file changed, 26 insertions(+), 8 deletions(-)
> ---
> Although Sascha said he had applied the patch, I cannot find traces of
> it in the current master. It probably got lost, so I'm resending it.
> Note that this patch is independent of Lucas' RPi patch series and also
> applies to the current state of RPi support.

Applied, thanks. Yes, now I *really* did.

Sascha

> 
>  - Roland
> 
> diff --git a/Documentation/boards/bcm2835.rst 
> b/Documentation/boards/bcm2835.rst
> index 13cebb01c4..1a78cfba3c 100644
> --- a/Documentation/boards/bcm2835.rst
> +++ b/Documentation/boards/bcm2835.rst
> @@ -1,17 +1,35 @@
> -Broadcom BCM2835
> +Broadcom BCM283x
>  ================
>  
>  Raspberry Pi
>  ------------
>  
> -  1. Prepare a card with a FAT filesystem. Download a tiny NOOBS LITE
> -     zip archive and unpack it into FAT partition.
> -     See http://www.raspberrypi.org/help/noobs-setup/ for details.
> +  1. Prepare an SD or microSD card with a FAT filesystem of at least 30 MB 
> in size.
> +       
> +  2. Download the `Raspberry Pi firmware`_ (120 MB), unzip it, and copy the
> +     contents of the ``boot/`` folder to your card.
>  
> -  2. Compile ``barebox.bin`` image (use ``rpi_defconfig``).
> -     Copy it to the SD/microSD card and name it ``recovery.img``.
> +  3. Use ``make rpi_defconfig; make`` to build barebox. This will create the 
> following images:
>  
> -  3. Connect to board's UART (115200 8N1);
> +     - ``images/barebox-raspberry-pi-1.img`` for the BCM2835/ARM1176JZF-S 
> (Raspberry Pi 1)
> +     - ``images/barebox-raspberry-pi-2.img`` for the BCM2836/CORTEX-A7 
> (Raspberry Pi 2)
> +     - ``images/barebox-raspberry-pi-3.img`` for the BCM2837/CORTEX-A53 
> (Raspberry Pi 3, Raspberry Pi Zero)
> +    
> +     Copy the respective image for your model to your SD card and name it
> +     ``barebox.img``.
> +
> +  4. Create a text file ``config.txt`` on the SD card with the following 
> content::
> +
> +         kernel=barebox.img
> +         enable_uart=1
> +         dtoverlay=pi3-miniuart-bt
> +
> +     (For more information, refer to the `documentation for config.txt`_.)
> +
> +  5. Connect to board's UART (115200 8N1);
>       Use PIN6 (GND), PIN8 (UART_TX), PIN10 (UART_RX) pins.
>  
> -  4. Turn board's power on.
> +  6. Turn board's power on.
> +
> +.. _Raspberry Pi firmware: 
> https://codeload.github.com/raspberrypi/firmware/zip/80e1fbeb78f9df06701d28c0ed3a3060a3f557ef
> +.. _documentation for config.txt: 
> https://www.raspberrypi.org/documentation/configuration/config-txt/
> -- 
> 2.11.0
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Reply via email to