I would remove those max runtime / wait etc until you have it working. There is often confusion with those settings.
I have had jobs run for over a day no issue. Sent from my iPhone Brock Palen > On Nov 11, 2022, at 5:42 AM, 'Christian Sacks' via bareos-users > <[email protected]> wrote: > > I was premature, it was a one off fluke. Back to the drawing board. > >> On Thursday, 10 November 2022 at 15:31:41 UTC Christian Sacks wrote: >> I have got it working, finally!!! >> >> # grep -ir heartbeat|grep -v \# >> bareos-sd.d/storage/bareos-sd.conf: Heartbeat Interval = 60 seconds >> bareos-dir.d/director/bareos-dir.conf: Heartbeat Interval = 60 seconds >> bareos-fd.d/client/myself.conf: Heartbeat Interval = 60 seconds >> >> Woohoo!! >> >> >>> On Thursday, 10 November 2022 at 14:00:42 UTC Christian Sacks wrote: >>> Hi, thought I'd check back and realised I hadn't posted my reply before; >>> >>> I have these in the job's .conf file; >>> >>> MaxRunSchedTime = 2 hours >>> MaxRunTime = 1 hours >>> MaxWaitTime = 1 hours >>> >>> Yet still as soon as it gets to >>> Elapsed time: 32 mins 20 secs >>> it just automatically cancels the job and fails with >>> FD termination status: Fatal Error >>> >>> I'm so stumped. >>> Thanks for your helps. >>> >>>> On Friday, 8 July 2022 at 13:53:05 UTC+1 [email protected] wrote: >>>> Check if parameter set Max Run Sched Time in bareos-dir.d/job/your_job.conf >>>> >>>> понедельник, 27 июня 2022 г. в 17:40:39 UTC+3, Bruno Friedmann: >>>>> Didn't you have some firewall just cutting the connection because they >>>>> believe it is hang out ? >>>>> >>>>> Did you already tried to setup HeartbeatInterval >>>>> https://docs.bareos.org/Configuration/Director.html#config-Dir_Client_HeartbeatInterval >>>>> instead of ConnectTimeout ? >>>>> >>>>>> On Friday, June 24, 2022 at 12:01:07 PM UTC+2 [email protected] >>>>>> wrote: >>>>>> Hello there, >>>>>> >>>>>> I am about done pulling my hair out trying to find where I need to >>>>>> adjust a timeout setting for a job that takes longer than 30 minutes to >>>>>> run. >>>>>> >>>>>> I have a job that before running will create a snapshot in ceph for a >>>>>> vm's disks, pull the snapshot to the backup server, extract it into a >>>>>> folder and then backup the contents of that folder however the disk is >>>>>> quite large that it backs up and so takes longer than 30 minutes to >>>>>> create/pull/extract the snapshot. >>>>>> >>>>>> I have added the "FD Connect Timeout" and "SD Connect Timeout" with a >>>>>> value of 14400 seconds to the following files; >>>>>> >>>>>> # grep -ir timeout >>>>>> bareos-sd.d/storage/bareos-sd.conf: FD Connect Timeout = 14400 seconds >>>>>> bareos-sd.d/storage/bareos-sd.conf: SD Connect Timeout = 14400 seconds >>>>>> bareos-dir.d/director/bareos-dir.conf: FD Connect Timeout = 14400 >>>>>> seconds >>>>>> bareos-dir.d/director/bareos-dir.conf: SD Connect Timeout = 14400 >>>>>> seconds >>>>>> bareos-fd.d/client/myself.conf: SD Connect Timeout = 14400 seconds >>>>>> bareos-fd.d/client/myself.conf: FD Connect Timeout = 14400 seconds >>>>>> >>>>>> The job still times out after 30 minutes. >>>>>> >>>>>> Scheduled time: 23-Jun-2022 23:00:00 >>>>>> Start time: 23-Jun-2022 23:00:00 >>>>>> End time: 23-Jun-2022 23:30:31 >>>>>> Elapsed time: 30 mins 31 secs >>>>>> FD termination status: Fatal Error >>>>>> SD termination status: Waiting on FD >>>>>> >>>>>> I don't know where else to add an increased timeout, please can someone >>>>>> tell me where I need to look to add this timeout increased figure. >>>>>> >>>>>> What is interesting is if I run the backup manually, it works fine and >>>>>> does it in under 30 minutes, but because the automatic schedule starts >>>>>> at 11pm every night, other jobs run at the same time, and so it takes >>>>>> longer to run it and hits this bizarre 30 minute timeout. >>>>>> >>>>>> Thanks in advance. > > -- > You received this message because you are subscribed to the Google Groups > "bareos-users" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/bareos-users/46a99a3a-8625-41bf-ba09-9fb96acf9a26n%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "bareos-users" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/bareos-users/B8B3D568-C785-4E17-A50B-63892AD1843B%40mlds-networks.com.
