You need to run bcharge first, this will put the device into 0004 mode instead of 0006 mode. FC7 might be screwing with the mode by running it's own bcharge code in a kernel module called berry_charge so make sure that's in your blacklist.
when you run bcharge just make sure your phone is listed as 0001 or 0004 as 0006 is SD Card only access mode. Best Regards, Martin Owens On 18/01/2008, Evilo Nod <[EMAIL PROTECTED]> wrote: > > > Hi. > > I just compiled and installed barry on a FC7 box without much trouble. > > However btool doesn't recognize any devices connected. > > from /proc/bus/usb/devices I see: > > T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 7 Spd=12 MxCh= 0 > D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1 > P: Vendor=0fca ProdID=0006 Rev= 1.06 > S: Manufacturer=Research In Motion > S: Product=RIM Mass Storage Device > S: SerialNumber=0E5F6E7C245CFF73A2CA068559FB0224217F914D > C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA > I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage > E: Ad=89(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms > E: Ad=0a(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms > > > and I even tried btool -B 3 -N 7 and still no luck. All I get is > [EMAIL PROTECTED] ~]$ btool > Blackberry devices found: > No device selected > > > When I plug the 8310 in I do get a system message: > > usb 3-2: new full speed USB device using uhci_hcd and address 7 > usb 3-2: configuration #1 chosen from 1 choice > scsi11 : SCSI emulation for USB Mass Storage devices > usb-storage: device found at 7 > usb-storage: waiting for device to settle before scanning > usb-storage: device scan complete > scsi 11:0:0:0: Direct-Access RIM BlackBerry SD 0001 PQ: 0 > ANSI: 4 CCS > sd 11:0:0:0: [sdd] Attached SCSI removable disk > sd 11:0:0:0: Attached scsi generic sg6 type 0 > usb 3-2: USB disconnect, address 7 > usb 3-2: new full speed USB device using uhci_hcd and address 8 > usb 3-2: configuration #1 chosen from 1 choice > scsi12 : SCSI emulation for USB Mass Storage devices > usb-storage: device found at 8 > usb-storage: waiting for device to settle before scanning > > > Why is it showing up as a scsi drive or a mass storage device. Is that > what I should see? > > Any help appreciated. > > Don > > > ------------------------------------------------------------------------- > This SF.net email is sponsored by: Microsoft > Defy all challenges. Microsoft(R) Visual Studio 2008. > http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ > _______________________________________________ > Barry-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/barry-devel > ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ Barry-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/barry-devel
