Hi!
I'm using bcm43xx with my iBook 1.42 Ghz. With 2.6.17.* it worked OK.
I upgraded to 2.6.18-rc2 and wireless stopped working.
What I get in dmesg is:
bcm43xx driver
PCI: Enabling device 0001:10:12.0 (0004 -> 0006)
usb 2-1: configuration #1 chosen from 1 choice
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001451fffe14041c]
usb 2-2: new full speed USB device using ohci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
snd-aoa-fabric-layout: found bus with layout 92
snd-aoa-fabric-layout: Using PMF GPIOs
pmf_gpio_set_lineout failed, rc: -19
snd-aoa-codec-tas: found tas3004
snd-aoa-fabric-layout: can use this codec
pmf_gpio_set_lineout failed, rc: -19
pmf_gpio_set_lineout failed, rc: -19
snd-aoa-codec-tas: tas found, addr 0x35 on
/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL
PROTECTED]
input: HID 05ac:1000 as /class/input/input4
input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0001:10:1a.0-1
input: HID 05ac:1000 as /class/input/input5
input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0001:10:1a.0-1
HID device not claimed by input or hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
input: appletouch as /class/input/input6
usbcore: registered new driver appletouch
Adding 524280k swap on /dev/hda5. Priority:-1 extents:1 across:524280k
adt746x: version 1 (supported)
adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: -1
sensor 0: PWR/MEMORY BOTTOMSIDE
sensor 1: CPU BOTTOMSIDE
sensor 2: GPU BOTTOMSIDE
adt746x: ADT7467 initializing
adt746x: Lowering max temperatures from 69, 92, 101 to 70, 50, 70
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
hda: Enabling Ultra DMA 5
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50 { LastFailedSense=0x05 }
ide: failed opcode was: unknown
hdc: Enabling MultiWord DMA 2
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1490:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1490:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1490:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1490:bcm43xx_find_lopair()
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Open Authentication completed with 00:0f:66:20:e8:6b
[drm] Initialized drm 1.0.1 20051102
[drm] Initialized radeon 1.25.0 20060524 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
SoftMAC: Authentication response received from 00:16:6f:13:d3:a9 but
no queue item exists.
SoftMAC: Authentication response received from 00:16:6f:13:d3:a9 but
no queue item exists.
SoftMAC: Authentication response received from 00:16:6f:13:d3:a9 but
no queue item exists.
SoftMAC: Authentication response received from 00:16:6f:13:d3:a9 but
no queue item exists.
SoftMAC: Authentication response received from 00:16:6f:13:d3:a9 but
no queue item exists.
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 3/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
SoftMAC: Authentication timed out with 00:0f:66:20:e8:6b
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: Radio turned off
bcm43xx: DMA 0x0200 (RX) max used slots: 1/64
bcm43xx: DMA 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA 0x0220 (TX) max used slots: 1/512
bcm43xx: DMA 0x0200 (TX) max used slots: 0/512
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
bcm43xx: Card IRQ register not responding. Giving up.
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
http://bat.berlios.de/mailman/listinfo/bcm43xx-dev
