On Sunday 24 September 2006 19:51, Christian wrote: > Hello, > > I use WPA with wpa_supplicant v0.5.5. > > ps -def | grep wpa > > root 5975 1 0 19:10 ? > 00:00:00 /sbin/wpa_supplicant -Dwext > -c/etc/wpa_supplicant/wpa_supplicant.conf -W -B -ieth1 > -P/var/run/wpa_supplicant-eth1.pid > root 5986 1 0 19:10 ? > 00:00:00 /bin/wpa_cli -a/etc/wpa_supplicant/wpa_cli.sh > -p/var/run/wpa_supplicant -ieth1 -P/var/run/wpa_cli-eth1.pid -B > root 6638 5986 0 19:46 ? > 00:00:00 /bin/sh /etc/wpa_supplicant/wpa_cli.sh eth1 CONNECTED > root 7030 7029 0 19:46 ? 00:00:00 /bin/wpa_cli -ieth1 status > > lspci: > > 06:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] > 802.11g Wireless LAN Controller (rev 02) > Subsystem: AMBIT Microsystem Corp. Aspire 3022WLMi, 5024WLMi > Flags: bus master, fast devsel, latency 64, IRQ 21 > Memory at c0304000 (32-bit, non-prefetchable) [size=8K] > > another dmeg output with the beginning: > > ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 21 (level, low) -> IRQ 21 > bcm43xx: Chip ID 0x4318, rev 0x2 > bcm43xx: Number of cores: 4 > bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled > bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, enabled > bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled > bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled > bcm43xx: PHY connected > bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7 > bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8) > bcm43xx: Radio turned off > bcm43xx: Radio turned off > bcm43xx: PHY connected > bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06) > bcm43xx: Radio turned on > bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: > drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair() > bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: > drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair() > bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: > drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair() > bcm43xx: Chip initialized > bcm43xx: 32-bit DMA initialized > bcm43xx: Keys cleared > bcm43xx: Selected 802.11 core (phytype 2) > bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: > drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair() > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Associate: failed to initiate scan. Is device up? > ADDRCONF(NETDEV_UP): eth1: link is not ready > SoftMAC: empty ratesinfo? > SoftMAC: empty ratesinfo? > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > SoftMAC: Scanning finished > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Unable to find matching network after scan! > SoftMAC: Scanning finished > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Scanning finished > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Scanning finished > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Scanning finished > SoftMAC: Unable to find matching network after scan! > SoftMAC: generic IE set to dd160050f20101000050f20201000050f20201000050f202 > SoftMAC: Associate: Scanning for networks first. > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e > SoftMAC: Cannot associate without being authenticated, requested > authentication > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e. > printk: 2 messages suppressed. > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e > SoftMAC: sent association request! > SoftMAC: Scanning finished > SoftMAC: sent association request! > SoftMAC: associated! > ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled = > 1, .encrypt = 1 > bcm43xx: set security called, .enabled = 1, .encrypt = 1 > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no queue > item exists. > SoftMAC: Authentication response received from 00:13:10:2f:98:3e but no queue > item exists. > > > Other information needed?
Do you have two APs in range? The log looks like two association processes are interfering and disturb each other. (There shouldn't be two assoc processes in the first place. That's a bug.) -- Greetings Michael. _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
