The card is an Asus WL-100GE
lspci output
06:00.0 0280: 14e4:4318 (rev 02)
Subsystem: 1043:100f
Flags: bus master, fast devsel, latency 64, IRQ 16
Memory at 34000000 (32-bit, non-prefetchable) [size=8K]
There seems to be some sort or radio initialization problem, it can't
connect to the access point unless the connection is reset. The
connection seems to work fine after that. This was done is the
following dmesg log
[ 0.000000] Linux version 2.6.21-rc5-custom2 ([EMAIL PROTECTED]) (gcc
version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #1 SMP Thu Apr 5 16:01:36 EST 2007
<snip>
[ 19.668000] pccard: CardBus card inserted into slot 0
[ 19.668000] PM: Adding info for pci:0000:06:00.0
[ 19.760000] cs: IO port probe 0x100-0x3af: clean.
[ 19.764000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 19.764000] cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f
[ 19.764000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07
0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
[ 19.764000] cs: IO port probe 0xa00-0xaff: clean.
[ 19.828000] ieee80211_crypt: registered algorithm 'NULL'
[ 19.856000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 19.856000] ieee80211: Copyright (C) 2004-2005 Intel Corporation
<[EMAIL PROTECTED]>
[ 19.960000] bcm43xx driver
[ 19.960000] PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
[ 19.960000] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 17 (level,
low) -> IRQ 16
[ 19.960000] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 19.968000] bcm43xx: Chip ID 0x4318, rev 0x2
[ 19.968000] bcm43xx: Number of cores: 4
[ 19.968000] bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243
[ 19.968000] bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243
[ 19.968000] bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243
[ 19.968000] bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243
[ 19.972000] bcm43xx: PHY connected
[ 19.972000] bcm43xx: Detected PHY: Analog: 3, Type 2, Revision 7
[ 19.972000] bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver:
2050 Rev: 8)
[ 19.972000] bcm43xx: Radio turned off
[ 19.972000] bcm43xx: Radio turned off
[ 19.972000] PM: Adding info for No Bus:eth1
[ 19.988000] bcm43xx: PHY connected
[ 19.988000] PM: Adding info for No Bus:0000:06:00.0
[ 20.032000] PM: Removing info for No Bus:0000:06:00.0
[ 20.032000] PM: Adding info for No Bus:0000:06:00.0
[ 20.036000] PM: Removing info for No Bus:0000:06:00.0
[ 20.036000] PM: Adding info for No Bus:0000:06:00.0
[ 20.052000] PM: Removing info for No Bus:0000:06:00.0
[ 20.052000] PM: Adding info for No Bus:0000:06:00.0
[ 20.056000] PM: Removing info for No Bus:0000:06:00.0
[ 20.116000] bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
[ 20.124000] bcm43xx: Radio turned on
[ 20.124000] bcm43xx: Radio enabled by hardware
[ 20.140000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 20.292000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 20.296000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 20.296000] bcm43xx: Chip initialized
[ 20.296000] bcm43xx: 32-bit DMA initialized
[ 20.296000] bcm43xx: Keys cleared
[ 20.296000] bcm43xx: Selected 802.11 core (phytype 2)
[ 20.296000] PM: Adding info for No Bus:hw_random
[ 20.304000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 20.528000] fuse init (API version 7.8)
[ 20.528000] PM: Adding info for No Bus:fuse
[ 20.620000] lp: driver loaded but no devices found
[ 20.652000] Adding 1317288k swap on
/dev/disk/by-uuid/a7087cad-5a7a-4892-85be-b9f7d9d44232. Priority:-1
extents:1 across:1317288k
[ 20.828000] EXT3 FS on hda1, internal journal
[ 25.108000] PM: Adding info for No Bus:vcs4
[ 25.108000] PM: Adding info for No Bus:vcsa4
[ 25.108000] PM: Adding info for No Bus:vcs5
[ 25.108000] PM: Adding info for No Bus:vcsa5
[ 25.112000] PM: Adding info for No Bus:vcs2
[ 25.112000] PM: Adding info for No Bus:vcsa2
[ 25.112000] PM: Adding info for No Bus:vcs3
[ 25.112000] PM: Adding info for No Bus:vcsa3
[ 25.124000] PM: Adding info for No Bus:vcs6
[ 25.124000] PM: Adding info for No Bus:vcsa6
[ 25.344000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 25.360000] ibm_acpi: ec object not found
[ 25.460000] ACPI: Battery Slot [BAT1] (battery present)
[ 25.488000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 25.504000] ACPI: AC Adapter [ACAD] (on-line)
[ 25.580000] No dock devices found.
[ 25.636000] input: Power Button (FF) as /class/input/input4
[ 25.652000] ACPI: Power Button (FF) [PWRF]
[ 25.692000] input: Power Button (CM) as /class/input/input5
[ 25.704000] ACPI: Power Button (CM) [PWRB]
[ 25.748000] input: Sleep Button (CM) as /class/input/input6
[ 25.760000] ACPI: Sleep Button (CM) [SLPB]
[ 25.800000] input: Lid Switch as /class/input/input7
[ 25.816000] ACPI: Lid Switch [LID]
[ 26.304000] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor
3000+ processors (version 2.00.00)
[ 26.304000] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0xa
[ 26.304000] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xc
[ 26.304000] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x13
[ 28.480000] tsdev (compaq touchscreen emulation) is scheduled for
removal.
[ 28.480000] See Documentation/feature-removal-schedule.txt for details.
[ 28.640000] tsdev (compaq touchscreen emulation) is scheduled for
removal.
[ 28.640000] See Documentation/feature-removal-schedule.txt for details.
[ 30.404000] Capability LSM initialized
[ 30.556000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 30.724000] SoftMAC: Open Authentication completed with 00:40:05:5a:8f:9f
[ 31.444000] PM: Adding info for No Bus:vcs7
[ 31.444000] PM: Adding info for No Bus:vcsa7
[ 31.668000] PM: Removing info for No Bus:vcs7
[ 31.668000] PM: Removing info for No Bus:vcsa7
[ 31.744000] PM: Adding info for No Bus:vcs7
[ 31.744000] PM: Adding info for No Bus:vcsa7
[ 33.024000] ppdev: user-space parallel port driver
[ 37.500000] NET: Registered protocol family 10
[ 37.504000] lo: Disabled Privacy Extensions
[ 37.504000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 38.924000] apm: BIOS not found.
[ 39.204000] Bluetooth: Core ver 2.11
[ 39.204000] PM: Adding info for platform:bluetooth
[ 39.204000] NET: Registered protocol family 31
[ 39.204000] Bluetooth: HCI device and connection manager initialized
[ 39.204000] Bluetooth: HCI socket layer initialized
[ 39.272000] Bluetooth: L2CAP ver 2.8
[ 39.272000] Bluetooth: L2CAP socket layer initialized
[ 39.416000] Bluetooth: RFCOMM socket layer initialized
[ 39.416000] Bluetooth: RFCOMM TTY layer initialized
[ 39.416000] Bluetooth: RFCOMM ver 1.8
[ 43.200000] Clocksource tsc unstable (delta = -80060859 ns)
[ 47.664000] eth1: no IPv6 routers present
[ 59.212000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 59.212000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 59.212000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 59.212000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 70.348000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 70.364000] PM: Removing info for No Bus:hw_random
[ 70.364000] bcm43xx: Radio turned off
[ 70.364000] bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64
[ 70.364000] bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
[ 70.364000] bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
[ 70.364000] bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
[ 70.364000] bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
[ 70.364000] bcm43xx: DMA-32 0x0220 (TX) max used slots: 2/512
[ 70.364000] bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
[ 70.368000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 72.036000] PM: Adding info for No Bus:0000:06:00.0
[ 72.040000] PM: Removing info for No Bus:0000:06:00.0
[ 72.044000] PM: Adding info for No Bus:0000:06:00.0
[ 72.052000] PM: Removing info for No Bus:0000:06:00.0
[ 72.052000] PM: Adding info for No Bus:0000:06:00.0
[ 72.064000] PM: Removing info for No Bus:0000:06:00.0
[ 72.064000] PM: Adding info for No Bus:0000:06:00.0
[ 72.068000] PM: Removing info for No Bus:0000:06:00.0
[ 72.128000] bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
[ 72.136000] bcm43xx: Radio turned on
[ 72.136000] bcm43xx: Radio enabled by hardware
[ 72.152000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 72.316000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 72.320000] bcm43xx: Chip initialized
[ 72.320000] bcm43xx: 32-bit DMA initialized
[ 72.320000] bcm43xx: Keys cleared
[ 72.320000] bcm43xx: Selected 802.11 core (phytype 2)
[ 72.320000] PM: Adding info for No Bus:hw_random
[ 72.328000] bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1477:bcm43xx_find_lopair()
[ 72.340000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 72.480000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 72.480000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 72.480000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 72.480000] bcm43xx: set security called, .level = 0, .enabled = 0,
.encrypt = 0
[ 72.488000] SoftMAC: Open Authentication completed with 00:40:05:5a:8f:9f
[ 72.496000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Good luck
Brian
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
