Patch 4 of 6.
The b43 driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <[EMAIL PROTECTED]>
---
Index: wireless-2.6/drivers/net/wireless/b43/leds.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/leds.c
+++ wireless-2.6/drivers/net/wireless/b43/leds.c
@@ -187,10 +187,10 @@ void b43_leds_init(struct b43_wldev *dev
enum b43_led_behaviour behaviour;
bool activelow;
- sprom[0] = bus->sprom.r1.gpio0;
- sprom[1] = bus->sprom.r1.gpio1;
- sprom[2] = bus->sprom.r1.gpio2;
- sprom[3] = bus->sprom.r1.gpio3;
+ sprom[0] = bus->sprom.gpio0;
+ sprom[1] = bus->sprom.gpio1;
+ sprom[2] = bus->sprom.gpio2;
+ sprom[3] = bus->sprom.gpio3;
for (i = 0; i < 4; i++) {
if (sprom[i] == 0xFF) {
Index: wireless-2.6/drivers/net/wireless/b43/lo.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/lo.c
+++ wireless-2.6/drivers/net/wireless/b43/lo.c
@@ -264,8 +264,8 @@ static u16 lo_measure_feedthrough(struct
rfover |= pga;
rfover |= lna;
rfover |= trsw_rx;
- if ((dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) &&
- phy->rev > 6)
+ if ((dev->dev->bus->sprom.boardflags_lo & B43_BFL_EXTLNA)
+ && phy->rev > 6)
rfover |= B43_PHY_RFOVERVAL_EXTLNA;
b43_phy_write(dev, B43_PHY_PGACTL, 0xE300);
@@ -634,7 +634,7 @@ static void lo_measure_setup(struct b43_
& 0xFFFC);
if (phy->type == B43_PHYTYPE_G) {
if ((phy->rev >= 7) &&
- (sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) {
+ (sprom->boardflags_lo & B43_BFL_EXTLNA)) {
b43_phy_write(dev, B43_PHY_RFOVER, 0x933);
} else {
b43_phy_write(dev, B43_PHY_RFOVER, 0x133);
Index: wireless-2.6/drivers/net/wireless/b43/main.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/main.c
+++ wireless-2.6/drivers/net/wireless/b43/main.c
@@ -1924,7 +1924,7 @@ static int b43_gpio_init(struct b43_wlde
mask |= 0x0180;
set |= 0x0180;
}
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL) {
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL) {
b43_write16(dev, B43_MMIO_GPIO_MASK,
b43_read16(dev, B43_MMIO_GPIO_MASK)
| 0x0200);
@@ -2289,7 +2289,7 @@ static void b43_periodic_every60sec(stru
if (!b43_has_hardware_pctl(phy))
b43_lo_g_ctl_mark_all_unused(dev);
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) {
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) {
b43_mac_suspend(dev);
b43_calc_nrssi_slope(dev);
if ((phy->radio_ver == 0x2050) && (phy->radio_rev == 8)) {
@@ -3208,13 +3208,13 @@ static void b43_bluetooth_coext_enable(s
struct ssb_sprom *sprom = &dev->dev->bus->sprom;
u32 hf;
- if (!(sprom->r1.boardflags_lo & B43_BFL_BTCOEXIST))
+ if (!(sprom->boardflags_lo & B43_BFL_BTCOEXIST))
return;
if (dev->phy.type != B43_PHYTYPE_B && !dev->phy.gmode)
return;
hf = b43_hf_read(dev);
- if (sprom->r1.boardflags_lo & B43_BFL_BTCMOD)
+ if (sprom->boardflags_lo & B43_BFL_BTCMOD)
hf |= B43_HF_BTCOEXALT;
else
hf |= B43_HF_BTCOEX;
@@ -3348,7 +3348,7 @@ static int b43_wireless_core_init(struct
hf |= B43_HF_SYMW;
if (phy->rev == 1)
hf |= B43_HF_GDCW;
- if (sprom->r1.boardflags_lo & B43_BFL_PACTRL)
+ if (sprom->boardflags_lo & B43_BFL_PACTRL)
hf |= B43_HF_OFDMPABOOST;
} else if (phy->type == B43_PHYTYPE_B) {
hf |= B43_HF_SYMW;
@@ -3859,20 +3859,20 @@ static void b43_sprom_fixup(struct ssb_b
/* boardflags workarounds */
if (bus->boardinfo.vendor == SSB_BOARDVENDOR_DELL &&
bus->chip_id == 0x4301 && bus->boardinfo.rev == 0x74)
- bus->sprom.r1.boardflags_lo |= B43_BFL_BTCOEXIST;
+ bus->sprom.boardflags_lo |= B43_BFL_BTCOEXIST;
if (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE &&
bus->boardinfo.type == 0x4E && bus->boardinfo.rev > 0x40)
- bus->sprom.r1.boardflags_lo |= B43_BFL_PACTRL;
+ bus->sprom.boardflags_lo |= B43_BFL_PACTRL;
/* Handle case when gain is not set in sprom */
- if (bus->sprom.r1.antenna_gain_a == 0xFF)
- bus->sprom.r1.antenna_gain_a = 2;
- if (bus->sprom.r1.antenna_gain_bg == 0xFF)
- bus->sprom.r1.antenna_gain_bg = 2;
+ if (bus->sprom.antenna_gain_a == 0xFF)
+ bus->sprom.antenna_gain_a = 2;
+ if (bus->sprom.antenna_gain_bg == 0xFF)
+ bus->sprom.antenna_gain_bg = 2;
/* Convert Antennagain values to Q5.2 */
- bus->sprom.r1.antenna_gain_a <<= 2;
- bus->sprom.r1.antenna_gain_bg <<= 2;
+ bus->sprom.antenna_gain_a <<= 2;
+ bus->sprom.antenna_gain_bg <<= 2;
}
static void b43_wireless_exit(struct ssb_device *dev, struct b43_wl *wl)
@@ -3905,10 +3905,10 @@ static int b43_wireless_init(struct ssb_
hw->max_noise = -110;
hw->queues = 1; /* FIXME: hardware has more queues */
SET_IEEE80211_DEV(hw, dev->dev);
- if (is_valid_ether_addr(sprom->r1.et1mac))
- SET_IEEE80211_PERM_ADDR(hw, sprom->r1.et1mac);
+ if (is_valid_ether_addr(sprom->et1mac))
+ SET_IEEE80211_PERM_ADDR(hw, sprom->et1mac);
else
- SET_IEEE80211_PERM_ADDR(hw, sprom->r1.il0mac);
+ SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac);
/* Get and initialize struct b43_wl */
wl = hw_to_b43_wl(hw);
Index: wireless-2.6/drivers/net/wireless/b43/phy.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/phy.c
+++ wireless-2.6/drivers/net/wireless/b43/phy.c
@@ -1139,7 +1139,7 @@ static void b43_phy_inita(struct b43_wld
} else {
b43_phy_setupg(dev);
if (phy->gmode &&
- (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL))
+ (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL))
b43_phy_write(dev, 0x046E, 0x03CF);
return;
}
@@ -1286,7 +1286,7 @@ static void b43_phy_initb4(struct b43_wl
if (phy->radio_ver == 0x2050)
b43_phy_write(dev, 0x002A, 0x88C2);
b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt, phy->tx_control);
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) {
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) {
b43_calc_nrssi_slope(dev);
b43_calc_nrssi_threshold(dev);
}
@@ -1433,7 +1433,7 @@ static void b43_phy_initb6(struct b43_wl
b43_radio_write16(dev, 0x5A, 0x88);
b43_radio_write16(dev, 0x5B, 0x6B);
b43_radio_write16(dev, 0x5C, 0x0F);
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_ALTIQ) {
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_ALTIQ) {
b43_radio_write16(dev, 0x5D, 0xFA);
b43_radio_write16(dev, 0x5E, 0xD8);
} else {
@@ -1525,7 +1525,7 @@ static void b43_phy_initb6(struct b43_wl
b43_phy_write(dev, 0x0062, 0x0007);
b43_radio_init2050(dev);
b43_lo_g_measure(dev);
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) {
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) {
b43_calc_nrssi_slope(dev);
b43_calc_nrssi_threshold(dev);
}
@@ -1645,7 +1645,7 @@ static void b43_calc_loopback_gain(struc
b43_phy_write(dev, B43_PHY_RFOVERVAL,
b43_phy_read(dev, B43_PHY_RFOVERVAL) & 0xCFFF);
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) {
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_EXTLNA) {
if (phy->rev >= 7) {
b43_phy_write(dev, B43_PHY_RFOVER,
b43_phy_read(dev, B43_PHY_RFOVER)
@@ -1812,7 +1812,7 @@ static void b43_phy_initg(struct b43_wld
& 0x0FFF) | (phy->lo_control->
tx_bias << 12));
}
- if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL)
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL)
b43_phy_write(dev, B43_PHY_BASE(0x2E), 0x8075);
else
b43_phy_write(dev, B43_PHY_BASE(0x2E), 0x807F);
@@ -1826,7 +1826,7 @@ static void b43_phy_initg(struct b43_wld
b43_phy_write(dev, B43_PHY_LO_MASK, 0x8078);
}
- if (!(dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI)) {
+ if (!(dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI)) {
/* The specs state to update the NRSSI LT with
* the value 0x7FFFFFFF here. I think that is some weird
* compiler optimization in the original driver.
@@ -2036,16 +2036,15 @@ void b43_phy_xmitpower(struct b43_wldev
estimated_pwr =
b43_phy_estimate_power_out(dev, average);
- max_pwr = dev->dev->bus->sprom.r1.maxpwr_bg;
- if ((dev->dev->bus->sprom.r1.
- boardflags_lo & B43_BFL_PACTRL)
- && (phy->type == B43_PHYTYPE_G))
+ max_pwr = dev->dev->bus->sprom.maxpwr_bg;
+ if ((dev->dev->bus->sprom.boardflags_lo
+ & B43_BFL_PACTRL) && (phy->type == B43_PHYTYPE_G))
max_pwr -= 0x3;
if (unlikely(max_pwr <= 0)) {
b43warn(dev->wl,
"Invalid max-TX-power value in
SPROM.\n");
max_pwr = 60; /* fake it */
- dev->dev->bus->sprom.r1.maxpwr_bg = max_pwr;
+ dev->dev->bus->sprom.maxpwr_bg = max_pwr;
}
/*TODO:
@@ -2103,7 +2102,7 @@ void b43_phy_xmitpower(struct b43_wldev
B43_TXCTL_TXMIX;
rfatt += 2;
bbatt += 2;
- } else if (dev->dev->bus->sprom.r1.
+ } else if (dev->dev->bus->sprom.
boardflags_lo &
B43_BFL_PACTRL) {
bbatt += 4 * (rfatt - 2);
@@ -2179,13 +2178,13 @@ int b43_phy_init_tssi2dbm_table(struct b
s8 *dyn_tssi2dbm;
if (phy->type == B43_PHYTYPE_A) {
- pab0 = (s16) (dev->dev->bus->sprom.r1.pa1b0);
- pab1 = (s16) (dev->dev->bus->sprom.r1.pa1b1);
- pab2 = (s16) (dev->dev->bus->sprom.r1.pa1b2);
+ pab0 = (s16) (dev->dev->bus->sprom.pa1b0);
+ pab1 = (s16) (dev->dev->bus->sprom.pa1b1);
+ pab2 = (s16) (dev->dev->bus->sprom.pa1b2);
} else {
- pab0 = (s16) (dev->dev->bus->sprom.r1.pa0b0);
- pab1 = (s16) (dev->dev->bus->sprom.r1.pa0b1);
- pab2 = (s16) (dev->dev->bus->sprom.r1.pa0b2);
+ pab0 = (s16) (dev->dev->bus->sprom.pa0b0);
+ pab1 = (s16) (dev->dev->bus->sprom.pa0b1);
+ pab2 = (s16) (dev->dev->bus->sprom.pa0b2);
}
if ((dev->dev->bus->chip_id == 0x4301) && (phy->radio_ver != 0x2050)) {
@@ -2198,17 +2197,17 @@ int b43_phy_init_tssi2dbm_table(struct b
pab0 != -1 && pab1 != -1 && pab2 != -1) {
/* The pabX values are set in SPROM. Use them. */
if (phy->type == B43_PHYTYPE_A) {
- if ((s8) dev->dev->bus->sprom.r1.itssi_a != 0 &&
- (s8) dev->dev->bus->sprom.r1.itssi_a != -1)
+ if ((s8) dev->dev->bus->sprom.itssi_a != 0 &&
+ (s8) dev->dev->bus->sprom.itssi_a != -1)
phy->tgt_idle_tssi =
- (s8) (dev->dev->bus->sprom.r1.itssi_a);
+ (s8) (dev->dev->bus->sprom.itssi_a);
else
phy->tgt_idle_tssi = 62;
} else {
- if ((s8) dev->dev->bus->sprom.r1.itssi_bg != 0 &&
- (s8) dev->dev->bus->sprom.r1.itssi_bg != -1)
+ if ((s8) dev->dev->bus->sprom.itssi_bg != 0 &&
+ (s8) dev->dev->bus->sprom.itssi_bg != -1)
phy->tgt_idle_tssi =
- (s8) (dev->dev->bus->sprom.r1.itssi_bg);
+ (s8) (dev->dev->bus->sprom.itssi_bg);
else
phy->tgt_idle_tssi = 62;
}
@@ -3114,7 +3113,7 @@ void b43_calc_nrssi_threshold(struct b43
if (phy->radio_ver != 0x2050)
return;
if (!
- (dev->dev->bus->sprom.r1.
+ (dev->dev->bus->sprom.
boardflags_lo & B43_BFL_RSSI))
return;
@@ -3145,7 +3144,7 @@ void b43_calc_nrssi_threshold(struct b43
}
case B43_PHYTYPE_G:
if (!phy->gmode ||
- !(dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI)) {
+ !(dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI)) {
tmp16 = b43_nrssi_hw_read(dev, 0x20);
if (tmp16 >= 0x20)
tmp16 -= 0x40;
@@ -3667,7 +3666,7 @@ static u16 radio2050_rfover_val(struct b
}
if ((phy->rev < 7) ||
- !(sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) {
+ !(sprom->boardflags_lo & B43_BFL_EXTLNA)) {
if (phy_register == B43_PHY_RFOVER) {
return 0x1B3;
} else if (phy_register == B43_PHY_RFOVERVAL) {
@@ -3707,7 +3706,7 @@ static u16 radio2050_rfover_val(struct b
}
} else {
if ((phy->rev < 7) ||
- !(sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) {
+ !(sprom->boardflags_lo & B43_BFL_EXTLNA)) {
if (phy_register == B43_PHY_RFOVER) {
return 0x1B3;
} else if (phy_register == B43_PHY_RFOVERVAL) {
@@ -4186,7 +4185,7 @@ int b43_radio_selectchannel(struct b43_w
b43_write16(dev, B43_MMIO_CHANNEL, channel2freq_bg(channel));
if (channel == 14) {
- if (dev->dev->bus->sprom.r1.country_code ==
+ if (dev->dev->bus->sprom.country_code ==
SSB_SPROM1CCODE_JAPAN)
b43_hf_write(dev,
b43_hf_read(dev) & ~B43_HF_ACPR);
Index: wireless-2.6/drivers/net/wireless/b43/xmit.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/xmit.c
+++ wireless-2.6/drivers/net/wireless/b43/xmit.c
@@ -385,7 +385,7 @@ static s8 b43_rssi_postprocess(struct b4
else
tmp -= 3;
} else {
- if (dev->dev->bus->sprom.r1.
+ if (dev->dev->bus->sprom.
boardflags_lo & B43_BFL_RSSI) {
if (in_rssi > 63)
in_rssi = 63;
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
