Hi,
i just can't get my wlan work properly on my extensa 5220.
Here's a bunch of information about my notebook.
uname -r
2.6.24-8-generic
lspci | grep -i netw
04:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI
(rev 01)
dmesg | grep b43
[ 34.924306] b43-phy0: Broadcom 4311 WLAN found
[ 40.414718] input: b43-phy0 as /devices/virtual/input/input9
[ 42.491768] Registered led device: b43-phy0:tx
[ 42.491789] Registered led device: b43-phy0:rx
[ 42.491806] Registered led device: b43-phy0:radio
dmesg | grep -i wlan
[ 34.924306] b43-phy0: Broadcom 4311 WLAN found
[ 51.908877] ADDRCONF(NETDEV_UP): wlan0: link is not ready
ifconfig
eth0 Protokoll:Ethernet Hardware Adresse 00:1D:72:0C:BD:FB
inet Adresse:192.168.123.101 Bcast:192.168.123.255 Maske:
255.255.255.0
inet6 Adresse: fe80::21d:72ff:fe0c:bdfb/64
Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9667 errors:0 dropped:0 overruns:0 frame:0
TX packets:5021 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:12138424 (11.5 MB) TX bytes:580582 (566.9 KB)
Interrupt:16
lo Protokoll:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Protokoll:Ethernet Hardware Adresse 00:1E:4C:4E:15:14
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wmaster0 Protokoll:UNSPEC Hardware Adresse
00-1E-4C-4E-15-14-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment thr=2346 B
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
irda0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:C0:49:E3:59:B6
ESSID:"HONOLULU"
Mode:Master
Channel:8
Frequency:2.447 GHz (Channel 8)
Quality=90/100 Signal level=-45 dBm Noise level=-67
dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s
6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s
36 Mb/s; 48 Mb/s; 54 Mb/s
Extra:tsf=000000b5c96d4121
cat /etc/network/interfaces
auto lo
iface lo inet loopback
address 127.0.0.1
netmask 255.0.0.0
iface wlan0 inet dhcp
wireless-rate 11M
wireless-essid HONOLULU
cat /etc/udev/rules.d/70-persistent-net.rules
# This file maintains persistent names for network interfaces.
# See udev(7) for syntax.
#
# Entries are automatically added by the 75-persistent-net-generator.rules
# file; however you are also free to add your own entries.
# PCI device 0x14e4:0x1693 (tg3)
SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:1d:72:0c:bd:fb",
NAME="eth0"
# PCI device 0x14e4:0x4311 (b43-pci-bridge)
SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:1e:4c:4e:15:14",
ATTRS{type}=="1", NAME="wlan0"
sudo dhclient wlan0
There is already a pid file /var/run/dhclient.pid with pid 134519120
Internet Systems Consortium DHCP Client V3.0.5
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
wmaster0: unknown hardware address type 801
wmaster0: unknown hardware address type 801
Listening on LPF/wlan0/00:1e:4c:4e:15:14
Sending on LPF/wlan0/00:1e:4c:4e:15:14
Sending on Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
Any ideas, why dhcp doesn't work and what i can do to make it work ?
Peter
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
