Hello,
Since I switched to the b43legacy driver, after ndiswrapper stopped
working, I've managed to make wireless work again, but it seems to be
quite slow, or connections sometimes fail, and messages are issued
about once every second (see attachment enabled-disabled.txt).
It also prevents me from using keyboard repetition, as if each event
acted as pressing a key, stopping the repetition sequence.
The output of uname, lspci and dmesg is in attachment info.txt.
I have tried to have a look at the driver code, and all I found was
where the message was. But I couldn't find where the event comes from.
Or I didn't have the courage to look for it, as I don't have any kernel
programming experience.
Anyway, my Asus L5800C has no hardware rfkill switch, at least none of
the buttons acted like one when I used ndiswrapper. I'm wondering what
the state change every second (with each polling) means.
Could you please help me ? I'd be glad to try a patch if you tell me
what to change.
--
Jorge Van Hemelryck
Oct 5 23:59:04 frigate kernel: b43legacy-phy0: Radio hardware status changed
to ENABLED
Oct 5 23:59:06 frigate kernel: b43legacy-phy0: Radio hardware status changed
to DISABLED
Oct 5 23:59:07 frigate kernel: b43legacy-phy0: Radio hardware status changed
to ENABLED
Oct 5 23:59:08 frigate kernel: b43legacy-phy0: Radio hardware status changed
to DISABLED
Oct 5 23:59:09 frigate kernel: b43legacy-phy0: Radio hardware status changed
to ENABLED
Oct 5 23:59:10 frigate kernel: b43legacy-phy0: Radio hardware status changed
to DISABLED
Oct 5 23:59:11 frigate kernel: b43legacy-phy0: Radio hardware status changed
to ENABLED
Oct 5 23:59:12 frigate kernel: b43legacy-phy0: Radio hardware status changed
to DISABLED
Oct 5 23:59:13 frigate kernel: b43legacy-phy0: Radio hardware status changed
to ENABLED
Oct 5 23:59:18 frigate kernel: b43legacy-phy0: Radio hardware status changed
to DISABLED
$ uname -a
Linux frigate 2.6.27-desktop-1mnb #1 SMP Fri Oct 10 15:59:59 EDT 2008 i686
Intel(R) Pentium(R) 4 CPU 2.66GHz GNU/Linux
$ sudo lspci -vvn|grep 430 -A12
00:0c.0 0280: 14e4:4301 (rev 02)
Subsystem: 1043:0120
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
$ dmesg
Linux version 2.6.27-desktop-1mnb ([EMAIL PROTECTED]) (gcc version 4.3.2 (GCC)
) #1 SMP Fri Oct 10 15:59:59 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fffa000 (usable)
BIOS-e820: 000000003fffa000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
last_pfn = 0x3fffa max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 38000000 @ 7000-c000
RAMDISK: 03c95000 - 040efe6b
DMI 2.3 present.
ACPI: RSDP 000F6410, 0014 (r0 ASUS )
ACPI: RSDT 3FFFA000, 0030 (r1 ASUS L5C 42302E31 MSFT 31313031)
ACPI: FACP 3FFFA0B6, 0074 (r1 ASUS L5C 42302E31 MSFT 31313031)
ACPI: DSDT 3FFFA12A, 4016 (r1 ASUS L5C 1000 MSFT 100000E)
ACPI: FACS 3FFFF000, 0040
ACPI: BOOT 3FFFA030, 0028 (r1 ASUS L5C 42302E31 MSFT 31313031)
ACPI: APIC 3FFFA058, 0050 (r1 ASUS L5C 42302E31 MSFT 31313031)
127MB HIGHMEM available.
896MB LOWMEM available.
mapped low ram: 0 - 38000000
low ram: 00000000 - 38000000
bootmap 00008000 - 0000f000
(9 early reservations) ==> bootmem [0000000000 - 0038000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 0000590800] TEXT DATA BSS ==> [0000100000 - 0000590800]
#4 [0003c95000 - 00040efe6b] RAMDISK ==> [0003c95000 - 00040efe6b]
#5 [0000591000 - 0000594000] INIT_PG_TABLE ==> [0000591000 - 0000594000]
#6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00038000
HighMem 0x00038000 -> 0x0003fffa
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0003fffa
On node 0 totalpages: 262041
free_area_init_node: node 0, pgdat c049b000, node_mem_map c1000000
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 32506 pages, LIFO batch:7
ACPI: PM-Timer IO Port: 0xe408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 1 CPUs, 0 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
PERCPU: Allocating 40988 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 1, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259993
Kernel command line: BOOT_IMAGE=linux root=LABEL=/ resume=LABEL=swap
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PMTIMER calibration value
Detected 2666.749 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029468k/1048552k available (2576k kernel code, 18220k reserved, 1206k
data, 364k init, 131048k highmem)
virtual kernel memory layout:
fixmap : 0xffe18000 - 0xfffff000 (1948 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04b8000 - 0xc0513000 ( 364 kB)
.data : 0xc0384006 - 0xc04b1a00 (1206 kB)
.text : 0xc0100000 - 0xc0384006 (2576 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency..
5333.49 BogoMIPS (lpj=2666749)
Security Framework initialized
AppArmor: AppArmor disabled by boottime parameter
Mount-cache hash table entries: 512
Hook version: 2.6.27-2.3 2008/08/29
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
Early unpacking initramfs... done
Freeing initrd memory: 4459k freed
ACPI: Core revision 20080609
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09
Brought up 1 CPUs
Total of 1 processors activated (5333.49 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0 level CPU
groups: 0
net_namespace: 840 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf1670, last bus=1
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:00.0 reg 10 32bit mmio: [e8000000, ebffffff]
pci 0000:00:02.0: Enabling SiS 96x SMBus
PCI: 0000:00:02.1 reg 20 io port: [e800, e81f]
PCI: 0000:00:02.3 reg 10 32bit mmio: [e7000000, e7000fff]
PCI: 0000:00:02.3 reg 30 32bit mmio: [0, 1ffff]
pci 0000:00:02.3: supports D1
pci 0000:00:02.3: supports D2
pci 0000:00:02.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.3: PME# disabled
PCI: 0000:00:02.5 reg 20 io port: [b800, b80f]
pci 0000:00:02.5: PME# supported from D3cold
pci 0000:00:02.5: PME# disabled
PCI: 0000:00:02.6 reg 10 io port: [b400, b4ff]
PCI: 0000:00:02.6 reg 14 io port: [b000, b07f]
pci 0000:00:02.6: supports D1
pci 0000:00:02.6: supports D2
pci 0000:00:02.6: PME# supported from D3hot D3cold
pci 0000:00:02.6: PME# disabled
PCI: 0000:00:02.7 reg 10 io port: [a800, a8ff]
PCI: 0000:00:02.7 reg 14 io port: [a400, a47f]
pci 0000:00:02.7: supports D1
pci 0000:00:02.7: supports D2
pci 0000:00:02.7: PME# supported from D3hot D3cold
pci 0000:00:02.7: PME# disabled
PCI: 0000:00:03.0 reg 10 32bit mmio: [e6800000, e6800fff]
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
PCI: 0000:00:03.1 reg 10 32bit mmio: [e6000000, e6000fff]
pci 0000:00:03.1: PME# supported from D0 D3hot D3cold
pci 0000:00:03.1: PME# disabled
PCI: 0000:00:03.2 reg 10 32bit mmio: [e5800000, e5800fff]
pci 0000:00:03.2: PME# supported from D0 D3hot D3cold
pci 0000:00:03.2: PME# disabled
PCI: 0000:00:03.3 reg 10 32bit mmio: [e5000000, e5000fff]
pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
pci 0000:00:03.3: PME# disabled
PCI: 0000:00:0a.0 reg 10 32bit mmio: [0, fff]
pci 0000:00:0a.0: supports D1
pci 0000:00:0a.0: supports D2
pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0a.0: PME# disabled
PCI: 0000:00:0a.1 reg 10 32bit mmio: [0, fff]
pci 0000:00:0a.1: supports D1
pci 0000:00:0a.1: supports D2
pci 0000:00:0a.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0a.1: PME# disabled
PCI: 0000:00:0a.2 reg 10 io port: [9800, 987f]
pci 0000:00:0a.2: supports D1
pci 0000:00:0a.2: supports D2
pci 0000:00:0a.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0a.2: PME# disabled
PCI: 0000:00:0c.0 reg 10 32bit mmio: [e4000000, e4001fff]
pci 0000:00:0c.0: supports D1
pci 0000:00:0c.0: supports D2
pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0c.0: PME# disabled
PCI: 0000:00:0d.0 reg 10 32bit mmio: [e3800000, e3803fff]
PCI: 0000:00:0d.0 reg 14 io port: [9400, 94ff]
pci 0000:00:0d.0: supports D1
pci 0000:00:0d.0: supports D2
pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0d.0: PME# disabled
PCI: 0000:01:00.0 reg 10 32bit mmio: [f0000000, f7ffffff]
PCI: 0000:01:00.0 reg 14 io port: [d800, d8ff]
PCI: 0000:01:00.0 reg 18 32bit mmio: [e7800000, e780ffff]
PCI: 0000:01:00.0 reg 30 32bit mmio: [effe0000, efffffff]
pci 0000:01:00.0: supports D1
pci 0000:01:00.0: supports D2
PCI: bridge 0000:00:01.0 io port: [d000, dfff]
PCI: bridge 0000:00:01.0 32bit mmio: [e7800000, e7ffffff]
PCI: bridge 0000:00:01.0 32bit mmio pref: [eff00000, febfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 11 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: Power Resource [FN0] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x3fffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec000ff could not be reserved
system 00:02: ioport range 0xe400-0xe47f has been reserved
system 00:02: ioport range 0xe480-0xe4ff has been reserved
system 00:02: ioport range 0xe800-0xe81f has been reserved
system 00:02: ioport range 0x480-0x48f has been reserved
system 00:02: iomem range 0xffee0000-0xffefffff has been reserved
system 00:03: iomem range 0xfffe0000-0xffffffff could not be reserved
system 00:04: ioport range 0x4d0-0x4d1 has been reserved
system 00:04: ioport range 0x800-0x87f has been reserved
system 00:04: ioport range 0x880-0x88f has been reserved
system 00:0f: ioport range 0x3f0-0x3f1 has been reserved
system 00:0f: ioport range 0x290-0x297 has been reserved
system 00:0f: ioport range 0x500-0x507 has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0xd000-0xdfff
pci 0000:00:01.0: MEM window: 0xe7800000-0xe7ffffff
pci 0000:00:01.0: PREFETCH window: 0x000000eff00000-0x000000febfffff
pci 0000:00:0a.0: CardBus bridge, secondary bus 0000:02
pci 0000:00:0a.0: IO window: 0x001000-0x0010ff
pci 0000:00:0a.0: IO window: 0x001400-0x0014ff
pci 0000:00:0a.0: PREFETCH window: 0x50000000-0x53ffffff
pci 0000:00:0a.0: MEM window: 0x54000000-0x57ffffff
pci 0000:00:0a.1: CardBus bridge, secondary bus 0000:06
pci 0000:00:0a.1: IO window: 0x001800-0x0018ff
pci 0000:00:0a.1: IO window: 0x001c00-0x001cff
pci 0000:00:0a.1: PREFETCH window: 0x58000000-0x5bffffff
pci 0000:00:0a.1: MEM window: 0x5c000000-0x5fffffff
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:0a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:0a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [d000, dfff]
bus: 01 index 1 mmio: [e7800000, e7ffffff]
bus: 01 index 2 mmio: [eff00000, febfffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [1000, 10ff]
bus: 02 index 1 io port: [1400, 14ff]
bus: 02 index 2 mmio: [50000000, 53ffffff]
bus: 02 index 3 mmio: [54000000, 57ffffff]
bus: 06 index 0 io port: [1800, 18ff]
bus: 06 index 1 io port: [1c00, 1cff]
bus: 06 index 2 mmio: [58000000, 5bffffff]
bus: 06 index 3 mmio: [5c000000, 5fffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
type=2000 audit(1225004854.313:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1764
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xf0000000, mapped to 0xf8880000, using 5742k, total
65536k
vesafb: mode is 1400x1050x16, linelength=2800, pages=21
vesafb: protected mode interface info at c000:53eb
vesafb: pmi: set display start = c00c547f, set palette = c00c54cb
vesafb: pmi: ports = d810 d816 d854 d838 d83c d85c d800 d804 d8b0 d8b2 d8b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 175x65
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 0000:00:02.6: PCI INT C -> GSI 18 (level, low) -> IRQ 18
serial 0000:00:02.6: PCI INT C disabled
brd: module loaded
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 364k freed
Switched to high resolution mode on CPU 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd 0000:00:03.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: cache line size of 128 is not supported
ehci_hcd 0000:00:03.3: irq 23, io mem 0xe5000000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-desktop-1mnb ehci_hcd
usb usb1: SerialNumber: 0000:00:03.3
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 20, io mem 0xe6800000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-desktop-1mnb ohci_hcd
usb usb2: SerialNumber: 0000:00:03.0
ohci_hcd 0000:00:03.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 21, io mem 0xe6000000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-2: new low speed USB device using ohci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: New USB device found, idVendor=0461, idProduct=4d03
usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-desktop-1mnb ohci_hcd
usb usb3: SerialNumber: 0000:00:03.1
ohci_hcd 0000:00:03.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 22, io mem 0xe5800000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-desktop-1mnb ohci_hcd
usb usb4: SerialNumber: 0000:00:03.2
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
No dock devices found.
libata version 3.00 loaded.
pata_sis 0000:00:02.5: version 0.5.2
scsi0 : pata_sis
scsi1 : pata_sis
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xb800 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xb808 irq 15
ata1.00: ATAPI: TOSHIBA DVD-ROM SD-R2312, 1708, max UDMA/33
ata1.00: configured for UDMA/33
ata2.00: ATA-6: ST980815A, 3.ALC, max UDMA/100
ata2.00: 156301488 sectors, multi 16: LBA48
ata2.00: configured for UDMA/100
scsi 0:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-R2312 1708 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access ATA ST980815A 3.AL PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 1:0:0:0: [sda] Attached SCSI disk
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all
legacy ISA IDE ports
ide_generic: I/O resource 0x1F0-0x1F7 not free.
ide_generic: I/O resource 0x170-0x177 not free.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: sda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 212327
EXT3-fs: sda1: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
TomoyoLinux Mandatory Access Control disabled by default.
You need to install ccs-tools if you want to enable it.
scsi 0:0:0:0: Attached scsi generic sg0 type 5
sd 1:0:0:0: Attached scsi generic sg1 type 0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Driver 'sr' needs updating - please use bus_type methods
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
asus-laptop: Asus Laptop Support version 0.42
asus-laptop: L5G model detected
input: Asus Extra Buttons as /class/input/input2
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
skge 0000:00:0d.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
skge 1.13 addr 0xe3800000 irq 18 chip Yukon rev 1
skge eth0: addr 00:0e:a6:cf:e0:cc
ACPI: Battery Slot [BAT0] (battery absent)
Marking TSC unstable due to TSC halts in idle
ACPI: AC Adapter [AC] (on-line)
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe800
ACPI: I/O resource 0000:00:02.1 [0xe800-0xe81f] conflicts with ACPI region SM00
[0xe800-0xe809]
ACPI: Device needs an ACPI driver
Linux agpgart interface v0.103
agpgart-sis 0000:00:00.0: SiS chipset [1039/0648]
IT8705 SuperIO detected.
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
agpgart-sis 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
ohci1394 0000:00:02.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[e7000000-e70007ff]
Max Packet=[2048] IR/IT contexts=[4/6]
ppdev: user-space parallel port driver
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (36 C)
fan PNP0C0B:00: registered as cooling_device1
ACPI: Fan [FAN0] (on)
Yenta: CardBus bridge found at 0000:00:0a.0 [1043:1734]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x01000222, devctl 0x44
usbcore: registered new interface driver hiddev
input: HID 0461:4d03 as /class/input/input7
input,hidraw0: USB HID v1.00 Mouse [HID 0461:4d03] on usb-0000:00:03.0-2
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Yenta: ISA IRQ mask 0x0c18, PCI irq 16
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:0a.1 [1043:1734]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.1, mfunc 0x01000222, devctl 0x44
Yenta: ISA IRQ mask 0x0828, PCI irq 17
Socket status: 30000006
Intel ICH Modem 0000:00:02.6: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Intel ICH 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800031a5cce]
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
intel8x0_measure_ac97_clock: measured 50876 usecs
intel8x0: clocking to 48000
b43-pci-bridge 0000:00:0c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ssb: Sonics Silicon Backplane found on PCI device 0000:00:0c.0
b43legacy-phy0: Broadcom 4301 WLAN found
b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2053, Revision 2
b43legacy-phy0 debug: Radio initialized
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx-legacy driver loaded [ Features: PLRID, Firmware-ID: FW10 ]
b44.c:v2.0
b44: Invalid MAC address found in EEPROM
b44 ssb0:1: Problem fetching invariants of chip, aborting.
b44: probe of ssb0:1 failed with error -22
[drm] Initialized drm 1.1.0 20060810
pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.29.0 20080528 on minor 0
Non-volatile memory driver v1.2
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
ide_generic: please use "probe_mask=0x3f" module parameter for probing all
legacy ISA IDE ports
ide_generic: I/O resource 0x1F0-0x1F7 not free.
ide_generic: I/O resource 0x170-0x177 not free.
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [EMAIL PROTECTED]
EXT3 FS on sda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: module loaded
Adding 4088500k swap on /dev/sda5. Priority:-1 extents:1 across:4088500k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip_tables: (C) 2000-2006 Netfilter Core Team
skge eth0: enabling interface
ADDRCONF(NETDEV_UP): eth0: link is not ready
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
input: b43legacy-phy0 as /class/input/input8
firmware: requesting b43legacy/ucode2.fw
firmware: requesting b43legacy/pcm4.fw
firmware: requesting b43legacy/b0g0initvals2.fw
b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18
02:36:27)
b43legacy-phy0 debug: Chip initialized
b43legacy-phy0 debug: 30-bit DMA initialized
b43legacy-phy0 debug: Wireless interface started
b43legacy-phy0 debug: Adding Interface type 2
ADDRCONF(NETDEV_UP): wlan0: link is not ready
skge eth0: Link is up at 100 Mbps, full duplex, flow control none
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ctnetlink v0.93: registering with nfnetlink.
ClusterIP Version 0.8 loaded successfully
wlan0: authenticate with AP a2:ae:a1:db:b3:c0
wlan0: authenticated
wlan0: associate with AP a2:ae:a1:db:b3:c0
wlan0: RX AssocResp from a2:ae:a1:db:b3:c0 (capab=0x11 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
NET: Registered protocol family 17
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
netfilter PSD loaded - (c) astaro AG
IFWLOG: register target
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
eth0: no IPv6 routers present
b43legacy-phy0: Radio hardware status changed to DISABLED
wlan0: no IPv6 routers present
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
agpgart-sis 0000:00:00.0: AGP 2.0 bridge
agpgart-sis 0000:00:00.0: putting AGP V3 device at 0000:00:00.0 into 16x mode
agpgart-sis 0000:00:00.0: SiS delay workaround: giving bridge time to recover
agpgart-sis 0000:00:00.0: putting AGP V3 device at 0000:01:00.0 into 16x mode
b43legacy-phy0: Radio hardware status changed to ENABLED
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
wlan0: authenticate with AP a2:ae:a1:db:b3:c3
wlan0: authenticated
wlan0: associate with AP a2:ae:a1:db:b3:c3
wlan0: mismatch in privacy configuration and mixed-cell disabled - abort
association
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0: Radio hardware status changed to DISABLED
b43legacy-phy0: Radio hardware status changed to ENABLED
b43legacy-phy0 debug: Removing Interface type 2
b43legacy-phy0 debug: Wireless interface stopped
b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 1/64
b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 3/64
b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots: 0/128
b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots: 0/128
b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots: 0/128
b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots: 0/128
b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots: 2/128
b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots: 0/128
b43legacy-phy0 debug: Radio initialized
b43legacy-phy0 debug: Radio initialized
APIC error on CPU0: 00(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
