Hi!
I recently made a fresh install of ubuntu hardy, upgraded weeks later to
intrepid. I have not had a working suspend for some time, but now this
works. Including b43.
However, after every other suspend (to ram) the status led indicates
that rf-kill switch is in wlan enabled state, although it is not. No
matter if I switch it on and off will it change the LED status. The
system log says that hw status changed, and indeed wlan0 will show AP's
in enabled state, but not in disabled state.
I compared the dmesg outputs (posted below), and the only thing that
differs is the last lines:
Working:
wlan0: authentication with AP 00:14:c1:1d:19:f0 timed out
b43-phy0: Radio hardware status changed to DISABLED
Non-working (order changed):
b43-phy0: Radio hardware status changed to DISABLED
wlan0: authentication with AP 00:14:c1:1d:19:f0 timed out
Also, when LED is working, I get these messages a few seconds after each
DISABLE, but not when LED is stuck:
[86215.196059] b43-phy0: Radio turned on by software
[86215.196078] b43-phy0: The hardware RF-kill button still turns the
radio physically off. Press the button to turn it on.
The LED used to work fine, but that was with an older ubuntu version,
and I believe it doesn't have to be a change in b43 that cause this
issue.
$ uname -a
Linux richie-laptop 2.6.27-7-generic #1 SMP Tue Nov 4 19:33:06 UTC 2008
x86_64 GNU/Linux
$ lspci -nnv -s 01:00.0
01:00.0 Network controller [0280]: Broadcom Corporation BCM4312
802.11a/b/g [14e4:4312] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:1361]
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at b3000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb, wl
Computer is a HP dv2140eu (dv2000) laptop.
Suspend-resume cycle after which LED is working:
$ dmesg
[86186.424108] PM: Syncing filesystems ... done.
[86186.424170] PM: Preparing system for mem sleep
[86186.424174] Freezing user space processes ... (elapsed 0.05 seconds)
done.
[86186.476709] Freezing remaining freezable tasks ... (elapsed 0.00
seconds) done.
[86186.476816] PM: Entering mem sleep
[86186.476819] Suspending console(s) (use no_console_suspend to debug)
[86186.477279] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[86186.801333] sd 2:0:0:0: [sda] Stopping disk
[86187.773538] ACPI handle has no context!
[86187.773547] sdhci-pci 0000:05:09.1: PCI INT B disabled
[86187.773552] ACPI handle has no context!
[86187.792067] ACPI handle has no context!
[86187.808090] b43-pci-bridge 0000:01:00.0: PCI INT A disabled
[86187.824284] forcedeth 0000:00:14.0: wake-up capability disabled by
ACPI
[86187.824288] forcedeth 0000:00:14.0: PME# disabled
[86187.856294] HDA Intel 0000:00:10.1: PCI INT B disabled
[86187.872145] sata_nv 0000:00:0e.0: PCI INT A disabled
[86187.904075] ehci_hcd 0000:00:0b.1: PCI INT B disabled
[86187.920066] ohci_hcd 0000:00:0b.0: PCI INT A disabled
[86187.936051] ohci_hcd 0000:00:0b.0: PME# enabled
[86187.936056] ohci_hcd 0000:00:0b.0: PME# enabled
[86187.936227] NVRM: RmPowerManagement: 4
[86189.254369] PM: suspend devices took 2.776 seconds
[86189.332103] ACPI: Preparing to enter system sleep state S3
[86189.452347] Disabling non-boot CPUs ...
[86189.452524] kvm: disabling virtualization on CPU1
[86189.454755] CPU 1 is now offline
[86189.454757] SMP alternatives: switching to UP code
[86189.470859] CPU0 attaching NULL sched-domain.
[86189.470863] CPU1 attaching NULL sched-domain.
[86189.484044] CPU0 attaching sched-domain:
[86189.484047] domain 0: span 0 level NODE
[86189.484050] groups: 0
[86189.484355] CPU1 is down
[86189.484491] Extended CMOS year: 2000
[86189.484491] Back to C!
[86189.484491] Extended CMOS year: 2000
[86189.488346] Enabling non-boot CPUs ...
[86189.488637] SMP alternatives: switching to SMP code
[86189.504900] Booting processor 1/1 ip 6000
[86189.456517] Initializing CPU#1
[86189.456517] Calibrating delay using timer specific routine.. 3214.72
BogoMIPS (lpj=6429457)
[86189.456517] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[86189.456517] CPU: L2 Cache: 512K (64 bytes/line)
[86189.456517] CPU 1/1 -> Node 0
[86189.456517] CPU: Physical Processor ID: 0
[86189.456517] CPU: Processor Core ID: 1
[86189.456517] Switch to broadcast mode on CPU1
[86189.592230] CPU1: AMD Turion(tm) 64 X2 stepping 02
[86189.592237] kvm: enabling virtualization on CPU1
[86189.592272] CPU0 attaching NULL sched-domain.
[86189.596039] Switched to high resolution mode on CPU 1
[86189.604050] CPU0 attaching sched-domain:
[86189.604054] domain 0: span 0-1 level MC
[86189.604056] groups: 0 1
[86189.604059] domain 1: span 0-1 level CPU
[86189.604061] groups: 0-1
[86189.604064] domain 2: span 0-1 level NODE
[86189.604066] groups: 0-1
[86189.604069] CPU1 attaching sched-domain:
[86189.604071] domain 0: span 0-1 level MC
[86189.604073] groups: 1 0
[86189.604076] domain 1: span 0-1 level CPU
[86189.604077] groups: 0-1
[86189.604080] domain 2: span 0-1 level NODE
[86189.604081] groups: 0-1
[86189.604721] CPU1 is up
[86189.604724] ACPI: Waking up from system sleep state S3
[86190.844709] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[86190.948437] pcieport-driver 0000:00:02.0: restoring config space at
offset 0xf (was 0x0, writing 0x400ff)
[86190.948443] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x9 (was 0x10011, writing 0x1fff1)
[86190.948447] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x8 (was 0x10, writing 0xb300b300)
[86190.948451] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x7 (was 0x101, writing 0x1f1)
[86190.948455] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x6 (was 0x0, writing 0x20100)
[86190.948459] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x3 (was 0x10000, writing 0x10010)
[86190.948463] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x1 (was 0x100000, writing 0x100407)
[86190.948480] pcieport-driver 0000:00:02.0: setting latency timer to 64
[86190.948493] pcieport-driver 0000:00:03.0: restoring config space at
offset 0xf (was 0x0, writing 0x400ff)
[86190.948498] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x9 (was 0x10011, writing 0xd011d001)
[86190.948502] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x8 (was 0x10, writing 0xb7f0b400)
[86190.948506] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x7 (was 0x101, writing 0x4141)
[86190.948509] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x6 (was 0x0, writing 0x40300)
[86190.948514] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x3 (was 0x10000, writing 0x10010)
[86190.948518] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x1 (was 0x100000, writing 0x100407)
[86190.948533] pcieport-driver 0000:00:03.0: setting latency timer to 64
[86190.948554] NVRM: RmPowerManagement: 5
[86191.496957] pci 0000:00:0a.3: restoring config space at offset 0xf
(was 0x1030200, writing 0x103020b)
[86191.497017] ohci_hcd 0000:00:0b.0: PME# disabled
[86191.497022] ohci_hcd 0000:00:0b.0: PME# disabled
[86191.512058] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[LUS0] -> GSI 23
(level, high) -> IRQ 23
[86191.512063] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[86191.552046] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[LUS2] -> GSI 22
(level, high) -> IRQ 22
[86191.552050] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[86191.568046] pata_amd 0000:00:0d.0: setting latency timer to 64
[86191.584055] sata_nv 0000:00:0e.0: restoring config space at offset
0x1 (was 0xb00005, writing 0xb00007)
[86191.584070] sata_nv 0000:00:0e.0: PCI INT A -> Link[LTID] -> GSI 18
(level, high) -> IRQ 18
[86191.584074] sata_nv 0000:00:0e.0: setting latency timer to 64
[86191.584305] pci 0000:00:10.0: setting latency timer to 64
[86191.600037] HDA Intel 0000:00:10.1: restoring config space at offset
0xf (was 0x5020200, writing 0x502020a)
[86191.600048] HDA Intel 0000:00:10.1: restoring config space at offset
0x4 (was 0x0, writing 0xb0000000)
[86191.600054] HDA Intel 0000:00:10.1: restoring config space at offset
0x1 (was 0xb00000, writing 0xb00002)
[86191.600068] HDA Intel 0000:00:10.1: PCI INT B -> Link[LAZA] -> GSI 22
(level, high) -> IRQ 22
[86191.600074] HDA Intel 0000:00:10.1: setting latency timer to 64
[86191.616050] forcedeth 0000:00:14.0: wake-up capability disabled by
ACPI
[86191.616054] forcedeth 0000:00:14.0: PME# disabled
[86191.632037] b43-pci-bridge 0000:01:00.0: enabling device (0000 ->
0002)
[86191.632043] b43-pci-bridge 0000:01:00.0: PCI INT A -> Link[LK2E] ->
GSI 19 (level, high) -> IRQ 19
[86191.632058] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0xf (was 0x100, writing 0x10a)
[86191.632073] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0x4 (was 0x0, writing 0xb3000000)
[86191.632077] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0x3 (was 0x0, writing 0x10)
[86191.632083] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0x1 (was 0x100002, writing 0x100007)
[86191.668047] ohci1394 0000:05:09.0: restoring config space at offset
0xf (was 0x4020100, writing 0x402010a)
[86191.668061] ohci1394 0000:05:09.0: restoring config space at offset
0x4 (was 0xc3100000, writing 0xb8000000)
[86191.668065] ohci1394 0000:05:09.0: restoring config space at offset
0x3 (was 0x800000, writing 0x804000)
[86191.668071] ohci1394 0000:05:09.0: restoring config space at offset
0x1 (was 0x2100000, writing 0x2100006)
[86191.719688] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[b8000000-b80007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[86191.737367] ata2.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
[86191.737370] ata2.00: ACPI cmd ef/03:08:00:00:00:a0 filtered out
[86191.737389] ata2: nv_mode_filter: 0x1&0x7001->0x1, BIOS=0x0 (0x0)
ACPI=0x7001 (60:600:0x11)
[86191.752338] ata2.00: configured for PIO0
[86191.752353] sdhci-pci 0000:05:09.1: restoring config space at offset
0xf (was 0x200, writing 0x20b)
[86191.752368] sdhci-pci 0000:05:09.1: restoring config space at offset
0x4 (was 0x0, writing 0xb8000800)
[86191.752372] sdhci-pci 0000:05:09.1: restoring config space at offset
0x3 (was 0x800000, writing 0x804000)
[86191.752378] sdhci-pci 0000:05:09.1: restoring config space at offset
0x1 (was 0x2100000, writing 0x2100006)
[86191.752391] sdhci-pci 0000:05:09.1: PCI INT B -> Link[LNK2] -> GSI 23
(level, high) -> IRQ 23
[86191.753399] pci 0000:05:09.2: restoring config space at offset 0xf
(was 0x200, writing 0x20b)
[86191.753414] pci 0000:05:09.2: restoring config space at offset 0x4
(was 0x0, writing 0xb8000c00)
[86191.753420] pci 0000:05:09.2: restoring config space at offset 0x1
(was 0x2100000, writing 0x2100002)
[86191.753434] pci 0000:05:09.3: restoring config space at offset 0xf
(was 0x200, writing 0x20b)
[86191.753449] pci 0000:05:09.3: restoring config space at offset 0x4
(was 0x0, writing 0xb8001000)
[86191.753455] pci 0000:05:09.3: restoring config space at offset 0x1
(was 0x2100000, writing 0x2100002)
[86191.918698] ata4: SATA link down (SStatus 0 SControl 300)
[86192.016044] usb 2-8: reset high speed USB device using ehci_hcd and
address 2
[86192.076079] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[86192.084240] ata3.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out
[86192.100405] ata3.00: configured for UDMA/100
[86192.100470] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors
(160042 MB)
[86192.100493] sd 2:0:0:0: [sda] Write Protect is off
[86192.100495] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[86192.100533] sd 2:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[86192.157332] uvcvideo 2-8:1.0: no reset_resume for driver uvcvideo?
[86192.157335] uvcvideo 2-8:1.1: no reset_resume for driver uvcvideo?
[86192.168102] sd 2:0:0:0: [sda] Starting disk
[86192.211482] uvcvideo: Found UVC 1.00 device USB 2.0 Camera
(0c45:62c0)
[86192.212934] input: USB 2.0 Camera
as /devices/pci0000:00/0000:00:0b.1/usb2/2-8/2-8:1.0/input/input21
[86192.224455] PM: resume devices took 1.700 seconds
[86192.224488] PM: Finishing wakeup.
[86192.224490] Restarting tasks ... done.
[86192.879844] eth0: no link during initialization.
[86192.880421] ADDRCONF(NETDEV_UP): eth0: link is not ready
[86194.576660] input: b43-phy0 as /devices/virtual/input/input22
[86194.781050] b43-phy0: Loading firmware version 351.126 (2006-07-29
05:54:02)
[86194.781061] b43-phy0 warning: You are using an old firmware image.
Support for old firmware will be removed in July 2008.
[86194.781067] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and
download the latest firmware (version 4).
[86194.920587] Registered led device: b43-phy0::tx
[86194.920618] Registered led device: b43-phy0::rx
[86194.920642] Registered led device: b43-phy0::radio
[86194.945153] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86194.945602] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[86194.956228] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86195.156058] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86195.356053] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86195.552042] wlan0: authentication with AP 00:14:c1:1d:19:f0 timed out
[86195.585048] b43-phy0: Radio hardware status changed to DISABLED
[86215.196059] b43-phy0: Radio turned on by software
[86215.196078] b43-phy0: The hardware RF-kill button still turns the
radio physically off. Press the button to turn it on.
After flicking switch on and off:
[86369.816069] b43-phy0: Radio hardware status changed to ENABLED
[86374.860057] b43-phy0: Radio hardware status changed to DISABLED
Suspend-resume cycle after which LED is stuck in ON mode:
[86820.319695] PM: Syncing filesystems ... done.
[86820.319766] PM: Preparing system for mem sleep
[86820.319770] Freezing user space processes ... (elapsed 0.00 seconds)
done.
[86820.321963] Freezing remaining freezable tasks ... (elapsed 0.00
seconds) done.
[86820.322082] PM: Entering mem sleep
[86820.322085] Suspending console(s) (use no_console_suspend to debug)
[86820.322541] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[86820.545229] sd 2:0:0:0: [sda] Stopping disk
[86821.517541] ACPI handle has no context!
[86821.517550] sdhci-pci 0000:05:09.1: PCI INT B disabled
[86821.517555] ACPI handle has no context!
[86821.536081] ACPI handle has no context!
[86821.552084] b43-pci-bridge 0000:01:00.0: PCI INT A disabled
[86821.568279] forcedeth 0000:00:14.0: wake-up capability disabled by
ACPI
[86821.568282] forcedeth 0000:00:14.0: PME# disabled
[86821.584051] HDA Intel 0000:00:10.1: PCI INT B disabled
[86821.600140] sata_nv 0000:00:0e.0: PCI INT A disabled
[86821.632074] ehci_hcd 0000:00:0b.1: PCI INT B disabled
[86821.648075] ohci_hcd 0000:00:0b.0: PCI INT A disabled
[86821.664036] ohci_hcd 0000:00:0b.0: PME# enabled
[86821.664041] ohci_hcd 0000:00:0b.0: PME# enabled
[86821.664212] NVRM: RmPowerManagement: 4
[86822.981893] PM: suspend devices took 2.660 seconds
[86823.060098] ACPI: Preparing to enter system sleep state S3
[86823.180351] Disabling non-boot CPUs ...
[86823.180530] kvm: disabling virtualization on CPU1
[86823.284026] CPU 1 is now offline
[86823.284029] SMP alternatives: switching to UP code
[86823.300083] CPU0 attaching NULL sched-domain.
[86823.300088] CPU1 attaching NULL sched-domain.
[86823.316050] CPU0 attaching sched-domain:
[86823.316053] domain 0: span 0 level NODE
[86823.316056] groups: 0
[86823.316374] CPU1 is down
[86823.316509] Extended CMOS year: 2000
[86823.316509] Back to C!
[86823.316509] Extended CMOS year: 2000
[86823.320367] Enabling non-boot CPUs ...
[86823.320657] SMP alternatives: switching to SMP code
[86823.336870] Booting processor 1/1 ip 6000
[86823.184523] Initializing CPU#1
[86823.184523] Calibrating delay using timer specific routine.. 3214.71
BogoMIPS (lpj=6429439)
[86823.184523] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[86823.184523] CPU: L2 Cache: 512K (64 bytes/line)
[86823.184523] CPU 1/1 -> Node 0
[86823.184523] CPU: Physical Processor ID: 0
[86823.184523] CPU: Processor Core ID: 1
[86823.184523] Switch to broadcast mode on CPU1
[86823.424208] CPU1: AMD Turion(tm) 64 X2 stepping 02
[86823.424215] kvm: enabling virtualization on CPU1
[86823.424250] CPU0 attaching NULL sched-domain.
[86823.428041] Switched to high resolution mode on CPU 1
[86823.436040] CPU0 attaching sched-domain:
[86823.436043] domain 0: span 0-1 level MC
[86823.436045] groups: 0 1
[86823.436049] domain 1: span 0-1 level CPU
[86823.436051] groups: 0-1
[86823.436053] domain 2: span 0-1 level NODE
[86823.436055] groups: 0-1
[86823.436059] CPU1 attaching sched-domain:
[86823.436060] domain 0: span 0-1 level MC
[86823.436062] groups: 1 0
[86823.436065] domain 1: span 0-1 level CPU
[86823.436066] groups: 0-1
[86823.436068] domain 2: span 0-1 level NODE
[86823.436071] groups: 0-1
[86823.436723] CPU1 is up
[86823.436725] ACPI: Waking up from system sleep state S3
[86824.676831] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[86824.780257] pcieport-driver 0000:00:02.0: restoring config space at
offset 0xf (was 0x0, writing 0x400ff)
[86824.780264] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x9 (was 0x10011, writing 0x1fff1)
[86824.780267] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x8 (was 0x10, writing 0xb300b300)
[86824.780271] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x7 (was 0x101, writing 0x1f1)
[86824.780275] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x6 (was 0x0, writing 0x20100)
[86824.780279] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x3 (was 0x10000, writing 0x10010)
[86824.780284] pcieport-driver 0000:00:02.0: restoring config space at
offset 0x1 (was 0x100000, writing 0x100407)
[86824.780300] pcieport-driver 0000:00:02.0: setting latency timer to 64
[86824.780313] pcieport-driver 0000:00:03.0: restoring config space at
offset 0xf (was 0x0, writing 0x400ff)
[86824.780318] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x9 (was 0x10011, writing 0xd011d001)
[86824.780322] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x8 (was 0x10, writing 0xb7f0b400)
[86824.780326] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x7 (was 0x101, writing 0x4141)
[86824.780330] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x6 (was 0x0, writing 0x40300)
[86824.780334] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x3 (was 0x10000, writing 0x10010)
[86824.780338] pcieport-driver 0000:00:03.0: restoring config space at
offset 0x1 (was 0x100000, writing 0x100407)
[86824.780353] pcieport-driver 0000:00:03.0: setting latency timer to 64
[86824.780374] NVRM: RmPowerManagement: 5
[86825.328719] pci 0000:00:0a.3: restoring config space at offset 0xf
(was 0x1030200, writing 0x103020b)
[86825.328771] ohci_hcd 0000:00:0b.0: PME# disabled
[86825.328776] ohci_hcd 0000:00:0b.0: PME# disabled
[86825.344054] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[LUS0] -> GSI 23
(level, high) -> IRQ 23
[86825.344059] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[86825.384044] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[LUS2] -> GSI 22
(level, high) -> IRQ 22
[86825.384048] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[86825.400051] pata_amd 0000:00:0d.0: setting latency timer to 64
[86825.416061] sata_nv 0000:00:0e.0: restoring config space at offset
0x1 (was 0xb00005, writing 0xb00007)
[86825.416076] sata_nv 0000:00:0e.0: PCI INT A -> Link[LTID] -> GSI 18
(level, high) -> IRQ 18
[86825.416080] sata_nv 0000:00:0e.0: setting latency timer to 64
[86825.416311] pci 0000:00:10.0: setting latency timer to 64
[86825.432047] HDA Intel 0000:00:10.1: restoring config space at offset
0xf (was 0x5020200, writing 0x502020a)
[86825.432059] HDA Intel 0000:00:10.1: restoring config space at offset
0x4 (was 0x0, writing 0xb0000000)
[86825.432064] HDA Intel 0000:00:10.1: restoring config space at offset
0x1 (was 0xb00000, writing 0xb00002)
[86825.432078] HDA Intel 0000:00:10.1: PCI INT B -> Link[LAZA] -> GSI 22
(level, high) -> IRQ 22
[86825.432083] HDA Intel 0000:00:10.1: setting latency timer to 64
[86825.448058] forcedeth 0000:00:14.0: wake-up capability disabled by
ACPI
[86825.448062] forcedeth 0000:00:14.0: PME# disabled
[86825.464042] b43-pci-bridge 0000:01:00.0: enabling device (0000 ->
0002)
[86825.464048] b43-pci-bridge 0000:01:00.0: PCI INT A -> Link[LK2E] ->
GSI 19 (level, high) -> IRQ 19
[86825.464063] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0xf (was 0x100, writing 0x10a)
[86825.464077] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0x4 (was 0x0, writing 0xb3000000)
[86825.464082] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0x3 (was 0x0, writing 0x10)
[86825.464088] b43-pci-bridge 0000:01:00.0: restoring config space at
offset 0x1 (was 0x100002, writing 0x100007)
[86825.500026] ohci1394 0000:05:09.0: restoring config space at offset
0xf (was 0x4020100, writing 0x402010a)
[86825.500040] ohci1394 0000:05:09.0: restoring config space at offset
0x4 (was 0xc3100000, writing 0xb8000000)
[86825.500045] ohci1394 0000:05:09.0: restoring config space at offset
0x3 (was 0x800000, writing 0x804000)
[86825.500051] ohci1394 0000:05:09.0: restoring config space at offset
0x1 (was 0x2100000, writing 0x2100006)
[86825.551668] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[b8000000-b80007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[86825.569352] ata2.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
[86825.569355] ata2.00: ACPI cmd ef/03:08:00:00:00:a0 filtered out
[86825.569374] ata2: nv_mode_filter: 0x1&0x7001->0x1, BIOS=0x0 (0x0)
ACPI=0x7001 (60:600:0x11)
[86825.584348] ata2.00: configured for PIO0
[86825.584362] sdhci-pci 0000:05:09.1: restoring config space at offset
0xf (was 0x200, writing 0x20b)
[86825.584377] sdhci-pci 0000:05:09.1: restoring config space at offset
0x4 (was 0x0, writing 0xb8000800)
[86825.584382] sdhci-pci 0000:05:09.1: restoring config space at offset
0x3 (was 0x800000, writing 0x804000)
[86825.584388] sdhci-pci 0000:05:09.1: restoring config space at offset
0x1 (was 0x2100000, writing 0x2100006)
[86825.584400] sdhci-pci 0000:05:09.1: PCI INT B -> Link[LNK2] -> GSI 23
(level, high) -> IRQ 23
[86825.585409] pci 0000:05:09.2: restoring config space at offset 0xf
(was 0x200, writing 0x20b)
[86825.585423] pci 0000:05:09.2: restoring config space at offset 0x4
(was 0x0, writing 0xb8000c00)
[86825.585430] pci 0000:05:09.2: restoring config space at offset 0x1
(was 0x2100000, writing 0x2100002)
[86825.585444] pci 0000:05:09.3: restoring config space at offset 0xf
(was 0x200, writing 0x20b)
[86825.585459] pci 0000:05:09.3: restoring config space at offset 0x4
(was 0x0, writing 0xb8001000)
[86825.585465] pci 0000:05:09.3: restoring config space at offset 0x1
(was 0x2100000, writing 0x2100002)
[86825.750684] ata4: SATA link down (SStatus 0 SControl 300)
[86825.848052] usb 2-8: reset high speed USB device using ehci_hcd and
address 2
[86825.908080] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[86825.916222] ata3.00: ACPI cmd ef/03:46:00:00:00:a0 filtered out
[86825.932402] ata3.00: configured for UDMA/100
[86825.932467] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors
(160042 MB)
[86825.932490] sd 2:0:0:0: [sda] Write Protect is off
[86825.932493] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[86825.932530] sd 2:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[86825.989332] uvcvideo 2-8:1.0: no reset_resume for driver uvcvideo?
[86825.989335] uvcvideo 2-8:1.1: no reset_resume for driver uvcvideo?
[86826.000131] sd 2:0:0:0: [sda] Starting disk
[86826.039476] uvcvideo: Found UVC 1.00 device USB 2.0 Camera
(0c45:62c0)
[86826.040935] input: USB 2.0 Camera
as /devices/pci0000:00/0000:00:0b.1/usb2/2-8/2-8:1.0/input/input23
[86826.052449] PM: resume devices took 1.696 seconds
[86826.052481] PM: Finishing wakeup.
[86826.052483] Restarting tasks ... done.
[86826.383938] eth0: no link during initialization.
[86826.384566] ADDRCONF(NETDEV_UP): eth0: link is not ready
[86826.397250] input: b43-phy0 as /devices/virtual/input/input24
[86828.024071] b43-phy0: Loading firmware version 351.126 (2006-07-29
05:54:02)
[86828.024082] b43-phy0 warning: You are using an old firmware image.
Support for old firmware will be removed in July 2008.
[86828.024087] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and
download the latest firmware (version 4).
[86828.164378] Registered led device: b43-phy0::tx
[86828.164438] Registered led device: b43-phy0::rx
[86828.164462] Registered led device: b43-phy0::radio
[86828.216338] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[86828.217508] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86828.416031] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86828.616039] wlan0: authenticate with AP 00:14:c1:1d:19:f0
[86828.800101] b43-phy0: Radio hardware status changed to DISABLED
[86828.816037] wlan0: authentication with AP 00:14:c1:1d:19:f0 timed out
Again, after flicking the switch on and off:
[87068.805050] b43-phy0: Radio hardware status changed to ENABLED
[87072.804082] b43-phy0: Radio hardware status changed to DISABLED
_______________________________________________
Bcm43xx-dev mailing list
Bcm43xx-dev@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
