I've got an HP pavilion ze4904us. This device has a Broadcom 4306 which worked
perfectly under Suse 10.3 with the bcm43xx module. Under Suse 11.1 with b43, it
loads the module starts the nic and works just fine for ten to twenty minutes.
After that, the signal strength appears to deteriorate, disurbing messages
begin to appear in dmesg, and finally the connection dies. Sometimes I can get
it to come back by reactivateing the connection through NetworkManager,
sometimes not.
I'm including uname, lspci, and dmesg, as suggested. Any help or advice is
appreciated. I can't be the only person to have had this problem, the 4306 is
not an uncommon device. Maybe it's already been fixed. Can someone point me at
the latest stable, or even not so stable, code?
sybill:~ # uname -a
Linux sybill 2.6.27.7-9-default #1 SMP 2008-12-04 18:10:04 +0100 i686 i686 i386
GNU/Linux
sybill:~ # lspci -vvn |grep 43 -A7
02:06.0 0280: 14e4:4320 (rev 03)
Subsystem: 103c:12f4
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
sybill:~ # dmesg
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20080609
ACPI: Checking initramfs for custom DSDT
Parsing all Control Methods:
Table [DSDT](id 0001) - 709 Objects with 58 Devices 210 Methods 16 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 1 Objects with 0 Devices 1 Methods 0 Regions
tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully acquired
ACPI: setting ELCR to 0200 (from 0c20)
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
weird, boot CPU (#0) not listedby the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (2597.78 BogoMIPS).
CPU0 attaching NULL sched-domain.
net_namespace: 1044 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9a2, last bus=2
PCI: Using configuration type 1 for base access
evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package
initialization:........................................................
Initialized 14/16 Regions 0/0 Fields 22/22 Buffers 20/20 Packages (719 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 0 _STA executions (examined 62 objects)
evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 5 Wake, Enabled 0 Runtime GPEs
in this block
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:02.0 reg 10 32bit mmio: [e8000000, efffffff]
PCI: 0000:00:02.0 reg 14 32bit mmio: [e0000000, e007ffff]
PCI: 0000:00:02.0 reg 18 io port: [1800, 1807]
pci 0000:00:02.0: supports D1
PCI: 0000:00:02.1 reg 10 32bit mmio: [f0000000, f7ffffff]
PCI: 0000:00:02.1 reg 14 32bit mmio: [e0080000, e00fffff]
pci 0000:00:02.1: supports D1
PCI: 0000:00:1d.0 reg 20 io port: [1820, 183f]
PCI: 0000:00:1d.1 reg 20 io port: [1840, 185f]
PCI: 0000:00:1d.2 reg 20 io port: [1860, 187f]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [e0100000, e01003ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
HPET not enabled in BIOS. You might try hpet=force boot option
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
PCI: 0000:00:1f.1 reg 20 io port: [1810, 181f]
PCI: 0000:00:1f.1 reg 24 32bit mmio: [0, 3ff]
PCI: 0000:00:1f.3 reg 20 io port: [1880, 189f]
PCI: 0000:00:1f.5 reg 10 io port: [1c00, 1cff]
PCI: 0000:00:1f.5 reg 14 io port: [18c0, 18ff]
PCI: 0000:00:1f.5 reg 18 32bit mmio: [e0100c00, e0100dff]
PCI: 0000:00:1f.5 reg 1c 32bit mmio: [e0100800, e01008ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
PCI: 0000:00:1f.6 reg 10 io port: [2400, 24ff]
PCI: 0000:00:1f.6 reg 14 io port: [2000, 207f]
pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.6: PME# disabled
PCI: 0000:02:00.0 reg 10 io port: [3000, 30ff]
PCI: 0000:02:00.0 reg 14 32bit mmio: [e0202000, e02020ff]
pci 0000:02:00.0: supports D1
pci 0000:02:00.0: supports D2
pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
PCI: 0000:02:05.0 reg 10 32bit mmio: [0, fff]
pci 0000:02:05.0: supports D1
pci 0000:02:05.0: supports D2
pci 0000:02:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:05.0: PME# disabled
PCI: 0000:02:06.0 reg 10 32bit mmio: [e0200000, e0201fff]
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 io port: [3000, 3fff]
PCI: bridge 0000:00:1e.0 32bit mmio: [e0200000, e02fffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
ACPI: PCI Interrupt Link [LNKC] (IRQs *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *11)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 7 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
AppArmor: AppArmor Filesystem Enabled
ACPI: RTC can wake from S4
system 00:04: ioport range 0x600-0x60f has been reserved
system 00:04: ioport range 0x800-0x80f has been reserved
system 00:04: ioport range 0x1000-0x107f has been reserved
system 00:04: ioport range 0x1180-0x11bf has been reserved
system 00:04: iomem range 0xfec10000-0xfec1ffff has been reserved
pci 0000:02:05.0: CardBus bridge, secondary bus 0000:03
pci 0000:02:05.0: IO window: 0x003400-0x0034ff
pci 0000:02:05.0: IO window: 0x003800-0x0038ff
pci 0000:02:05.0: PREFETCH window: 0x50000000-0x53ffffff
pci 0000:02:05.0: MEM window: 0x58000000-0x5bffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: 0x3000-0x3fff
pci 0000:00:1e.0: MEM window: 0xe0200000-0xe02fffff
pci 0000:00:1e.0: PREFETCH window: 0x00000050000000-0x00000053ffffff
pci 0000:00:1e.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
vendor=8086 device=2448
PCI: setting IRQ 11 as level-triggered
pci 0000:02:05.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 02 index 0 io port: [3000, 3fff]
bus: 02 index 1 mmio: [e0200000, e02fffff]
bus: 02 index 2 mmio: [50000000, 53ffffff]
bus: 02 index 3 io port: [0, ffff]
bus: 02 index 4 mmio: [0, ffffffff]
bus: 03 index 0 io port: [3400, 34ff]
bus: 03 index 1 io port: [3800, 38ff]
bus: 03 index 2 mmio: [50000000, 53ffffff]
bus: 03 index 3 mmio: [58000000, 5bffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 5713k freed
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
type=2000 audit(1235066728.772:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 440
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
vesafb: framebuffer at 0xe8000000, mapped to 0xf8880000, using 6144k, total
32576k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 100719 bytes
bootsplash: ...found (1024x768, 38691 bytes, v3).
Console: switching to colour frame buffer device 124x44
Switched to high resolution mode on CPU 0
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver8 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
serial 0000:00:1f.6: PCI INT B disabled
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PSM1] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 316k freed
Write protecting the kernel text: 2344k
Write protecting the kernel read-only data: 1768k
input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
ACPI: CPU0 (power states: C1[C1] C2[C2])
processor ACPI_CPU:00: registered as cooling_device0
Marking TSC unstable due to TSC halts in idle
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (24 C)
ACPI: No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
ata1: clearing spurious IRQ
ata1.00: ATA-8: TS32GSSD25-M, V0826, max UDMA/100
ata1.00: 62586880 sectors, multi 0: LBA
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1.00: configured for UDMA/100
ata2: clearing spurious IRQ
ata2.00: ATAPI: PHILIPS CD-RW/DVD-ROM CDD5263, UH89, max MWDMA2
ata2: clearing spurious IRQ
ata2: clearing spurious IRQ
ata2.00: configured for MWDMA2
scsi 0:0:0:0: Direct-Access ATA TS32GSSD25-M V082 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM PHILIPS CDRW/DVD CDD5263 UH89 PQ: 0 ANSI: 5
Uniform Multi-Platform E-IDE driver
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
udevd version 128 started
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input1
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not
after
sd 0:0:0:0: [sda] 62586880 512-byte hardware sectors: (32.0GB/29.8GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 62586880 512-byte hardware sectors: (32.0GB/29.8GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-9-default uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.7-9-default uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27.7-9-default uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xe0100000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27.7-9-default ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
PM: Starting manual resume from disk
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 128 started
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 855GM Chipset
agpgart-intel 0000:00:00.0: detected 32636K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID0]
input: Power Button (CM) as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
ACPI: Power Button (CM) [PWRB]
ACPI: AC Adapter [ACAD] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: WMI: Mapper loaded
acpi device:05: registered as cooling_device1
input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:02/input/input5
ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
intel_rng: FWH not detected
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:02:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:02:00.0: Try the "8139too" driver instead.
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
Yenta: CardBus bridge found at 0000:02:05.0 [103c:3084]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:05.0, mfunc 0x01111112, devctl 0x64
8139too Fast Ethernet driver 0.9.28
sr0: scsi3-mmc drive: 1x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
Yenta: ISA IRQ mask 0x00d8, PCI irq 11
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe02fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
input: PC Speaker as /devices/platform/pcspkr/input/input6
vendor=8086 device=2448
b43-pci-bridge 0000:02:06.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) ->
IRQ 11
ssb: Sonics Silicon Backplane found on PCI device 0000:02:06.0
i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
Intel ICH 0000:00:1f.5: setting latency timer to 64
intel8x0_measure_ac97_clock: measured 53964 usecs
intel8x0: clocking to 48000
vendor=8086 device=2448
8139too 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xf90de000, 00:c0:9f:51:32:d1, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) ->
IRQ 5
Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
ALSA sound/pci/ac97/ac97_codec.c:2154: MC'97 0 converters and GPIO not ready
(0x1)
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
b43-phy0: Broadcom 4306 WLAN found
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
Adding 1502004k swap on /dev/sda5. Priority:-1 extents:1 across:1502004k
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected]
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
type=1505 audit(1235084738.541:2): operation="profile_load" name="/bin/ping"
name2="default" pid=1609
type=1505 audit(1235084738.677:3): operation="profile_load" name="/sbin/klogd"
name2="default" pid=1632
type=1505 audit(1235084738.925:4): operation="profile_load"
name="/sbin/syslog-ng" name2="default" pid=1646
type=1505 audit(1235084739.165:5): operation="profile_load"
name="/sbin/syslogd" name2="default" pid=1684
type=1505 audit(1235084739.401:6): operation="profile_load"
name="/usr/sbin/avahi-daemon" name2="default" pid=1699
type=1505 audit(1235084739.593:7): operation="profile_load"
name="/usr/sbin/identd" name2="default" pid=1714
type=1505 audit(1235084739.781:8): operation="profile_load"
name="/usr/sbin/mdnsd" name2="default" pid=1731
type=1505 audit(1235084740.033:9): operation="profile_load"
name="/usr/sbin/nscd" name2="default" pid=1745
type=1505 audit(1235084740.293:10): operation="profile_load"
name="/usr/sbin/ntpd" name2="default" pid=1762
type=1505 audit(1235084740.433:11): operation="profile_load"
name="/usr/sbin/traceroute" name2="default" pid=1766
powernow: This module only works with AMD K7 CPUs
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IA-32 Microcode Update Driver: v1.14a <[email protected]>
firmware: requesting intel-ucode/06-09-05
microcode: CPU0 updated from revision 0x45 to 0x47, date = 11092004
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
pci 0000:00:02.1: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 1
[drm:i915_getparam] *ERROR* Unknown parameter 5
[drm:i915_getparam] *ERROR* Unknown parameter 5
bootsplash: status on console 0 changed to on
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
input: b43-phy0 as /devices/virtual/input/input7
firmware: requesting b43/ucode5.fw
firmware: requesting b43/pcm5.fw
firmware: requesting b43/b0g0initvals5.fw
firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
ADDRCONF(NETDEV_UP): wlan0: link is not ready
NET: Registered protocol family 17
wlan0: authenticate with AP 00:1c:10:c6:85:4b
wlan0: authenticated
wlan0: associate with AP 00:1c:10:c6:85:4b
wlan0: RX AssocResp from 00:1c:10:c6:85:4b (capab=0x401 status=0 aid=2)
wlan0: associated
wlan0: disassociating by local choice (reason=3)
wlan0: No ProbeResp from current AP 00:1c:10:c6:85:4b - assume out of range
[drm:i915_getparam] *ERROR* Unknown parameter 5
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
wlan0: authenticate with AP 00:30:44:02:76:d2
wlan0: authenticated
wlan0: associate with AP 00:30:44:02:76:d2
wlan0: RX AssocResp from 00:30:44:02:76:d2 (capab=0x431 status=0 aid=5)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
martian source 255.255.255.255 from 192.168.0.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:30:44:02:76:d2:08:00
martian source 255.255.255.255 from 192.168.0.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:30:44:02:76:d2:08:00
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=248 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=228
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=472 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=452
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=472 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=452
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=472 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=452
wlan0: no IPv6 routers present
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=wlan0 OUT= MAC= SRC=192.168.0.189 DST=224.0.0.251
LEN=64 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
b43-phy0 ERROR: PHY transmission error
wlan0: No ProbeResp from current AP 00:30:44:02:76:d2 - assume out of range
wlan0: authenticate with AP 00:30:44:02:76:d2
wlan0: authenticate with AP 00:30:44:02:76:d2
wlan0: authenticate with AP 00:30:44:02:76:d2
wlan0: authenticate with AP 00:30:44:02:76:d2
wlan0: authentication with AP 00:30:44:02:76:d2 timed out
mtcs...@sybill:~/Desktop>
Many thanks
John Mountcastle
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
