Hello Group,
I posted a few days ago my problems with this WLAN minipci card:
Linux OpenWrt 2.6.28.10 #5 Thu Sep 10 20:36:33 CEST 2009 armv5teb unknown
00:02.0 0280: 14e4:4325 (rev 02)
Subsystem: 1414:0004
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 48020000 (32-bit, non-prefetchable) [disabled]
[size=8K]
If I use them (2 pieces) in a WP188 from compex, I don't get ssb.ko running.
Here is the dmesg if I try to load ssb.ko and b43legacy.ko
PCI: enabling device 0000:00:02.0 (0140 -> 0142)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x02, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x01, vendor 0x4243)
ssb: Core 3 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x07, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
ssb: Ignoring additional 802.11 core
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
ssb: SPROM revision 251 detected.
ssb: Unsupported SPROM revision 251 detected. Will extract v1
ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
PCI: enabling device 0000:00:04.0 (0140 -> 0142)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x02, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x01, vendor 0x4243)
ssb: Core 3 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x07, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x04, vendor 0x4243)
ssb: Ignoring additional 802.11 core
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
ssb: SPROM revision 251 detected.
ssb: Unsupported SPROM revision 251 detected. Will extract v1
ssb: Sonics Silicon Backplane found on PCI device 0000:00:04.0
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
b43legacy-phy0: Broadcom 4306 WLAN found
phy0: Failed to initialize wep: -2
b43legacy: probe of ssb0:0 failed with error -2
b43legacy-phy1: Broadcom 4306 WLAN found
phy1: Failed to initialize wep: -2
b43legacy: probe of ssb1:0 failed with error -2
Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
One time I managed it to run for half an hour.
I think it is a PCI problem of IPX4XX?
Because running the same cards in my ALIX works without problems!
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
b43-pci-bridge 0000:00:0c.0: setting latency timer to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:00:0c.0
b43-pci-bridge 0000:00:0e.0: setting latency timer to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:00:0e.0
b43legacy-phy0: Broadcom 4306 WLAN found
phy0: Selected rate control algorithm 'minstrel'
b43legacy-phy1: Broadcom 4306 WLAN found
phy1: Selected rate control algorithm 'minstrel'
Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
Registered led device: alix:1
Registered led device: alix:2
Registered led device: alix:3
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
via-rhine 0000:00:09.0: setting latency timer to 64
eth0: VIA Rhine III (Management Adapter) at 0xe0000000, 00:0d:b9:12:83:b8, IRQ
10.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
eth0: link down
device eth0 entered promiscuous mode
b43legacy ssb0:0: firmware: requesting b43legacy/ucode4.fw
b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18
02:36:27)
Registered led device: b43legacy-phy0::tx
Registered led device: b43legacy-phy0::rx
Registered led device: b43legacy-phy0::radio
b43legacy ssb1:0: firmware: requesting b43legacy/ucode4.fw
b43legacy ssb1:0: firmware: requesting b43legacy/pcm4.fw
b43legacy ssb1:0: firmware: requesting b43legacy/b0g0initvals2.fw
b43legacy-phy1: Loading firmware version 0x127, patch level 14 (2005-04-18
02:36:27)
Registered led device: b43legacy-phy1::tx
Registered led device: b43legacy-phy1::rx
Registered led device: b43legacy-phy1::radio
Even the SPROM is readable on the SSB:
r...@openwrt:/# cat /sys/devices/pci0000:00/0000:00:0c.0/ssb_sprom
014000000400141425430080020002000010001800000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF0D00713A0DF9
FFFFFFFFFFFFFFFFFFFFFFFFFFFF2130B01198FB4FFE88030B0B3C000000000000003E000F00FF
FF0000000000000000014D
r...@openwrt:/#
Does anybody know what I can change in OpenWRT relating to PCI options for
WP188?
Thanks for any help,
Daniel
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
