Am Mittwoch, den 16.09.2009, 21:40 +0200 schrieb Gábor Stefanik:
> You are essentially implementing dead code at this point - this will
> only ever be called if hardware-accelerated TX power control is
> enabled - and HW TX power control is unsupported, even for G-PHYs.
Then the question remains, why this brings my device to 54 MBit/s ?
I did double check again with the old driver:
wlan0 IEEE 802.11bg ESSID:"tommy"
Mode:Managed Frequency:2.412 GHz Access Point:
Bit Rate=9 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=5 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Patched driver:
wlan0 IEEE 802.11bg ESSID:"tommy"
Mode:Managed Frequency:2.412 GHz Access Point: XXX
Bit Rate=54 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=10 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
> > Signed-off-by: Thomas Ilnseher <[email protected]>
> >
> > ---
> > diff -uNr a/drivers/net/wireless/b43/phy_lp.c
> > b/drivers/net/wireless/b43/phy_lp.c
> > --- a/drivers/net/wireless/b43/phy_lp.c 2009-09-16 20:52:17.501318374 +0200
> > +++ b/drivers/net/wireless/b43/phy_lp.c 2009-09-16 20:53:36.593319452 +0200
> > @@ -1125,6 +1125,18 @@
> > dev->phy.lp->tssi_idx = (b43_phy_read(dev,
> > B43_LPPHY_TX_PWR_CTL_STAT) & 0x7F00) >> 8;
> > }
> >
> > +static void lpphy_clear_tx_power_offsets(struct b43_wldev *dev)
> > +{
> > + int i;
> > + int id = 7;
> > + if (dev->phy.rev < 2)
> > + id = 10;
> > + for (i = 0; i < 12; i++)
> > + b43_lptab_write(dev, B43_LPTAB32(id, 0x40 + i), 0);
> > + for (i = 0; i < 64; i++)
> > + b43_lptab_write(dev, B43_LPTAB32(id, 0x80 + i), 0);
> > +}
> > +
> > static void lpphy_set_tx_power_control(struct b43_wldev *dev,
> > enum b43_lpphy_txpctl_mode mode)
> > {
> > @@ -1139,7 +1151,7 @@
> >
> > if (oldmode == B43_LPPHY_TXPCTL_HW) {
> > lpphy_update_tx_power_npt(dev);
> > - //TODO Clear all TX Power offsets
> > + lpphy_clear_tx_power_offsets(dev);
> > } else {
> > if (mode == B43_LPPHY_TXPCTL_HW) {
> > //TODO Recalculate target TX power
> >
> >
>
>
>
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
