Hi, I received my new BBB few days ago and I'm eager to start playing with it. I'm having problem trying to use the microSD as extra storage. I Flashed the eMMc with the latest img: BBB-eMMC-flasher-2013.06.20.img
It worked fine. I followed then the instructions here: http://circuitco.com/support/index.php?title=MicroSD_As_Extra_Storage I partitioned the microSD card in the following partitions: - a 32MB FAT32 partition to host the uEnv.txt file - the rest as etx4 partition for storage. http://screencast.com/t/gZGJdvfhE (I actually made many tests with various filesystem types) I wrote the following text in uEnv.txt mmcdev=1 bootpart=1:2 mmcroot=/dev/mmcblk1p2 ro optargs=quiet But then whe I put the microSD in the BBB and see what the serial console shows me I see that it stops saying: ** Bad partition specification mmc 1:2 ** mmc 1:2 refers to the value of bootpart in uEnv.txt I tried with bootpart=1:1 and I get then ** Bad partition specification mmc 1:1 ** (I even tried after upgrading all packages with opkg update/upgrade) So, what am I missing now? The strange things is that few days ago I followed exactly the same procedure and it worked without any issue: the BBB boot withe microSSD in and later I could mount the both partitions. But now it looks like something is changed. Any suggestion? Thanks in advance PS. below you find the serial console output when I boot the BBB with the microSD in ----------- U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 64 bytes read in 3 ms (20.5 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... gpio: pin 55 (gpio 55) value is 1 mmc_send_cmd : timeout: No status update ** Bad partition specification mmc 1:2 ** U-Boot# -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/groups/opt_out.