unplug everything from the board while you're flashing it. e.g. dont leave your ethernet cable plugged in during.
On Mon, Sep 30, 2013 at 6:53 AM, Gerald Coley <[email protected]>wrote: > Five minutes is not necessary. Only about 10 seconds is required. Sounds > like the SD card was not created properly or the SD card is bad or needs > reformatting. Try reformatting it as indicated on the instructions or try > a different SD card. > > Gerald > . > > > On Mon, Sep 30, 2013 at 8:50 AM, Steven Feldman < > [email protected]> wrote: > >> Following those instructions, I re-flashed my SD Card, inserted the card >> and ensured everything was disconnected from the BBB. Then I held the boot >> switch button in as I plugged in the DC power connector. I continued to >> hold it in for 5 minutes, however the first (or any) of the user LED lights >> did not come on. The only light on is the one indicating the board has >> power. >> >> >> On Mon, Sep 30, 2013 at 8:31 AM, Gerald Coley <[email protected]>wrote: >> >>> As I said, recreate the flasher SD card. Try it again. >>> >>> Follow the instructions on the support Wiki. >>> >>> Here is the direct link >>> http://circuitco.com/support/index.php?title=Updating_The_Software >>> >>> Gerald >>> >>> >>> On Sun, Sep 29, 2013 at 9:56 PM, Steven Feldman < >>> [email protected]> wrote: >>> >>>> The first time I did it, I was plugged into DC outlet, and my house >>>> briefly lost power...About an hour ago, I tried again, however none of the >>>> 4 activity led lights are on. Only the power led. >>>> >>>> >>>> On Sun, Sep 29, 2013 at 9:50 PM, Gerald Coley >>>> <[email protected]>wrote: >>>> >>>>> Recreate the flashing SD card. Try it again. >>>>> >>>>> As the instructions say, do not have Ethernet plugged in when doing >>>>> the flashing. And as the instructions say, do not attempt it using USB >>>>> power. >>>>> >>>>> Gerald >>>>> >>>>> >>>>> >>>>> On Sun, Sep 29, 2013 at 8:04 PM, Steven Feldman < >>>>> [email protected]> wrote: >>>>> >>>>>> I lost power while attempting to flash my emmc, and now when I power >>>>>> up my board only the power light comes on, and if the ethernet cable is >>>>>> plugged in then those lights are on. >>>>>> >>>>>> No combinations of pressing user boot, reset, power, power source can >>>>>> get the activity lights to come on. >>>>>> >>>>>> Any ideas? >>>>>> >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to [email protected]. >>>>>> >>>>>> For more options, visit https://groups.google.com/groups/opt_out. >>>>>> >>>>> >>>>> -- >>>>> For more options, visit http://beagleboard.org/discuss >>>>> --- >>>>> You received this message because you are subscribed to a topic in the >>>>> Google Groups "BeagleBoard" group. >>>>> To unsubscribe from this topic, visit >>>>> https://groups.google.com/d/topic/beagleboard/ArdvjdBvVII/unsubscribe. >>>>> To unsubscribe from this group and all its topics, send an email to >>>>> [email protected]. >>>>> >>>>> For more options, visit https://groups.google.com/groups/opt_out. >>>>> >>>> >>>> >>>> >>>> -- >>>> Steven Douglas Feldman >>>> University of Central Florida >>>> Computer Software Engineering >>>> Scalable and Secure Systems Lab >>>> Orlando Fl, >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/groups/opt_out. >>>> >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to a topic in the >>> Google Groups "BeagleBoard" group. >>> To unsubscribe from this topic, visit >>> https://groups.google.com/d/topic/beagleboard/ArdvjdBvVII/unsubscribe. >>> To unsubscribe from this group and all its topics, send an email to >>> [email protected]. >>> For more options, visit https://groups.google.com/groups/opt_out. >>> >> >> >> >> -- >> Steven Douglas Feldman >> University of Central Florida >> Computer Software Engineering >> Scalable and Secure Systems Lab >> Orlando Fl, >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/groups/opt_out. >> > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/groups/opt_out. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
