Can't input angthing after booting... Hi,r I have a clone beagleboard, and tried to install linux on it. But, whatever I was installed, Angstrom, Ubuntu or a linux built by myselft, I can't input angthing by minicom or other terminal software.I can't stop autoboot, can't input the bootcmd, can't type user and password.
But I can see the output of the board! There is no dvi interface on the board, and network didn't go well.Although it have a TFT LCD, but in general system didn't support it. I put some boot infomation in the attachment.The attachment infomation based on ubuntu release https://rcn-ee.net/deb/rootfs/raring/ubuntu-13.04-console-armhf-2013-09-26.tar.xz . Thanks. -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
40W�H��ս��сSPL 2013.07-00016-gbc15ff8 (Aug 16 2013 - 10:41:31) OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.07-00016-gbc15ff8 (Aug 16 2013 - 10:41:31) OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0 * Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Beagle Rev Ax/Bx i2c_probe: pads on bus 1 probably not configured (status=0x10) No EEPROM on expansion board i2c_probe: pads on bus 1 probably not configured (status=0x10) No EEPROM on expansion board Die ID #46da000400000000040398e50900e007 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 1.400 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 480ab000 using PIO, IRQ 0 Net: usb_ether Hit any key to stop autoboot: 0 mmc0 is current device gpio: pin 173 (gpio 173) value is 1 gpio: pin 7 (gpio 7) value is 0 SD/MMC found on device 0 reading uEnv.txt 1559 bytes read in 4 ms (379.9 KiB/s) Importing environment from mmc ... Checking if uenvcmd is set ... Running uenvcmd ... reading zImage 3422232 bytes read in 256 ms (12.7 MiB/s) reading initrd.img 3345891 bytes read in 250 ms (12.8 MiB/s) Kernel image @ 0x80300000 [ 0x000000 - 0x343818 ] Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.7.10-x13 (root@imx6q-sabrelite-1gb-0)(gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-1ubuntu1) ) #1 SMP Wed Jun 26 13:08:55 UT3 [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board [ 0.000000] Beagle expansionboard: none [ 0.000000] Beagle expansionboard2: none [ 0.000000] Beagle wl12xx clk: none [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM [ 0.000000] cma: CMA: reserved 16 MiB at 8d800000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp ) [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0cc0000 s13312 r8192 d15360 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 59904 [ 0.000000] Kernel command line: console=ttyO2,115200n8 console=tty0 vram=12M omapfb.mode=dvi:1280x720MR-16@60 omapdss.def_disp=dvi root=/dev/mmcble [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 236MB = 236MB total [ 0.000000] Memory: 208172k/208172k available, 53972k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc090a020 (9225 kB) [ 0.000000] .init : 0xc090b000 - 0xc096b400 ( 385 kB) [ 0.000000] .data : 0xc096c000 - 0xc09f30f0 ( 541 kB) [ 0.000000] .bss : 0xc09f3114 - 0xc0abbc98 ( 803 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000976] Calibrating delay loop... 402.29 BogoMIPS (lpj=1572864) [ 0.055267] pid_max: default: 32768 minimum: 301 [ 0.055480] Security Framework initialized [ 0.055541] AppArmor: AppArmor initialized [ 0.055847] Mount-cache hash table entries: 512 [ 0.057037] Initializing cgroup subsys cpuacct [ 0.057067] Initializing cgroup subsys memory [ 0.057159] Initializing cgroup subsys devices [ 0.057159] Initializing cgroup subsys freezer [ 0.057189] Initializing cgroup subsys blkio [ 0.057220] Initializing cgroup subsys perf_event [ 0.057373] CPU: Testing write buffer coherency: ok [ 0.057708] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.057830] Setting up static identity map for 0x8065d040 - 0x8065d098 [ 0.059326] Brought up 1 CPUs [ 0.059387] SMP: Total of 1 processors activated (402.29 BogoMIPS). [ 0.060546] devtmpfs: initialized [ 0.115692] pinctrl core: initialized pinctrl subsystem [ 0.116363] regulator-dummy: no parameters [ 0.118011] NET: Registered protocol family 16 [ 0.123352] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.123901] omap-gpmc omap-gpmc: GPMC revision 5.0 [ 0.126617] OMAP GPIO hardware version 2.5 [ 0.131988] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.133361] OMAP3 Beagle Rev: Ax/Bx [ 0.144348] Reprogramming SDRC clock to 332000000 Hz [ 0.146026] Found NAND on CS0 [ 0.146057] Registering NAND on CS0 [ 0.146575] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.146881] Could not look up dss_hdmi hw_mod [ 0.147094] Could not look up dmic hw_mod [ 0.147125] Could not look up mcpdm hw_mod [ 0.150604] omap-mcbsp.2: alias fck already exists [ 0.151031] omap-mcbsp.3: alias fck already exists [ 0.152221] OMAP DMA hardware revision 4.0 [ 0.154144] arm-pmu: alias fck already exists [ 0.166229] bio: create slab <bio-0> at 0 [ 0.184417] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.185516] SCSI subsystem initialized [ 0.186370] usbcore: registered new interface driver usbfs [ 0.186492] usbcore: registered new interface driver hub [ 0.186706] usbcore: registered new device driver usb [ 0.187194] musb-omap2430 musb-omap2430: invalid resource [ 0.199920] twl 1-0048: PIH (irq 23) chaining IRQs 338..346 [ 0.200134] twl 1-0048: power (irq 343) chaining IRQs 346..353 [ 0.201354] twl4030_gpio twl4030_gpio: gpio (irq 338) chaining IRQs 354..371 [ 0.203552] VUSB1V5: 1500 mV normal standby [ 0.204132] VUSB1V8: 1800 mV normal standby [ 0.204711] VUSB3V1: 3100 mV normal standby [ 0.206970] twl4030_usb twl4030_usb: Initialized TWL4030 USB module [ 0.207824] vdd_mpu_iva: 600 <--> 1450 mV normal [ 0.208374] vdd_core: 600 <--> 1450 mV normal [ 0.209075] VMMC1: 1850 <--> 3150 mV at 3150 mV normal standby [ 0.209777] VDAC: 1800 mV normal standby [ 0.210510] VDVI: 1800 mV normal standby [ 0.211334] VSIM: 1800 <--> 3000 mV at 1800 mV normal standby [ 0.212432] VAUX3: 1800 mV normal standby [ 0.213531] VAUX4: 1800 mV normal standby [ 0.213958] omap_i2c omap_i2c.1: bus 1 rev1.3.12 at 2600 kHz [ 0.214050] omap_i2c omap_i2c.1: bus 1 rev1.3.12 at 2600 kHz [ 0.214691] omap_i2c omap_i2c.2: bus 2 rev1.3.12 at 400 kHz [ 0.214843] omap_i2c omap_i2c.2: bus 2 rev1.3.12 at 400 kHz [ 0.231231] omap_i2c omap_i2c.3: bus 3 rev1.3.12 at 100 kHz [ 0.231323] omap_i2c omap_i2c.3: bus 3 rev1.3.12 at 100 kHz [ 0.231536] media: Linux media interface: v0.10 [ 0.231658] Linux video capture interface: v2.00 [ 0.232330] omap-iommu omap-iommu.0: isp registered [ 0.232696] Advanced Linux Sound Architecture Driver Initialized. [ 0.233520] NetLabel: Initializing [ 0.233551] NetLabel: domain hash size = 128 [ 0.233581] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.233673] NetLabel: unlabeled traffic allowed by default [ 0.234222] Switching to clocksource 32k_counter [ 0.263153] AppArmor: AppArmor Filesystem Enabled [ 0.279357] NET: Registered protocol family 2 [ 0.280426] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.280639] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.280853] TCP: Hash tables configured (established 8192 bind 8192) [ 0.280975] TCP: reno registered [ 0.281005] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.281066] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.281738] NET: Registered protocol family 1 [ 0.282287] RPC: Registered named UNIX socket transport module. [ 0.282318] RPC: Registered udp transport module. [ 0.282348] RPC: Registered tcp transport module. [ 0.282379] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.282714] usbhs_omap usbhs_omap: xclk60mhsp2_ck set parentfailed error:-22 [ 0.283813] Trying to unpack rootfs image as initramfs... [ 0.679718] Freeing initrd memory: 3264K [ 0.680633] CPU PMU: probing PMU on CPU 0 [ 0.680694] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.681732] omap_dsp_init: 600000 bytes @ 8ee00000 [ 0.684234] audit: initializing netlink socket (disabled) [ 0.684356] type=2000 audit(0.671:1): initialized [ 0.942596] VFS: Disk quotas dquot_6.5.2 [ 0.943145] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.947662] NFS: Registering the id_resolver key type [ 0.947784] Key type id_resolver registered [ 0.947814] Key type id_legacy registered [ 0.947875] fuse init (API version 7.20) [ 0.950408] Btrfs loaded [ 0.950469] msgmni has been set to 444 [ 0.953033] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.953094] io scheduler noop registered [ 0.953094] io scheduler deadline registered [ 0.953186] io scheduler cfq registered (default) [ 0.955139] OMAP DSS rev 2.0 [ 0.958709] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.960754] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0 [ 0.961700] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1 [ 0.962432] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 90) is a OMAP UART2 [ 1.853240] console [ttyO2] enabled [ 1.869232] brd: module loaded [ 1.878845] loop: module loaded [ 1.883972] twl4030_madc twl4030_madc: clk disabled, enabling [ 1.893371] No NAND device found [ 1.897033] No NAND device found [ 1.900848] OneNAND driver initializing [ 1.908111] usbcore: registered new interface driver cdc_ether [ 1.914520] usbcore: registered new interface driver rndis_host [ 1.920867] usbcore: registered new interface driver cdc_ncm [ 1.927917] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.935180] ehci-omap.0 supply hsusb1 not found, using dummy regulator [ 1.942413] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 1.948822] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 2.992706] ehci-omap ehci-omap.0: irq 93, io mem 0x48064800 [ 3.008361] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 3.014556] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.021881] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.029632] usb usb1: Product: OMAP-EHCI Host Controller [ 3.035400] usb usb1: Manufacturer: Linux 3.7.10-x13 ehci_hcd [ 3.041595] usb usb1: SerialNumber: ehci-omap.0 [ 3.047424] hub 1-0:1.0: USB hub found [ 3.051452] hub 1-0:1.0: 3 ports detected [ 3.056274] Initializing USB Mass Storage driver... [ 3.061584] usbcore: registered new interface driver usb-storage [ 3.068084] USB Mass Storage support registered. [ 3.073089] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 4.078948] twl4030_usb twl4030_usb: Timeout setting T2 HSUSB PHY DPLL clock [ 4.089233] musb-hdrc musb-hdrc.0: USB OTG mode controller at fa0ab000 using DMA, IRQ 108 [ 4.098327] gadget: using random self ethernet address [ 4.104003] gadget: using random host ethernet address [ 4.110351] usb0: MAC de:47:36:fe:70:91 [ 4.114410] usb0: HOST MAC 42:ff:33:a1:d8:17 [ 4.119110] gadget: Ethernet Gadget, version: Memorial Day 2008 [ 4.125579] gadget: g_ether ready [ 4.129211] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 4.135345] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 [ 4.143371] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.150695] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.158447] usb usb2: Product: MUSB HDRC host driver [ 4.163696] usb usb2: Manufacturer: Linux 3.7.10-x13 musb-hcd [ 4.169891] usb usb2: SerialNumber: musb-hdrc.0 [ 4.175537] hub 2-0:1.0: USB hub found [ 4.179534] hub 2-0:1.0: 1 port detected [ 4.184753] mousedev: PS/2 mouse device common for all mice [ 4.192199] input: twl4030_pwrbutton as /devices/platform/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0 [ 4.204589] twl_rtc twl_rtc: Enabling TWL-RTC [ 4.211608] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 4.219696] i2c /dev entries driver [ 4.224365] lirc_dev: IR Remote Control driver registered, major 246 [ 4.231445] smssdio: Siano SMS1xxx SDIO driver [ 4.236297] smssdio: Copyright Pierre Ossman [ 4.240875] Driver for 1-wire Dallas network protocol. [ 4.247406] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 4.255218] twl4030_wdt twl4030_wdt: Failed to register misc device [ 4.261962] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 4.269653] device-mapper: ioctl: 4.23.0-ioctl (2012-07-25) initialised: [email protected] [ 4.279144] cpuidle: using governor ladder [ 4.283630] cpuidle: using governor menu [ 4.287841] sdhci: Secure Digital Host Controller Interface driver [ 4.294494] sdhci: Copyright(c) Pierre Ossman [ 4.300476] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk [ 4.306976] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 4.314056] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 4.700195] ledtrig-cpu: registered to indicate activity on CPUs [ 4.709411] usbcore: registered new interface driver usbhid [ 4.715454] usbhid: USB HID core driver [ 4.720428] ashmem: initialized [ 4.813812] omap-twl4030 omap-twl4030: twl4030-hifi <-> omap-mcbsp.2 mapping ok [ 4.824249] oprofile: using arm/armv7 [ 4.828918] TCP: cubic registered [ 4.833312] NET: Registered protocol family 10 [ 4.839538] NET: Registered protocol family 17 [ 4.844848] Key type dns_resolver registered [ 4.849853] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 4.863922] ThumbEE CPU extension supported. [ 4.868652] Registering SWP/SWPB emulation handler [ 4.873718] SmartReflex Class3 initialized [ 4.887420] clock: disabling unused clocks to save power [ 4.894683] registered taskstats version 1 [ 4.899444] fbcvt: 1280x720@60: CVT Name - .921M9-R [ 4.920196] Console: switching to colour frame buffer device 160x45 [ 4.942321] VAUX4: incomplete constraints, leaving on [ 4.948730] VAUX3: incomplete constraints, leaving on [ 4.954467] VDAC: incomplete constraints, leaving on [ 4.961761] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:11:36 UTC (946685496) [ 4.970703] sr_init: No PMIC hook to init smartreflex [ 4.976348] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 4.985137] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 4.993896] cpufreq_cpu0: failed to find cpu0 node [ 4.999511] ALSA device list: [ 5.002929] #0: omap3beagle [ 5.011108] Freeing init memory: 384K [ 5.070281] mmc0: new high speed SDHC card at address 0001 [ 5.086608] mmcblk0: mmc0:0001 00000 7.46 GiB [ 5.103851] mmcblk0: p1 p2 [ 5.186218] udevd[76]: starting version 175 [ 6.844604] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 6.856353] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 8.633209] EXT4-fs (mmcblk0p2): recovery complete [ 8.652770] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 9.517089] init: ureadahead main process (194) terminated with status 5 [ 10.801269] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro Ubuntu 13.04 arm ttyO2 arm login:
