Hi and thanks for your reply. I compiled the kernel and think everything went well - though the compiling was the first time for me. Running Debian Wheezy and just replaced old kernel files and modules, result: no errors, so maybe the kernel configuration is ok?
uname -a Linux arm 3.13.0-rc6-bone2.8 #1 SMP Thu Jan 2 18:36:05 EET 2014 armv7l GNU/Linux Boot dmesg: [ 9.651818] em28xx: New device @ 480 Mbps (eb1a:2861, interface 0, class 0) [ 9.659456] em28xx: Video interface 0 found: isoc [ 9.666582] em28xx: chip ID is em2860 [ 9.820225] em2860 #0: board has no eeprom [ 9.939942] em2860 #0: No sensor detected [ 10.026297] em2860 #0: found i2c device @ 0x4a on bus 0 [saa7113h] [ 10.135650] em2860 #0: Your board has no unique USB ID. [ 10.141274] em2860 #0: A hint were successfully done, based on i2c devicelist hash. [ 10.149328] em2860 #0: This method is not 100% failproof. [ 10.154989] em2860 #0: If the board were missdetected, please email this log to: [ 10.162759] em2860 #0: V4L Mailing List <[email protected]> [ 10.169710] em2860 #0: Board detected as EM2860/SAA711X Reference Design [ 10.299533] em2860 #0: Identified as EM2860/SAA711X Reference Design (card=19) [ 10.969864] saa7115 1-0025: saa7113 found @ 0x4a (em2860 #0) [ 12.259479] em2860 #0: Config register raw data: 0x10 [ 12.299378] em2860 #0: AC97 vendor ID = 0x56494161 [ 12.319343] em2860 #0: AC97 features = 0x6d50 [ 12.323913] em2860 #0: Unknown AC97 audio processor detected! [ 13.109356] em2860 #0: v4l2 driver version 0.2.0 [ 16.310172] em2860 #0: V4L2 video device registered as video0 [ 16.316216] em2860 #0: V4L2 VBI device registered as vbi0 [ 16.321946] em2860 #0: analog set to isoc mode. [ 16.326806] em28xx audio device (eb1a:2861): interface 1, class 1 [ 16.333276] em28xx audio device (eb1a:2861): interface 2, class 1 [ 16.339765] usbcore: registered new interface driver em28xx [ 16.406268] usbcore: registered new interface driver snd-usb-audio [ 16.436762] em2860 #0: Registering snapshot button... [ 16.442479] input: em28xx snapshot button as /devices/ocp.3/47400000.usb/ 47401c00.usb/musb-hdrc.1.auto/usb2/2-1/input/input0 [ 16.455544] em2860 #0: Remote control support is not available for this card. motion: [0] Processing thread 0 - config file /etc/motion/motion.conf [0] Motion 3.2.12 Started [0] ffmpeg LIBAVCODEC_BUILD 3482368 LIBAVFORMAT_BUILD 3478785 [0] Thread 1 is from /etc/motion/motion.conf [1] Thread 1 started [1] cap.driver: "em28xx" [1] cap.card: "EM2860/SAA711X Reference Design" [1] cap.bus_info: "usb-musb-hdrc.1.auto-1" [1] cap.capabilities=0x85020011 [1] - VIDEO_CAPTURE [1] - VBI_CAPTURE [1] - AUDIO [1] - READWRITE [1] - STREAMING [1] Config palette index 8 (YU12) doesn't work. [1] Supported palettes: [1] 0: YUYV (16 bpp YUY2, 4:2:2, packed) [1] 1: RGBP (16 bpp RGB 565, LE) [1] 2: BA81 (8 bpp Bayer BGBG..GRGR) [1] 3: GRBG (8 bpp Bayer GRGR..BGBG) [1] 4: GBRG (8 bpp Bayer GBGB..RGRG) [1] 5: 411P (12 bpp YUV411) [1] Selected palette YUYV [1] Test palette YUYV (320x240) [1] Using palette YUYV (320x240) bytesperlines 640 sizeimage 153600 colorspace 00000001 [1] found control 0x00980900, "Brightness", range 0,255 [1] "Brightness", default 128, current 128 [1] found control 0x00980901, "Contrast", range 0,127 [1] "Contrast", default 64, current 64 [1] found control 0x00980902, "Saturation", range 0,127 [1] "Saturation", default 64, current 64 [1] found control 0x00980903, "Hue", range -128,127 [1] "Hue", default 0, current 0 [1] found control 0x0098090e, "Red Balance", range -48,48 [1] "Red Balance", default 0, current 0 [1] found control 0x0098090f, "Blue Balance", range -48,48 [1] "Blue Balance", default 0, current 0 [1] mmap information: [1] frames=4 [1] 0 length=153600 [1] 1 length=153600 [1] 2 length=153600 [1] 3 length=153600 [1] Using V4L2 [1] Resizing pre_capture buffer to 1 items [0] Thread 1 - Watchdog timeout, trying to do a graceful restart [0] Thread 1 - Watchdog timeout, did NOT restart graceful,killing it! [0] Calling vid_close() from motion_cleanup [0] Closing video device /dev/video0 [0] Motion thread 1 restart [1] Thread 1 started [1] cap.driver: "em28xx" [1] cap.card: "EM2860/SAA711X Reference Design" [1] cap.bus_info: "usb-musb-hdrc.1.auto-1" [1] cap.capabilities=0x85020011 ... So result is: not working. The dongle's green led is on as before, but no capture. Good news is that the dongle was recognized without reboot! -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
