Mine too Sri. Did you fix this issue or findout whats wrong. On Saturday, November 2, 2013 8:56:44 PM UTC+5:30, [email protected] wrote: > > Hello, > > According to U-boot, there are serious issues on my new A6 BBB: > > U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) > timed out in wait_for_pin: I2C_STAT=0 > Could not probe the EEPROM; something fundamentally wrong on the I2C bus. > Could not get board ID. > Unknown board, assuming Beaglebone LT/Black.musb-hdrc: ConfigData=0xde > (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) > musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Peripheral mode controller at 47401000 using PIO, IRQ 0 > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) > musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Host mode controller at 47401800 using PIO, IRQ 0 > OMAP SD/MMC: 0 > mmc_send_cmd : timeout: No status update > reading u-boot.img > reading u-boot.img > > > U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) > > I2C: ready > DRAM: 512 MiB > WARNING: Caches not enabled > timed out in wait_for_pin: I2C_STAT=0 > Could not probe the EEPROM; something fundamentally wrong on the I2C bus. > Could not get board ID. > NAND: No NAND device found!!! > 0 MiB > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > *** Warning - readenv() failed, using default environment > > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) > musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Peripheral mode controller at 47401000 using PIO, IRQ 0 > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) > musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Host mode controller at 47401800 using PIO, IRQ 0 > Net: <ethaddr> not set. Validating first E-fuse MAC > cpsw, usb_ether > Hit any key to stop autoboot: 0 > U-Boot# > > The error "Could not probe the EEPROM" and "No NAND device found" show up. >
-- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
