Beaglebone Black REV B
4DSystem LCD7
boot Angstrom on emmc -> /etc/dogtag=Cloud9 GNOME Image 2013.09.04
power DC 5v , > 2A
*after power on I can see the beaglebone logo on LCD and then bbb reboot
?!*
bbb without LCD7 is OK
bbb with HDMI is OK
tried :
- BBB-ubuntu-13.10-2013-12-17-4gb.img.xz on SDCARD
same as Angstrom
- bone-debian-7.4-2014-03-27-2gb.img.xz on SDCARD
same as Angstrom but after linux logo I see a few text lines asking for
user login just before board reboot
- test with and without keyboard and mouse connected
- test with and without ethernet connected
Anyone got same problem ?
bbb or lcd7 fault ?
what kind of test I can do ? (got only one bbb and one lcd7 ...)
thanks for help
start message (bbb+lcd7+Angstrom emmc) :
---------------------------------------------------------------------------------------
U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc_send_cmd : timeout: No status update
Card did not respond to voltage select!
mmc0(part 0) is current device
Card did not respond to voltage select!
No micro SD card found, setting mmcdev to 1
mmc1(part 0) is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 1
reading uEnv.txt
26 bytes read in 3 ms (7.8 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
gpio: pin 55 (gpio 55) value is 1
4385024 bytes read in 765 ms (5.5 MiB/s)
gpio: pin 56 (gpio 56) value is 1
24808 bytes read in 53 ms (457 KiB/s)
Booting from mmc ...
## Booting kernel from Legacy Image at 80007fc0 ...
Image Name: Angstrom/3.8.13/beaglebone
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4384960 Bytes = 4.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 80f80000
Booting using the fdt blob at 0x80f80000
XIP Kernel Image ... OK
OK
Using Device Tree in place at 80f80000, end 80f890e7
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.196292] omap2_mbox_probe: platform not supported
[ 0.206862] tps65217-bl tps65217-bl: no platform data provided
[ 0.306879] bone-capemgr bone_capemgr.8: slot #1: No cape found
[ 0.343983] bone-capemgr bone_capemgr.8: slot #2: No cape found
[ 0.381092] bone-capemgr bone_capemgr.8: slot #3: No cape found
[ 0.406416] bone-capemgr bone_capemgr.8: slot #5: BB-BONELT-HDMI
conflict P8.45 (#0:BB-BONE-LCD7-01)
[ 0.416031] bone-capemgr bone_capemgr.8: slot #5: Failed verification
[ 0.425576] bone-capemgr bone_capemgr.8: slot #6: BB-BONELT-HDMIN
conflict P8.45 (#0:BB-BONE-LCD7-01)
[ 0.435278] bone-capemgr bone_capemgr.8: slot #6: Failed verification
[ 0.455141] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset'
failed
[ 0.462471] bone-capemgr bone_capemgr.8: loader: failed to load slot-6
BB-BONELT-HDMIN:00A0 (prio 2)
[ 0.472078] bone-capemgr bone_capemgr.8: loader: failed to load slot-5
BB-BONELT-HDMI:00A0 (prio 1)
[ 0.539752] pinctrl-single 44e10800.pinmux: pin 44e10854 already
requested by 44e10800.pinmux; cannot claim for gpio-leds.7
[ 0.551498] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status
-22
[ 0.558808] pinctrl-single 44e10800.pinmux: could not request pin 21 on
device pinctrl-single
[ 0.724826] tilcdc 4830e000.fb: timeout waiting for framedone
---------------------------------------------------------------------------------------
reboot and repeat same sequence
---------------------------------------------------------------------------------------
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
