I had similar errors and in my case it was due to the power adapter. Try one with a higher output, or if you already have one that has high output get one that is better quality.
I had the problem when using a cheap generic adapter rated at 2.0A output. Switching to a higher quality adapter (Asus brand... included with a Nexus 7) rated at the same 2.0A output solved it. Kirk On Monday, May 5, 2014 9:33:04 AM UTC-7, Ross Morrison wrote: > > Hello everyone, > > I'm getting these error messages (see bottom of dmesg) on a custom BBB > clone running Robert Nelson's 3.14 kernel (Linux debian-BBB 3.14.2-bone2 > #1 SMP). Just wondering if this USB Ethernet dongle + this kernel and > drivers are a know problem, or do I need to look at my setup first? The > 4th line indicates something isn't correct, but continues on installing > the device. The kernel does panic after minimal network activity. > > Thanks for any ideas, > > Ross > > [ 3.008883] Freeing unused kernel memory: 452K (c0a03000 - c0a74000) > [ 3.082742] udevd[90]: starting version 175 > [ 3.334944] usb 2-1: new high-speed USB device number 2 using musb-hdrc > [ 3.487948] usb 2-1: device v0b95 p7720 is not supported > [ 3.493536] usb 2-1: New USB device found, idVendor=0b95, > idProduct=7720 > [ 3.493548] usb 2-1: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 3.493559] usb 2-1: Product: AX88x72A > [ 3.493568] usb 2-1: Manufacturer: ASIX Elec. Corp. > [ 3.493577] usb 2-1: SerialNumber: 000341 > [ 5.080783] EXT4-fs (mmcblk0p5): INFO: recovery required on readonly > filesystem > [ 5.080805] EXT4-fs (mmcblk0p5): write access will be enabled during > recovery > [ 5.587829] EXT4-fs (mmcblk0p5): recovery complete > [ 5.593775] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data > mode. Opts: (null) > [ 6.880852] udevd[294]: starting version 175 > [ 7.753219] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc > as rtc0 > [ 7.980917] random: nonblocking pool is initialized > [ 7.982936] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 > [ 8.028227] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 > [ 10.026273] asix 2-1:1.0 eth0: register 'asix' at > usb-musb-hdrc.1.auto-1, ASIX AX88772 USB 2.0 Ethernet, 8c:ae:4c:fe:08:fc > [ 10.026460] usbcore: registered new interface driver asix > [ 12.012171] Adding 999420k swap on /dev/mmcblk0p6. Priority:-1 > extents:1 across:999420k SS > [ 12.100942] EXT4-fs (mmcblk0p5): re-mounted. Opts: (null) > [ 12.355552] EXT4-fs (mmcblk0p5): re-mounted. Opts: errors=remount-ro > [ 12.652495] loop: module loaded > [ 15.810401] FAT-fs (mmcblk0p1): Volume was not properly unmounted. > Some data may be corrupt. Please run fsck. > [ 18.221203] Installing knfsd (copyright (C) 1996 > [email protected]<javascript:>). > > [ 22.836948] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready > [ 22.844798] asix 2-1:1.0 eth2: link down > [ 22.913774] net eth1: initializing cpsw version 1.12 (0) > [ 22.915445] libphy: PHY 4a101000.mdio:00 not found > [ 22.920470] net eth1: phy 4a101000.mdio:00 not found on slave 0 > [ 22.926697] libphy: PHY 4a101000.mdio:01 not found > [ 22.931713] net eth1: phy 4a101000.mdio:01 not found on slave 1 > [ 22.944677] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready > [ 24.757386] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready > [ 24.758900] asix 2-1:1.0 eth2: link up, 100Mbps, full-duplex, lpa > 0xCDE1 > [ 28.569708] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xc06b20ea, offset 4 > [ 48.635405] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length 0x0, > offset 4 > [ 174.610560] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0x32313030, offset 4 > [ 177.553399] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length 0x0, > offset 1100 > [ 177.918173] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xff4ca462, offset 1098 > [ 332.059440] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0x3726, offset 1068 > [ 616.028472] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xfaffffef, offset 1098 > [ 618.605235] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0x48435241, offset 1100 > [ 618.649417] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0x32313030, offset 4 > [ 622.038136] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xffffffff, offset 1098 > [ 1060.059988] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xfaffffef, offset 1098 > [ 1063.061273] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xfaffffef, offset 1098 > [ 1065.439877] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length 0x0, > offset 1100 > [ 1066.063387] asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length > 0xfaffffef, offset 1098 > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
