I also do not like it AM3517_CRANE # nand info Device 0: NAND 256MiB 3,3V 16-bit, sector size 128 KiB AM3517_CRANE # nand erase 0x80000 0x200000 NAND erase: device 0 offset 0x80000, size 0x200000 Erasing at 0x260000 -- 100% complete. OK
четверг, 3 июля 2014 г., 15:42:31 UTC+4 пользователь lisarden написал: > > Creating 5 MTD partitions on "omap2-nand.0": > 0x000000000000-0x000000080000 : "xloader-nand" > uncorrectable error : > 0x000000080000-0x000000240000 : "uboot-nand" > uncorrectable error : > 0x000000240000-0x000000280000 : "params-nand" > uncorrectable error : > 0x000000280000-0x000000780000 : "linux-nand" > uncorrectable error : > 0x000000780000-0x000010000000 : "jffs2-nand" > > I don't like "uncorrectable error". What about the pin mux settings? Check > u-boot sources if they are correct > What u-boot says about NAND? > nand info > nand erase > > > 2014-07-03 15:38 GMT+04:00 Андрей Кононов <[email protected] <javascript:>> > : > >> >> / # dmesg >> Linux version 2.6.32 (kon@kononov) (gcc version 4.3.3 (Sourcery G++ Lite >> 2009q1-203) ) #1 Thu Jul 3 15:13:51 MSK 2014 >> CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c53c7f >> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache >> Machine: AM3517/05 CRANEBOARD >> Memory policy: ECC disabled, Data cache writeback >> On node 0 totalpages: 65536 >> free_area_init_node: node 0, pgdat c03c3b94, node_mem_map c03e1000 >> Normal zone: 512 pages used for memmap >> Normal zone: 0 pages reserved >> Normal zone: 65024 pages, LIFO batch:15 >> AM3517 ES3.1 (l2cache iva sgx neon isp ) >> SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 >> Reserving 4194304 bytes SDRAM for VRAM >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 >> Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw >> rootfstype=ext3 rootwait eth=80:02:8e:c4:0d: ip=dhcp >> PID hash table entries: 1024 (order: 0, 4096 bytes) >> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) >> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) >> Memory: 256MB = 256MB total >> Memory: 251648KB available (3396K code, 304K data, 140K init, 0K highmem) >> Hierarchical RCU implementation. >> NR_IRQS:368 >> Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >> GPMC revision 5.0 >> IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts >> Total of 96 interrupts on 1 active controller >> OMAP GPIO hardware version 2.5 >> OMAP clockevent source: GPTIMER1 at 32768 Hz >> Console: colour dummy device 80x30 >> Calibrating delay loop... 493.67 BogoMIPS (lpj=1929216) >> Mount-cache hash table entries: 512 >> CPU: Testing write buffer coherency: ok >> regulator: core version 0.5 >> NET: Registered protocol family 16 >> mux: Could not set signal i2c2_scl >> mux: Could not set signal i2c2_sda >> mux: Could not set signal i2c3_scl >> mux: Could not set signal i2c3_sda >> Configuring SPI balls >> Registering SPI driver >> mux: Setting signal gpmc_a2.gpio35 0x0014 -> 0x0004 >> mux: Setting signal gpmc_a5.gpio38 0x001c -> 0x0004 >> mux: Setting signal gpmc_ncs1.gpio52 0x001c -> 0x0004 >> mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0118 -> 0x0118 >> mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat4.sdmmc1_dat4 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat5.sdmmc1_dat5 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat6.sdmmc1_dat6 0x0110 -> 0x0118 >> mux: Setting signal sdmmc1_dat7.sdmmc1_dat7 0x0110 -> 0x0118 >> OMAP DMA hardware revision 4.0 >> bio: create slab <bio-0> at 0 >> SCSI subsystem initialized >> omap2_mcspi omap2_mcspi.1: registered master spi1 >> spi spi1.0: setup: speed 48000000, sample trailing edge, clk normal >> spi spi1.0: setup mode 1, 8 bits/w, 48000000 Hz max --> 0 >> omap2_mcspi omap2_mcspi.1: registered child spi1.0 >> omap2_mcspi omap2_mcspi.2: registered master spi2 >> omap2_mcspi omap2_mcspi.3: registered master spi3 >> omap2_mcspi omap2_mcspi.4: registered master spi4 >> spi spi4.0: setup: speed 48000000, sample trailing edge, clk normal >> spi spi4.0: setup mode 1, 8 bits/w, 48000000 Hz max --> 0 >> omap2_mcspi omap2_mcspi.4: registered child spi4.0 >> i2c_omap i2c_omap.1: bus 1 rev3.12 at 400 kHz >> i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz >> i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz >> Switching to clocksource 32k_counter >> NET: Registered protocol family 2 >> IP route cache hash table entries: 2048 (order: 1, 8192 bytes) >> TCP established hash table entries: 8192 (order: 4, 65536 bytes) >> TCP bind hash table entries: 8192 (order: 3, 32768 bytes) >> TCP: Hash tables configured (established 8192 bind 8192) >> TCP reno registered >> UDP hash table entries: 256 (order: 0, 4096 bytes) >> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) >> NET: Registered protocol family 1 >> RPC: Registered udp transport module. >> RPC: Registered tcp transport module. >> RPC: Registered tcp NFSv4.1 backchannel transport module. >> NetWinder Floating Point Emulator V0.97 (double precision) >> VFS: Disk quotas dquot_6.5.2 >> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. >> msgmni has been set to 491 >> alg: No test for stdrng (krng) >> io scheduler noop registered >> io scheduler deadline registered >> io scheduler cfq registered (default) >> OMAP DSS rev 2.0 >> OMAP DISPC rev 3.0 >> OMAP VENC rev 2 >> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 >> serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 >> serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 >> console [ttyS2] enabled >> brd: module loaded >> loop: module loaded >> omap2-nand driver initializing >> NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB >> 3,3V 16-bit) >> Creating 5 MTD partitions on "omap2-nand.0": >> 0x000000000000-0x000000080000 : "xloader-nand" >> uncorrectable error : >> 0x000000080000-0x000000240000 : "uboot-nand" >> uncorrectable error : >> 0x000000240000-0x000000280000 : "params-nand" >> uncorrectable error : >> 0x000000280000-0x000000780000 : "linux-nand" >> uncorrectable error : >> 0x000000780000-0x000010000000 : "jffs2-nand" >> ftl_cs: FTL header not found. >> vcan: Virtual CAN interface driver >> CAN device driver interface >> TI High End CAN Controller Driver 0.7 >> ti_hecc ti_hecc.1: device registered (reg_base=d0860000, irq=24) >> tps65910_rtc tps65910_rtc: rtc core: registered tps65910_rtc as rtc0 >> TPS65910 RTC device successfully registered >> Linux video capture interface: v2.00 >> OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >> TCP cubic registered >> NET: Registered protocol family 17 >> NET: Registered protocol family 15 >> can: controller area network core (rev 20090105 abi 8) >> NET: Registered protocol family 29 >> can: raw protocol (rev 20090105) >> can: broadcast manager protocol (rev 20090105 t) >> Power Management for TI OMAP3. >> Disabling unused clock "hsotgusb_fck" >> Disabling unused clock "hsotgusb_ick" >> Disabling unused clock "vpfe_fck" >> Disabling unused clock "vpfe_ick" >> Disabling unused clock "emac_fck" >> Disabling unused clock "emac_ick" >> Disabling unused clock "mcbsp_fck" >> Disabling unused clock "mcbsp_fck" >> Disabling unused clock "mcbsp_fck" >> Disabling unused clock "mcbsp_ick" >> Disabling unused clock "mcbsp_ick" >> Disabling unused clock "mcbsp_ick" >> Disabling unused clock "gpt2_ick" >> Disabling unused clock "gpt3_ick" >> Disabling unused clock "gpt4_ick" >> Disabling unused clock "gpt5_ick" >> Disabling unused clock "gpt6_ick" >> Disabling unused clock "gpt7_ick" >> Disabling unused clock "gpt8_ick" >> Disabling unused clock "gpt9_ick" >> Disabling unused clock "wdt3_ick" >> Disabling unused clock "wdt3_fck" >> Disabling unused clock "gpio2_dbck" >> Disabling unused clock "gpio3_dbck" >> Disabling unused clock "gpio4_dbck" >> Disabling unused clock "gpio5_dbck" >> Disabling unused clock "gpio6_dbck" >> Disabling unused clock "gpt9_fck" >> Disabling unused clock "gpt8_fck" >> Disabling unused clock "gpt7_fck" >> Disabling unused clock "gpt6_fck" >> Disabling unused clock "gpt5_fck" >> Disabling unused clock "gpt4_fck" >> Disabling unused clock "gpt3_fck" >> Disabling unused clock "gpt2_fck" >> Disabling unused clock "gpt12_ick" >> Disabling unused clock "wdt1_ick" >> Disabling unused clock "gpio1_dbck" >> Disabling unused clock "mcbsp_ick" >> Disabling unused clock "mcbsp_ick" >> Disabling unused clock "gpt10_ick" >> Disabling unused clock "gpt11_ick" >> Disabling unused clock "hdq_ick" >> Disabling unused clock "hdq_fck" >> Disabling unused clock "mcbsp_fck" >> Disabling unused clock "mcbsp_fck" >> Disabling unused clock "gpt11_fck" >> Disabling unused clock "gpt10_fck" >> Disabling unused clock "dpll4_m6x2_ck" >> Disabling unused clock "dpll4_m5x2_ck" >> Disabling unused clock "dpll3_m3x2_ck" >> Disabling unused clock "sys_clkout1" >> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 >> emac-mii: probed >> tps65910_rtc tps65910_rtc: setting system clock to 2011-04-05 01:56:25 >> UTC (1301968585) >> mmc0: new high speed SDHC card at address 1234 >> mmcblk0: mmc0:1234 SA04G 3.63 GiB >> mmcblk0: p1 p2 >> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, >> id=7c0f1) >> IP-Config: Guessing netmask 255.0.0.0 >> IP-Config: Complete: >> device=eth0, addr=62.0.0.0, mask=255.0.0.0, gw=255.255.255.255, >> host=62.0.0.0, domain=, nis-domain=(none), >> bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= >> kjournald starting. Commit interval 5 seconds >> EXT3-fs (mmcblk0p2): using internal journal >> EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode >> VFS: Mounted root (ext3 filesystem) on device 179:2. >> Freeing init memory: 140K >> PHY: ffffffff:00 - Link is Up - 100/Full >> >> четверг, 3 июля 2014 г., 15:29:00 UTC+4 пользователь lisarden написал: >>> >>> dmesg >>> >>> >>> 2014-07-03 15:26 GMT+04:00 Андрей Кононов <[email protected]>: >>> >>> I have these settings, except one (CONFIG_MTD_NAND_ECC=y). I add it to >>>> defchonfig but the situation has not changed :(. >>>> >>>> четверг, 3 июля 2014 г., 14:50:58 UTC+4 пользователь lisarden написал: >>>>> >>>>> CONFIG_MTD=y >>>>> CONFIG_MTD_CHAR=y >>>>> CONFIG_MTD_BLKDEVS=y >>>>> CONFIG_MTD_BLOCK=y >>>>> CONFIG_MTD_NAND_ECC=y >>>>> CONFIG_MTD_NAND=y >>>>> CONFIG_MTD_NAND_OMAP2=y >>>>> CONFIG_MTD_NAND_IDS=y >>>>> >>>>> >>>>> >>>>> 2014-07-03 14:46 GMT+04:00 Андрей Кононов <[email protected]>: >>>>> >>>>>> what can i include in the kernel to organize writing mtd partitions? >>>>>> kernel 2.6.32 >>>>>> >>>>>>> / # flash_eraseall /dev/mtd3 >>>>>>> flash_eraseall: can't open '/dev/mtd3': No such device or address >>>>>>> / # ls /dev/mtd* >>>>>>> /dev/mtd0 /dev/mtd1ro /dev/mtd3 /dev/mtd4ro >>>>>>> /dev/mtdblock2 >>>>>>> /dev/mtd0ro /dev/mtd2 /dev/mtd3ro /dev/mtdblock0 >>>>>>> /dev/mtdblock3 >>>>>>> /dev/mtd1 /dev/mtd2ro /dev/mtd4 /dev/mtdblock1 >>>>>>> /dev/mtdblock4 >>>>>>> >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to [email protected]. >>>>>> >>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> LinkedIn - http://www.linkedin.com/in/maximpodbereznyy >>>>> Company - http://www.linkedin.com/company/mentorel >>>>> Facebook - https://www.facebook.com/mentorel.company >>>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> >>> >>> -- >>> LinkedIn - http://www.linkedin.com/in/maximpodbereznyy >>> Company - http://www.linkedin.com/company/mentorel >>> Facebook - https://www.facebook.com/mentorel.company >>> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected] <javascript:>. >> For more options, visit https://groups.google.com/d/optout. >> > > > > -- > LinkedIn - http://www.linkedin.com/in/maximpodbereznyy > Company - http://www.linkedin.com/company/mentorel > Facebook - https://www.facebook.com/mentorel.company > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
