I attached my dmesg logs in the case it could be usefull. On Tuesday, 8 July 2014 20:47:48 UTC-4, hmc wrote: > > Hi, > > I used to work with usb audio sound card without any problem on the > Beagleboard-xM, image bbxm-ubuntu-14.04-2014-04-18-2gb.img.xz. > The only important step was to install alsa, via apt-get. > > I recently switched to beaglebone black and I am having some trouble > bringing up the same audio cards on the Ubuntu > image bone-ubuntu-14.04-console-2014-06-05-2gb.img.xz. I am using the exact > same steps and added lines to load the kernel modules in /etc/modules. > I end up with lsmod giving me: > > ubuntu@arm:~$ lsmod > Module Size Used by > g_multi 51145 0 > libcomposite 14931 1 g_multi > snd_seq_oss 28680 0 > snd_seq_midi 4792 0 > snd_seq_midi_event 5632 2 snd_seq_oss,snd_seq_midi > snd_seq 47273 5 > snd_seq_midi_event,snd_seq_oss,snd_seq_midi > snd_seq_device 6138 3 snd_seq,snd_seq_oss,snd_seq_midi > snd_usb_audio 103930 0 > snd_hwdep 5264 1 snd_usb_audio > snd_usbmidi_lib 15302 1 snd_usb_audio > > lsusb gives me: > ubuntu@arm:~$ lsusb > Bus 001 Device 002: ID 0582:012f Roland Corp. QUAD-CAPTURE > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > where Roland Corp. QUAD-CAPTURE does match the tested sound card. > > Sadly, the card does not get listed in /proc > ubuntu@arm:~$ cat /proc/asound/cards > 0 [Black ]: TI_BeagleBone_B - TI BeagleBone Black > TI BeagleBone Black > where I would expect to see my QUAD-CAPTURE card at index 1. > I tested with a sound card from another manufacturer and got the same > result. > > Any clue what could be going on? > Am I forgetting to load any kernel module? > Is something missing in the kernel? > Any hint on where to look at? (I am actually fairly new to Ubuntu dev) > > I did take a look at dmesg logs, which do not show anything obvious. > > > >
-- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
ubuntu@arm:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13-bone56 (root@imx6q-wandboard-2gb-0) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-19ubuntu1) ) #1 SMP Thu Jun 5 03:28:17 UTC 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 130816 [ 0.000000] free_area_init_node: node 0, pgdat c08a8e80, node_mem_map c0924000 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 129792 pages, LIFO batch:31 [ 0.000000] AM335X ES2.1 (l2cache sgx neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0d34000 s14080 r8192 d14592 u36864 [ 0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792 [ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 1048576 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 511MB = 511MB total [ 0.000000] Memory: 505024k/505024k available, 19264k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) [ 0.000000] .text : 0xc0008000 - 0xc07e3b58 (8047 kB) [ 0.000000] .init : 0xc07e4000 - 0xc0823700 ( 254 kB) [ 0.000000] .data : 0xc0824000 - 0xc08abe40 ( 544 kB) [ 0.000000] .bss : 0xc08abe40 - 0xc0923580 ( 478 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:0 nr_irqs:0 0 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000586] Calibrating delay loop... 993.47 BogoMIPS (lpj=969728) [ 0.029198] pid_max: default: 32768 minimum: 301 [ 0.029342] Security Framework initialized [ 0.029405] Mount-cache hash table entries: 512 [ 0.035262] Initializing cgroup subsys cpuacct [ 0.035306] Initializing cgroup subsys memory [ 0.035350] Initializing cgroup subsys blkio [ 0.035445] CPU: Testing write buffer coherency: ok [ 0.035829] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.035893] Setting up static identity map for 0x804c95f8 - 0x804c9644 [ 0.036800] Brought up 1 CPUs [ 0.036829] SMP: Total of 1 processors activated (993.47 BogoMIPS). [ 0.037625] devtmpfs: initialized [ 0.045996] omap_hwmod: wd_timer2: _wait_target_disable failed [ 0.098090] pinctrl core: initialized pinctrl subsystem [ 0.098240] rstctl core: initialized rstctl subsystem [ 0.098539] regulator-dummy: no parameters [ 0.098860] NET: Registered protocol family 16 [ 0.099398] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.104990] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.105580] platform 49000000.edma: alias fck already exists [ 0.105606] platform 49000000.edma: alias fck already exists [ 0.105627] platform 49000000.edma: alias fck already exists [ 0.106225] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.106318] OMAP GPIO hardware version 0.1 [ 0.107138] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.107852] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.108539] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.108790] of_get_named_gpio_flags exited with status 52 [ 0.108807] gpio-rctrl rstctl.4: loaded OK [ 0.111886] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.113107] cpsw.0: No hwaddr in dt. Using 1c:ba:8c:e4:91:17 from efuse [ 0.113139] cpsw.1: No hwaddr in dt. Using 1c:ba:8c:e4:91:19 from efuse [ 0.121149] bio: create slab <bio-0> at 0 [ 0.127380] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.127548] of_get_named_gpio_flags: can't parse gpios property [ 0.127667] vmmcsd_fixed: 3300 mV [ 0.129170] SCSI subsystem initialized [ 0.129413] usbcore: registered new interface driver usbfs [ 0.129480] usbcore: registered new interface driver hub [ 0.129675] usbcore: registered new device driver usb [ 0.130881] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 0.131793] input: tps65217_pwr_but as /devices/ocp.3/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 0.133023] DCDC1: at 1500 mV [ 0.133864] vdd_mpu: 925 <--> 1325 mV at 1325 mV [ 0.134693] vdd_core: 925 <--> 1150 mV at 1125 mV [ 0.135501] LDO1: at 1800 mV [ 0.136289] LDO2: at 3300 mV [ 0.137827] LDO3: 1800 mV [ 0.138667] LDO4: at 3300 mV [ 0.139383] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 0.139836] omap_i2c 44e0b000.i2c: unable to select pin group [ 0.140303] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz [ 0.141692] omap_i2c 4819c000.i2c: unable to select pin group [ 0.141854] media: Linux media interface: v0.10 [ 0.141927] Linux video capture interface: v2.00 [ 0.142007] pps_core: LinuxPPS API ver. 1 registered [ 0.142022] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]> [ 0.142422] Advanced Linux Sound Architecture Driver Initialized. [ 0.143068] NetLabel: Initializing [ 0.143090] NetLabel: domain hash size = 128 [ 0.143102] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.143173] NetLabel: unlabeled traffic allowed by default [ 0.143365] Switching to clocksource gp_timer [ 0.173442] NET: Registered protocol family 2 [ 0.174096] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.174193] TCP bind hash table entries: 4096 (order: 4, 81920 bytes) [ 0.174290] TCP: Hash tables configured (established 4096 bind 4096) [ 0.174357] TCP: reno registered [ 0.174377] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.174408] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.174652] NET: Registered protocol family 1 [ 0.175101] RPC: Registered named UNIX socket transport module. [ 0.175125] RPC: Registered udp transport module. [ 0.175139] RPC: Registered tcp transport module. [ 0.175152] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.175373] Trying to unpack rootfs image as initramfs... [ 0.380730] Freeing initrd memory: 3224K [ 0.381080] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.381342] CPU PMU: attempt to register multiple PMU devices! [ 0.381373] arm-pmu: probe of arm-pmu failed with error -28 [ 0.381781] omap2_mbox_probe: platform not supported [ 0.533851] VFS: Disk quotas dquot_6.5.2 [ 0.534021] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.534841] NFS: Registering the id_resolver key type [ 0.534937] Key type id_resolver registered [ 0.534953] Key type id_legacy registered [ 0.535229] fuse init (API version 7.20) [ 0.535623] Btrfs loaded [ 0.535739] msgmni has been set to 992 [ 0.537389] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.537427] io scheduler noop registered [ 0.537441] io scheduler deadline registered [ 0.537469] io scheduler cfq registered (default) [ 0.538623] tps65217-bl tps65217-bl: no platform data provided [ 0.538661] tps65217-bl: probe of tps65217-bl failed with error -22 [ 0.539186] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.540557] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 0.540842] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 1.292326] console [ttyO0] enabled [ 1.296620] [drm] Initialized drm 1.1.0 20060810 [ 1.308622] brd: module loaded [ 1.315543] loop: module loaded [ 1.318933] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.326155] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.333377] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.340602] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.347827] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.361681] bone-capemgr bone_capemgr.9: Baseboard: 'A335BNLT,000C,2414BBBK1669' [ 1.369435] bone-capemgr bone_capemgr.9: compatible-baseboard=ti,beaglebone-black [ 1.407120] bone-capemgr bone_capemgr.9: slot #0: No cape found [ 1.444227] bone-capemgr bone_capemgr.9: slot #1: No cape found [ 1.481335] bone-capemgr bone_capemgr.9: slot #2: No cape found [ 1.518445] bone-capemgr bone_capemgr.9: slot #3: No cape found [ 1.524661] bone-capemgr bone_capemgr.9: slot #4: specific override [ 1.531228] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 4 [ 1.539247] bone-capemgr bone_capemgr.9: slot #4: 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G' [ 1.549314] bone-capemgr bone_capemgr.9: slot #5: specific override [ 1.555873] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 5 [ 1.563883] bone-capemgr bone_capemgr.9: slot #5: 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI' [ 1.573844] bone-capemgr bone_capemgr.9: slot #6: specific override [ 1.580415] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 6 [ 1.588417] bone-capemgr bone_capemgr.9: slot #6: 'Bone-Black-HDMIN,00A0,Texas Instrument,BB-BONELT-HDMIN' [ 1.598816] bone-capemgr bone_capemgr.9: loader: before slot-4 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.607659] bone-capemgr bone_capemgr.9: loader: check slot-4 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.616448] bone-capemgr bone_capemgr.9: loader: before slot-5 BB-BONELT-HDMI:00A0 (prio 1) [ 1.625184] bone-capemgr bone_capemgr.9: loader: check slot-5 BB-BONELT-HDMI:00A0 (prio 1) [ 1.633851] bone-capemgr bone_capemgr.9: initialized OK. [ 1.639421] bone-capemgr bone_capemgr.9: loader: before slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.648243] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.658654] OneNAND driver initializing [ 1.663564] usbcore: registered new interface driver cdc_ether [ 1.669702] bone-capemgr bone_capemgr.9: loader: after slot-4 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.678500] usbcore: registered new interface driver rndis_host [ 1.684737] bone-capemgr bone_capemgr.9: loader: after slot-5 BB-BONELT-HDMI:00A0 (prio 1) [ 1.693395] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.702191] usbcore: registered new interface driver cdc_ncm [ 1.708133] bone-capemgr bone_capemgr.9: slot #4: Requesting firmware 'cape-bone-2g-emmc1.dtbo' for board-name 'Bone-LT-eMMC-2G', version '00A0' [ 1.722137] usbcore: registered new interface driver cdc_acm [ 1.728081] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.736448] Initializing USB Mass Storage driver... [ 1.741572] bone-capemgr bone_capemgr.9: slot #4: dtbo 'cape-bone-2g-emmc1.dtbo' loaded; converting to live tree [ 1.752233] bone-capemgr bone_capemgr.9: slot #5: Requesting firmware 'cape-boneblack-hdmi-00A0.dtbo' for board-name 'Bone-Black-HDMI', version '00A0' [ 1.766377] usbcore: registered new interface driver usb-storage [ 1.772661] USB Mass Storage support registered. [ 1.777687] bone-capemgr bone_capemgr.9: slot #4: #2 overlays [ 1.784296] bone-capemgr bone_capemgr.9: slot #4: Applied #2 overlays. [ 1.791144] bone-capemgr bone_capemgr.9: loader: done slot-4 BB-BONE-EMMC-2G:00A0 (prio 1) [ 1.799815] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.808577] bone-capemgr bone_capemgr.9: slot #5: dtbo 'cape-boneblack-hdmi-00A0.dtbo' loaded; converting to live tree [ 1.819906] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.826454] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 1.831669] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 1.840981] bone-capemgr bone_capemgr.9: slot #5: #4 overlays [ 1.848317] platform 4830e000.fb: alias fck already exists [ 1.854193] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 1.854205] musb-hdrc: MHDRC RTL version 2.0 [ 1.854214] musb-hdrc: setup fifo_mode 4 [ 1.854230] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 1.854325] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 1.859365] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 1.865548] bone-capemgr bone_capemgr.9: slot #5: Applied #4 overlays. [ 1.872442] bone-capemgr bone_capemgr.9: loader: done slot-5 BB-BONELT-HDMI:00A0 (prio 1) [ 1.881028] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.890212] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 1.895446] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 1.904207] bone-capemgr bone_capemgr.9: loader: after slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.912993] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 1.913004] musb-hdrc: MHDRC RTL version 2.0 [ 1.913012] musb-hdrc: setup fifo_mode 4 [ 1.913023] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 1.913095] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 1.918116] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 1.923401] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 1.929435] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware 'cape-boneblack-hdmin-00A0.dtbo' for board-name 'Bone-Black-HDMIN', version '00A0' [ 1.943796] bone-capemgr bone_capemgr.9: slot #6: dtbo 'cape-boneblack-hdmin-00A0.dtbo' loaded; converting to live tree [ 1.955351] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 1.963590] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 1.963665] usb usb1: default language 0x0409 [ 1.963696] usb usb1: udev 1, busnum 1, minor = 0 [ 1.963708] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.970843] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.978399] usb usb1: Product: MUSB HDRC host driver [ 1.983602] usb usb1: Manufacturer: Linux 3.8.13-bone56 musb-hcd [ 1.989884] usb usb1: SerialNumber: musb-hdrc.1.auto [ 1.995292] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN conflict P8.45 (#5:BB-BONELT-HDMI) [ 2.004888] bone-capemgr bone_capemgr.9: slot #6: Failed verification [ 2.011631] bone-capemgr bone_capemgr.9: loader: failed to load slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 2.021902] usb usb1: usb_probe_device [ 2.021918] usb usb1: configuration #1 chosen from 1 choice [ 2.021964] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.022065] hub 1-0:1.0: usb_probe_interface [ 2.022077] hub 1-0:1.0: usb_probe_interface - got id [ 2.022094] hub 1-0:1.0: USB hub found [ 2.026109] hub 1-0:1.0: 1 port detected [ 2.030239] hub 1-0:1.0: standalone hub [ 2.030249] hub 1-0:1.0: individual port power switching [ 2.030258] hub 1-0:1.0: no over-current protection [ 2.030267] hub 1-0:1.0: Single TT [ 2.030277] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 2.030286] hub 1-0:1.0: power on to power good time: 10ms [ 2.030309] hub 1-0:1.0: local power source is good [ 2.030366] hub 1-0:1.0: enabling power on all ports [ 2.030967] mousedev: PS/2 mouse device common for all mice [ 2.038384] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.045851] 44e3e000.rtc: already running [ 2.050223] i2c /dev entries driver [ 2.054841] pps_ldisc: PPS line discipline registered [ 2.060240] Driver for 1-wire Dallas network protocol. [ 2.066720] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.074350] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: [email protected] [ 2.083262] cpuidle: using governor ladder [ 2.087577] cpuidle: using governor menu [ 2.091933] of_get_named_gpio_flags exited with status 6 [ 2.091944] of_get_named_gpio_flags: can't parse gpios property [ 2.091952] of_get_named_gpio_flags: can't parse gpios property [ 2.091973] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed [ 2.099176] omap_hsmmc mmc.5: Failed to get rstctl; not using any [ 2.105834] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.112991] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.120251] mmc.5 supply vmmc_aux not found, using dummy regulator [ 2.127034] omap_hsmmc mmc.5: pins are not configured from the driver [ 2.133885] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 2.133930] hub 1-0:1.0: hub_suspend [ 2.133955] usb usb1: bus auto-suspend, wakeup 1 [ 2.161188] of_get_named_gpio_flags: can't parse gpios property [ 2.161203] of_get_named_gpio_flags: can't parse gpios property [ 2.161210] of_get_named_gpio_flags: can't parse gpios property [ 2.161242] gpio-rctrl rstctl.4: gpio_rctrl_request eMMC_RSTn [ 2.167381] omap_hsmmc mmc.11: Got rstctl (gpio:#0 name eMMC_RSTn) label:eMMC_RSTn [ 2.175342] gpio-rctrl rstctl.4: gpio_rctrl_deassert eMMC_RSTn [ 2.181660] edma-dma-engine edma-dma-engine.0: allocated channel for 0:3 [ 2.188740] edma-dma-engine edma-dma-engine.0: allocated channel for 0:2 [ 2.196094] mmc.11 supply vmmc_aux not found, using dummy regulator [ 2.202746] omap_hsmmc mmc.11: pins are not configured from the driver [ 2.237532] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8 [ 2.249197] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22 [ 2.256477] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single [ 2.265412] leds-gpio gpio-leds.8: pins are not configured from the driver [ 2.272609] of_get_named_gpio_flags exited with status 53 [ 2.272621] of_get_named_gpio_flags exited with status 54 [ 2.272631] of_get_named_gpio_flags exited with status 55 [ 2.272641] of_get_named_gpio_flags exited with status 56 [ 2.272653] of_get_named_gpio_flags exited with status 53 [ 2.272792] of_get_named_gpio_flags exited with status 54 [ 2.272900] of_get_named_gpio_flags exited with status 55 [ 2.272994] of_get_named_gpio_flags exited with status 56 [ 2.273317] ledtrig-cpu: registered to indicate activity on CPUs [ 2.279877] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 2.287049] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 2.294449] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.300657] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 2.307795] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 2.317800] usbcore: registered new interface driver usbhid [ 2.323700] usbhid: USB HID core driver [ 2.328571] ashmem: initialized [ 2.331991] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.340748] logger: created 256K log 'log_main' [ 2.345746] logger: created 256K log 'log_events' [ 2.350793] mmc0: new high speed SD card at address 07d8 [ 2.356547] logger: created 256K log 'log_radio' [ 2.361816] mmcblk0: mmc0:07d8 SD02G 1.83 GiB [ 2.366705] logger: created 256K log 'log_system' [ 2.372911] mmcblk0: p1 p2 [ 2.377084] of_get_named_gpio_flags exited with status 59 [ 2.378755] davinci_evm sound.14: nxp-hdmi-hifi <-> 48038000.mcasp mapping ok [ 2.388415] TCP: cubic registered [ 2.392021] NET: Registered protocol family 10 [ 2.397504] NET: Registered protocol family 17 [ 2.402469] Key type dns_resolver registered [ 2.407144] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.415255] ThumbEE CPU extension supported. [ 2.419771] Registering SWP/SWPB emulation handler [ 2.425465] registered taskstats version 1 [ 2.431463] of_get_named_gpio_flags: can't parse gpios property [ 2.431484] tilcdc 4830e000.fb: No power control GPIO [ 2.475779] mmc1: BKOPS_EN bit is not set [ 2.484423] mmc1: new high speed MMC card at address 0001 [ 2.490598] mmcblk1: mmc1:0001 MMC04G 3.65 GiB [ 2.495733] mmcblk1boot0: mmc1:0001 MMC04G partition 1 1.00 MiB [ 2.502140] mmcblk1boot1: mmc1:0001 MMC04G partition 2 1.00 MiB [ 2.510168] mmcblk1: p1 p2 [ 2.514870] mmcblk1boot1: unknown partition table [ 2.521372] mmcblk1boot0: unknown partition table [ 2.550202] tilcdc 4830e000.fb: found TDA19988 [ 2.555432] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 2.562356] [drm] No driver support for vblank timestamp query. [ 2.568822] tilcdc 4830e000.fb: No connectors reported connected with modes [ 2.576122] [drm] Cannot find any crtc or sizes - going 1024x768 [ 2.590998] Console: switching to colour frame buffer device 128x48 [ 2.603021] tilcdc 4830e000.fb: fb0: frame buffer device [ 2.608729] tilcdc 4830e000.fb: registered panic notifier [ 2.614445] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 2.668851] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.675328] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.687636] libphy: 4a101000.mdio: probed [ 2.691999] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.701876] Detected MACID = 1c:ba:8c:e4:91:17 [ 2.706547] cpsw 4a100000.ethernet: NAPI disabled [ 2.712951] omap_rtc 44e3e000.rtc: setting system clock to 2014-07-09 00:33:30 UTC (1404866010) [ 2.726576] ALSA device list: [ 2.729805] #0: TI BeagleBone Black [ 2.734295] Freeing init memory: 252K [ 2.823943] systemd-udevd[104]: starting version 204 [ 3.319605] usb usb1: usb wakeup-resume [ 3.319653] usb usb1: usb auto-resume [ 3.319672] hub 1-0:1.0: hub_resume [ 3.319706] hub 1-0:1.0: port 1: status 0101 change 0001 [ 3.422932] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 3.422979] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s [ 3.528832] usb 1-1: new high-speed USB device number 2 using musb-hdrc [ 3.668310] usb 1-1: skipped 1 descriptor after interface [ 3.668332] usb 1-1: skipped 2 descriptors after interface [ 3.668346] usb 1-1: skipped 1 descriptor after endpoint [ 3.668356] usb 1-1: skipped 2 descriptors after interface [ 3.668367] usb 1-1: skipped 1 descriptor after endpoint [ 3.668376] usb 1-1: skipped 2 descriptors after interface [ 3.668386] usb 1-1: skipped 1 descriptor after endpoint [ 3.668396] usb 1-1: skipped 2 descriptors after interface [ 3.668406] usb 1-1: skipped 1 descriptor after endpoint [ 3.668415] usb 1-1: skipped 2 descriptors after interface [ 3.668425] usb 1-1: skipped 1 descriptor after endpoint [ 3.668434] usb 1-1: skipped 2 descriptors after interface [ 3.668445] usb 1-1: skipped 1 descriptor after endpoint [ 3.668454] usb 1-1: skipped 2 descriptors after interface [ 3.668464] usb 1-1: skipped 1 descriptor after endpoint [ 3.668474] usb 1-1: skipped 2 descriptors after interface [ 3.668515] usb 1-1: skipped 1 descriptor after endpoint [ 3.668526] usb 1-1: skipped 1 descriptor after interface [ 3.668884] usb 1-1: default language 0x0409 [ 3.669161] usb 1-1: udev 2, busnum 1, minor = 1 [ 3.669175] usb 1-1: New USB device found, idVendor=0582, idProduct=012f [ 3.678630] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.688354] usb 1-1: Product: QUAD-CAPTURE [ 3.694850] usb 1-1: Manufacturer: Roland [ 3.701249] usb 1-1: SerialNumber: 0000CF953E57FA5C0239922B0B08A0E8 [ 3.722320] usb 1-1: usb_probe_device [ 3.722344] usb 1-1: configuration #1 chosen from 1 choice [ 3.723409] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 3.723680] usb 1-1: adding 1-1:1.1 (config #1, interface 1) [ 3.723818] usb 1-1: adding 1-1:1.2 (config #1, interface 2) [ 3.724359] usb 1-1: adding 1-1:1.3 (config #1, interface 3) [ 3.724492] usb 1-1: adding 1-1:1.4 (config #1, interface 4) [ 3.724932] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 3.724965] hub 1-0:1.0: port 1 enable change, status 00000503 [ 4.706622] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 5.301445] init: plymouth-upstart-bridge main process (159) terminated with status 1 [ 5.314498] init: plymouth-upstart-bridge main process ended, respawning [ 5.421476] init: plymouth-upstart-bridge main process (169) terminated with status 1 [ 5.432304] init: plymouth-upstart-bridge main process ended, respawning [ 5.444634] init: ureadahead main process (162) terminated with status 5 [ 5.532763] init: plymouth-upstart-bridge main process (173) terminated with status 1 [ 5.544236] init: plymouth-upstart-bridge main process ended, respawning [ 6.711715] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ 8.613682] systemd-udevd[311]: starting version 204 [ 9.052165] usbcore: registered new interface driver snd-usb-audio [ 12.643871] init: avahi-cups-reload main process (411) terminated with status 1 [ 12.784625] net eth0: initializing cpsw version 1.12 (0) [ 12.792268] net eth0: phy found : id is : 0x7c0f1 [ 12.792304] libphy: PHY 4a101000.mdio:01 not found [ 12.797452] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 12.837673] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 15.868659] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 15.868721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 18.090492] gadget: using random self ethernet address [ 18.102304] usb0: MAC 86:06:27:f0:4a:55 [ 18.102322] usb0: HOST MAC 1c:ba:8c:e4:91:19 [ 18.111491] gadget: Mass Storage Function, version: 2009/09/11 [ 18.111516] gadget: Number of LUNs=1 [ 18.111540] lun0: LUN: removable file: /dev/mmcblk0p1 [ 18.111644] gadget: Multifunction Composite Gadget [ 18.111672] gadget: g_multi ready [ 18.111713] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver [ 18.112028] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 2 [ 18.112055] musb-hdrc musb-hdrc.0.auto: supports USB remote wakeup [ 18.112122] usb usb2: default language 0x0409 [ 18.112153] usb usb2: udev 1, busnum 2, minor = 128 [ 18.112164] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 18.112269] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 18.112281] usb usb2: Product: MUSB HDRC host driver [ 18.112291] usb usb2: Manufacturer: Linux 3.8.13-bone56 musb-hcd [ 18.112300] usb usb2: SerialNumber: musb-hdrc.0.auto [ 18.113615] usb usb2: usb_probe_device [ 18.113634] usb usb2: configuration #1 chosen from 1 choice [ 18.113682] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 18.113813] hub 2-0:1.0: usb_probe_interface [ 18.113825] hub 2-0:1.0: usb_probe_interface - got id [ 18.113885] hub 2-0:1.0: USB hub found [ 18.117759] hub 2-0:1.0: 1 port detected [ 18.117782] hub 2-0:1.0: standalone hub [ 18.117791] hub 2-0:1.0: individual port power switching [ 18.117801] hub 2-0:1.0: no over-current protection [ 18.117809] hub 2-0:1.0: Single TT [ 18.117820] hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 18.117830] hub 2-0:1.0: power on to power good time: 10ms [ 18.117855] hub 2-0:1.0: local power source is good [ 18.117945] hub 2-0:1.0: enabling power on all ports [ 18.217847] hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 18.217905] hub 2-0:1.0: hub_suspend [ 18.217933] usb usb2: bus auto-suspend, wakeup 1 [ 20.259650] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 21.467554] init: plymouth-upstart-bridge main process ended, respawning ubuntu@arm:~$ QUAD-CAPTUREQUAD-CAPTURE
