I followed the directions on http://elinux.org/BeagleBoardUbuntu to setup my BeagleBoard. I did the Flash first and then did the Linux. When it boots I get this: U-Boot 2014.07-00014-gae1db02 (Jul 22 2014 - 10:58:18), Build: jenkins-github_Bootloader-Builder-371 OMAP3530-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 128 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0 *** Warning - bad CRC, using default environment Beagle Rev Ax/Bx Timed out in wait_for_event: status=0000 Check if pads/pull-ups of bus 1 are properly configured No EEPROM on expansion board Timed out in wait_for_event: status=0000 Check if pads/pull-ups of bus 1 are properly configured No EEPROM on expansion board Die ID #311400020000000004013e8803024013 Net: usb_ether Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 Checking for: /uEnv.txt ... Checking for: /boot/uEnv.txt ... 44 bytes read in 30 ms (1000 Bytes/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... Running uname_boot ... loading /boot/vmlinuz-3.15.3-armv7-x4 ... 4678776 bytes read in 4259 ms (1 MiB/s) loading /boot/dtbs/3.15.3-armv7-x4/omap3-beagle.dtb ... 60325 bytes read in 215 ms (273.4 KiB/s) loading /boot/initrd.img-3.15.3-armv7-x4 ... 3659108 bytes read in 3314 ms (1.1 MiB/s) Kernel image @ 0x80300000 [ 0x000000 - 0x476478 ] ## Flattened Device Tree blob at 815f0000 Booting using the fdt blob at 0x815f0000 Loading Ramdisk to 86baf000, end 86f2c564 ... OK Using Device Tree in place at 815f0000, end 81601ba4 Starting kernel ... [ 2.040924] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slo t [ 3.038360] ehci-omap 48064800.ehci: Can't get PHY device for port 1: -517 [ 3.137084] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iv a [ 3.144775] omap2_set_init_voltage: unable to set vdd_mpu_iva [ 3.150909] omap2_set_init_voltage: unable to find boot up OPP for vdd_core [ 3.158294] omap2_set_init_voltage: unable to set vdd_core [ 3.184631] omap_i2c 48060000.i2c: timeout waiting on XUDF bit [ 4.177520] omap_i2c 48060000.i2c: controller timed out [ 4.226745] Error: Driver 'tfp410' is already registered, aborting... [ 4.361785] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 4.369476] sr_init: platform driver register failed for SR Scanning for Btrfs filesystems hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --debug option to see the details of our search for an access method. [ 6.005981] mmcblk0: error -84 transferring data, sector 40960, nr 264, cmd response 0x900, card status 0xb00 [ 6.214813] mmcblk0: error -84 transferring data, sector 41224, nr 32, cmd response 0x900, card status 0xb00 Then it repeats the last two lines until I remove power from the beagleboard. Can anyone point me in the right direction? Yes I do realize that this is old hardware. Thanks.
-- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
