$ ifconfig
ral0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether e0:2a:82:1b:5a:6a
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
status: associated
re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 1c:c1:de:bc:13:b8
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (none)
status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether e0:2a:82:1b:5a:6a
inet 192.168.1.102 netmask 0xffffff00 broadcast 192.168.1.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet OFDM/54Mbps mode 11g
status: associated
ssid Yu channel 9 (2452 MHz 11g) bssid b0:b2:dc:35:77:1b
country US authmode WPA2/802.11i privacy ON deftxkey UNDEF
AES-CCM 2:128-bit txpower 0 bmiss 7 scanvalid 60 protmode CTS wme
roaming MANUAL
$ lsmod
lsmod: not found
William Hermans於 2014年9月5日星期五UTC+8上午4時58分42秒寫道：
>
> oh, and the output of lsmod.
>
>
> On Thu, Sep 4, 2014 at 1:57 PM, William Hermans <[email protected]
> <javascript:>> wrote:
>
>> the output of ifconfig would be immensely helpful. On the BSD side that
>> is.
>>
>>
>> On Thu, Sep 4, 2014 at 1:53 PM, Jason Kridner <[email protected]
>> <javascript:>> wrote:
>>
>>> On Thu, Sep 4, 2014 at 10:51 AM, <[email protected] <javascript:>>
>>> wrote:
>>>
>>>> I bought BBB today. It is a very cute board.After I install the drivers
>>>> this board provided, I can SSH to BeagleBone's IP Address through USB
>>>> cable on Windows 7. I have an FreeBSD 10 laptop, I try to SSH to
>>>> BeagleBone's IP Address through USB cable on FreeBSD but I can't. It shows
>>>> "ssh: connect to host 192.168.7.2 port 22: Operation timed out".
>>>> Should I install any driver on FreeBSD? Or What can I do to make it
>>>> works like on win 7?
>>>>
>>>
>>> Is your FreeBSD install newer than Feb 6, 2014 [1]?
>>> Can you share a kernel log that might indicate how the board was
>>> detected by FreeBSD?
>>> Do any network adapters show up for which you don't perform DHCP?
>>>
>>> [1] http://svnweb.freebsd.org/base?view=revision&revision=261541
>>>
>>>
>>>>
>>>> Thanks!
>>>>
>>>> --
>>>> For more options, visit http://beagleboard.org/discuss
>>>> ---
>>>> You received this message because you are subscribed to the Google
>>>> Groups "BeagleBoard" group.
>>>> To unsubscribe from this group and stop receiving emails from it, send
>>>> an email to [email protected] <javascript:>.
>>>> For more options, visit https://groups.google.com/d/optout.
>>>>
>>>
>>> --
>>> For more options, visit http://beagleboard.org/discuss
>>> ---
>>> You received this message because you are subscribed to the Google
>>> Groups "BeagleBoard" group.
>>> To unsubscribe from this group and stop receiving emails from it, send
>>> an email to [email protected] <javascript:>.
>>> For more options, visit https://groups.google.com/d/optout.
>>>
>>
>>
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
