Hi, Any updates on this topic? Even we are having the same issue..... Not able to test 10mbps mode in BeagleBoneBlack... Any suggestions is appreciated.
Thanks. On Wednesday, April 23, 2014 11:13:47 PM UTC+9, Mickae1 wrote: > > I tried too to use ethtool, but I got : > > Cannot get device coalesce settings > > I guess that the kernel is not compiled with : > > CONFIG_SWITCH_SET_PORT_CONFIG > > > > On Wed, Apr 23, 2014 at 4:05 PM, Jack Mitchell <[email protected] > <javascript:>> wrote: > >> You usually change this at the PHY level I believe, I've done it before >> using ethtool. >> >> Cheers, >> >> On 23/04/14 07:50, [email protected] <javascript:> wrote: >> > >> > Hi There - >> > >> > I'm trying to figure out how to change the eth0 port on a Beaglebone >> > Black to a specific port speed like 10Mbps. It appears now (see >> > below) that it is set to auto. Any assistance would be much >> appreciated. >> > >> > Tim >> > >> > >> > >> > root@beaglebone:/usr/lib/connman/test# ./get-services >> > [ /net/connman/service/ethernet_1cba8ca2bf39_cable ] >> > IPv6.Configuration = { Method=auto Privacy=disabled } >> > AutoConnect = true >> > Name = Wired >> > Nameservers = [ 8.8.8.8 8.8.4.4 ] >> > Provider = { } >> > Favorite = true >> > Domains.Configuration = [ ] >> > Timeservers.Configuration = dbus.Array([], >> > signature=dbus.Signature('s'), variant_level=1) >> > State = online >> > Proxy = { Method=direct } >> > Nameservers.Configuration = [ 8.8.8.8 8.8.4.4 ] >> > IPv4 = { Netmask=255.255.255.0 Gateway=192.168.1.1 Method=manual >> > Address=192.168.1.10 } >> > Timeservers = dbus.Array([dbus.String(u'192.168.1.1')], >> > signature=dbus.Signature('s'), variant_level=1) >> > IPv6 = { } >> > Domains = [ ] >> > Ethernet = { Interface=eth0 MTU=1500 Method=auto >> > Address=1C:BA:8C:A2:BF:39 } >> > Security = [ ] >> > Proxy.Configuration = { } >> > Type = ethernet >> > Immutable = false >> > IPv4.Configuration = { Netmask=255.255.255.0 Gateway=192.168.1.1 >> > Method=manual Address=192.168.1.10 } >> > >> > root@beaglebone:/usr/lib/connman/test# >> > >> > -- >> > For more options, visit http://beagleboard.org/discuss >> > --- >> > You received this message because you are subscribed to the Google >> > Groups "BeagleBoard" group. >> > To unsubscribe from this group and stop receiving emails from it, send >> > an email to [email protected] <javascript:> >> > <mailto:[email protected] <javascript:>>. >> > For more options, visit https://groups.google.com/d/optout. >> >> >> -- >> Jack Mitchell ([email protected] <javascript:>) >> Embedded Systems Engineer >> Cambridgeshire, UK >> http://www.embed.me.uk >> -- >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected] <javascript:>. >> For more options, visit https://groups.google.com/d/optout. >> > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
