Per beginner instructions, I tried to update Angstrom on my new BBB. The user lights appeared to be working correctly, but then froze with the middle two lit. I verified 5V 2.1A to the board and tried again. Same issue. So I tried booting off a Debian image. Same thing. After a couple minutes the two middle lights come on and the BBB freezes. I tried again with a new SD card. Same problem. I hooked up a serial monitor to the BBB and tried booting off SD with the following images:
Angstrom-Cloud9-IDE-GNOME-eglibc-ipk-v2012.12-beaglebone-2013.06.20.img BBB-eMMC-flasher-2013.09.04.img bone-debian-7.8-lxde-4gb-armhf-2015-03-01-4gb.img I can't boot with or without an SD card inserted, with or without an Ethernet connection I have nothing else plugged in. In all cases, in about 2 minutes the BBB freezes with the 2 middle user lights on. I hooked a serial monitor up to the debug port and tried booting off the Angstrom image. I got the following: [SERIAL/DIRECT] CONNECTED TO PORT COM15 (115200-8N1) รพ U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 33 bytes read in 3 ms (10.7 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... gpio: pin 55 (gpio 55) value is 1 4270840 bytes read in 772 ms (5.3 MiB/s) gpio: pin 56 (gpio 56) value is 1 24129 bytes read in 49 ms (480.5 KiB/s) Booting from mmc ... ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Angstrom/3.8.13/beaglebone Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4270776 Bytes = 4.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 80f80000 Booting using the fdt blob at 0x80f80000 XIP Kernel Image ... OK OK Using Device Tree in place at 80f80000, end 80f88e40 Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.194413] omap2_mbox_probe: platform not supported [ 0.204986] tps65217-bl tps65217-bl: no platform data provided [ 0.281517] bone-capemgr bone_capemgr.8: slot #0: No cape found [ 0.318623] bone-capemgr bone_capemgr.8: slot #1: No cape found [ 0.355732] bone-capemgr bone_capemgr.8: slot #2: No cape found [ 0.392841] bone-capemgr bone_capemgr.8: slot #3: No cape found [ 0.412837] bone-capemgr bone_capemgr.8: slot #6: BB-BONELT-HDMIN conflict P8.45 (#5:BB-BONELT-HDMI) [ 0.422453] bone-capemgr bone_capemgr.8: slot #6: Failed verification [ 0.429227] bone-capemgr bone_capemgr.8: loader: failed to load slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 0.451874] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 0.516308] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.7 [ 0.528019] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -22 [ 0.535334] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single systemd-fsck[85]: Angstrom: clean, 50489/218160 files, 302293/872448 blocks [ 39.015768] systemd-udevd[134]: timeout: killing '/sbin/modprobe usb:v1D6Bp0002d0308dc09dsc00dp01ic09isc00ip00in00' [327] [ 39.219188] systemd-udevd[114]: timeout: killing '/sbin/modprobe usb:v1D6Bp0002d0308dc09dsc00dp01ic09isc00ip00in00' [333] [ 40.027974] systemd-udevd[134]: timeout: killing '/sbin/modprobe usb:v1D6Bp0002d0308dc09dsc00dp01ic09isc00ip00in00' [327] [ 40.231227] systemd-udevd[114]: timeout: killing '/sbin/modprobe usb:v1D6Bp0002d0308dc09dsc00dp01ic09isc00ip00in00' [333] [ 40.672519] systemd-udevd[92]: worker [111] /devices/ocp.2/mmc.4/mmc_host/mmc0/mmc0:aaaa/block/mmcblk0 timeout; kill it [ 40.684890] systemd-udevd[92]: seq 1077 '/devices/ocp.2/mmc.4/mmc_host/mmc0/mmc0:aaaa/block/mmcblk0' killed [ 40.695381] systemd-udevd[92]: worker [114] /devices/ocp.2/47400000.usb/musb-hdrc.0.auto/usb2/2-0:1.0 timeout; kill it [ 40.707502] systemd-udevd[92]: seq 1376 '/devices/ocp.2/47400000.usb/musb-hdrc.0.auto/usb2/2-0:1.0' killed [ 40.717823] systemd-udevd[92]: worker [134] /devices/ocp.2/47400000.usb/musb-hdrc.1.auto/usb1/1-0:1.0 timeout; kill it [ 40.730068] systemd-udevd[92]: seq 1030 '/devices/ocp.2/47400000.usb/musb-hdrc.1.auto/usb1/1-0:1.0' killed [ 40.746648] systemd-udevd[92]: worker [111] terminated by signal 9 (Killed) [ 40.754287] systemd-udevd[92]: worker [114] terminated by signal 9 (Killed) [ 40.761741] systemd-udevd[92]: worker [134] terminated by signal 9 (Killed) [ 70.790371] systemd-udevd[92]: worker [106] /devices/ocp.2/mmc.4/mmc_host/mmc0/mmc0:aaaa/block/mmcblk0/mmcblk0p1 timeout; kill it [ 70.803712] systemd-udevd[92]: seq 1078 '/devices/ocp.2/mmc.4/mmc_host/mmc0/mmc0:aaaa/block/mmcblk0/mmcblk0p1' killed [ 70.815101] systemd-udevd[92]: worker [107] /devices/ocp.2/mmc.4/mmc_host/mmc0/mmc0:aaaa/block/mmcblk0/mmcblk0p2 timeout; kill it [ 70.828441] systemd-udevd[92]: seq 1079 '/devices/ocp.2/mmc.4/mmc_host/mmc0/mmc0:aaaa/block/mmcblk0/mmcblk0p2' killed [ 70.840395] systemd-udevd[92]: worker [106] terminated by signal 9 (Killed) [ 70.847837] systemd-udevd[92]: worker [107] terminated by signal 9 (Killed) [ 120.197537] INFO: task mmcqd/0:72 blocked for more than 60 seconds. [ 120.204111] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 120.212321] Kernel panic - not syncing: hung_task: blocked tasks [ 120.218610] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c036c641>] (panic+0x55/0x14c) [ 120.227145] [<c036c641>] (panic+0x55/0x14c) from [<c00617b3>] (watchdog+0x153/0x1a0) [ 120.235228] [<c00617b3>] (watchdog+0x153/0x1a0) from [<c003ca4b>] (kthread+0x61/0x72) [ 120.243395] [<c003ca4b>] (kthread+0x61/0x72) from [<c000c6fd>] (ret_from_fork+0x11/0x34) [ 120.251832] drm_kms_helper: panic occurred, switching back to text console Any idea what is wrong or how to fix it? I don't think my new BBB was DOA, so I assume I am doing something wrong here. After 2 days on this I have run out of options. Thanks. -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
