You need to register. Otherwise, your posts are moderated. Gerald
On Fri, Apr 24, 2015 at 8:27 PM, <[email protected]> wrote: > I'm trying to post this again. not sure why my previous post is not > showing up. > > I've been trying to flash my BBB for a few days. Tried the 2gb and 4gb > debian emmc flasher images from > > I formatted using the HP utility and FAT32 (NTFS was the only other > option). I used the 5v plug and held down the boot/user button. At first > everything looks ok with the wave LED pattern. About 10 minutes into it, > user LED 1 is the only one still on (solid). > > this is the dump from serial > > > U-Boot SPL 2015.01-00001-gb2412df (Jan 29 2015 - 15:01:06) > > > U-Boot 2015.01-00001-gb2412df (Jan 29 2015 - 15:01:06), Build: > jenkins-github_Bootloader-Builder-105 > > Watchdog enabled > I2C: ready > DRAM: 512 MiB > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > Using default environment > > Net: <ethaddr> not set. Validating first E-fuse MAC > cpsw > Hit any key to stop autoboot: 0 > gpio: pin 53 (gpio 53) value is 1 > switch to partitions #0, OK > mmc0 is current device > gpio: pin 54 (gpio 54) value is 1 > Checking for: /uEnv.txt ... > 933 bytes read in 9 ms (100.6 KiB/s) > gpio: pin 55 (gpio 55) value is 1 > Loaded environment from uEnv.txt > Importing environment from mmc ... > Checking if uenvcmd is set ... > gpio: pin 56 (gpio 56) value is 1 > Running uenvcmd ... > 718 bytes read in 53 ms (12.7 KiB/s) > 5617184 bytes read in 354 ms (15.1 MiB/s) > 2287175 bytes read in 174 ms (12.5 MiB/s) > 26098 bytes read in 81 ms (314.5 KiB/s) > Kernel image @ 0x82000000 [ 0x000000 - 0x55b620 ] > ## Flattened Device Tree blob at 88000000 > Booting using the fdt blob at 0x88000000 > Using Device Tree in place at 88000000, end 880095f1 > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > [ 0.000000] Booting Linux on physical CPU 0x0 > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 3.8.13-bone70 (root@a5-imx6q-wandboard-2gb) > (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Fri Jan 23 02:15:42 UTC 2015 > [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), > cr=50c5387d > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing > instruction cache > [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI > AM335x BeagleBone > [ 0.000000] Memory policy: ECC disabled, Data cache writeback > [ 0.000000] AM335X ES2.1 (l2cache sgx neon ) > [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0d4e000 s14080 r8192 d14592 > u36864 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 129792 > [ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8 > root=/dev/mmcblk0p1 rootfstype=ext4 rootwait fixrtc > init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh > [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 > bytes) > [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 > bytes) > [ 0.000000] __ex_table already sorted, skipping sort > [ 0.000000] allocated 1048576 bytes of page_cgroup > [ 0.000000] please try 'cgroup_disable=memory' option if you don't want > memory cgroups > [ 0.000000] Memory: 511MB = 511MB total > [ 0.000000] Memory: 505912k/505912k available, 18376k reserved, 0K > highmem > [ 0.000000] Virtual kernel memory layout: > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) > [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) > [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) > [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB) > [ 0.000000] .text : 0xc0008000 - 0xc07fda30 (8151 kB) > [ 0.000000] .init : 0xc07fe000 - 0xc083b700 ( 246 kB) > [ 0.000000] .data : 0xc083c000 - 0xc08c3980 ( 543 kB) > [ 0.000000] .bss : 0xc08c3980 - 0xc093d140 ( 486 kB) > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. > [ 0.000000] NR_IRQS:0 nr_irqs:0 0 > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 > interrupts > [ 0.000000] Total of 128 interrupts on 1 active controller > [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz > [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every > 178956ms > [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz > [ 0.000000] Console: colour dummy device 80x30 > [ 0.000000] console [tty0] enabled > [ 0.000639] Calibrating delay loop... 993.47 BogoMIPS (lpj=969728) > [ 0.029191] pid_max: default: 32768 minimum: 301 > [ 0.029338] Security Framework initialized > [ 0.029403] Mount-cache hash table entries: 512 > [ 0.035145] Initializing cgroup subsys cpuacct > [ 0.035191] Initializing cgroup subsys memory > [ 0.035238] Initializing cgroup subsys blkio > [ 0.035330] CPU: Testing write buffer coherency: ok > [ 0.035725] CPU0: thread -1, cpu 0, socket -1, mpidr 0 > [ 0.035793] Setting up static identity map for 0x804d4d08 - 0x804d4d54 > [ 0.036715] Brought up 1 CPUs > [ 0.036745] SMP: Total of 1 processors activated (993.47 BogoMIPS). > [ 0.037547] devtmpfs: initialized > [ 0.045872] omap_hwmod: wd_timer2: _wait_target_disable failed > [ 0.097997] pinctrl core: initialized pinctrl subsystem > [ 0.098151] rstctl core: initialized rstctl subsystem > [ 0.098434] regulator-dummy: no parameters > [ 0.098761] NET: Registered protocol family 16 > [ 0.099292] DMA: preallocated 256 KiB pool for atomic coherent > allocations > [ 0.104892] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 > size 568 > [ 0.105527] platform 49000000.edma: alias fck already exists > [ 0.105557] platform 49000000.edma: alias fck already exists > [ 0.105578] platform 49000000.edma: alias fck already exists > [ 0.106298] OMAP GPIO hardware version 0.1 > [ 0.108826] gpio-rctrl rstctl.4: loaded OK > [ 0.112207] No ATAGs? > [ 0.112233] hw-breakpoint: debug architecture 0x4 unsupported. > [ 0.113527] cpsw.0: No hwaddr in dt. Using 78:a5:04:bc:d6:16 from efuse > [ 0.113563] cpsw.1: No hwaddr in dt. Using 78:a5:04:bc:d6:18 from efuse > [ 0.121624] bio: create slab <bio-0> at 0 > [ 0.127879] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver > [ 0.128185] vmmcsd_fixed: 3300 mV > [ 0.129790] SCSI subsystem initialized > [ 0.130044] usbcore: registered new interface driver usbfs > [ 0.130113] usbcore: registered new interface driver hub > [ 0.130325] usbcore: registered new device driver usb > [ 0.131595] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz > [ 0.132507] input: tps65217_pwr_but as > /devices/ocp.3/44e0b000.i2c/i2c-0/0-0024/input/input0 > [ 0.134123] DCDC1: at 1500 mV > [ 0.134987] vdd_mpu: 925 <--> 1325 mV at 1325 mV > [ 0.135807] vdd_core: 925 <--> 1150 mV at 1125 mV > [ 0.136663] LDO1: at 1800 mV > [ 0.137461] LDO2: at 3300 mV > [ 0.138952] LDO3: 1800 mV > [ 0.139764] LDO4: at 3300 mV > [ 0.140480] tps65217 0-0024: TPS65217 ID 0xe version 1.2 > [ 0.140986] omap_i2c 44e0b000.i2c: unable to select pin group > [ 0.141466] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz > [ 0.142911] omap_i2c 4819c000.i2c: unable to select pin group > [ 0.143077] media: Linux media interface: v0.10 > [ 0.143147] Linux video capture interface: v2.00 > [ 0.143223] pps_core: LinuxPPS API ver. 1 registered > [ 0.143240] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo > Giometti <[email protected]> > [ 0.143278] PTP clock support registered > [ 0.143671] Advanced Linux Sound Architecture Driver Initialized. > [ 0.144269] NetLabel: Initializing > [ 0.144290] NetLabel: domain hash size = 128 > [ 0.144303] NetLabel: protocols = UNLABELED CIPSOv4 > [ 0.144378] NetLabel: unlabeled traffic allowed by default > [ 0.144669] Switching to clocksource gp_timer > [ 0.175934] NET: Registered protocol family 2 > [ 0.176653] TCP established hash table entries: 4096 (order: 3, 32768 > bytes) > [ 0.176751] TCP bind hash table entries: 4096 (order: 4, 81920 bytes) > [ 0.176840] TCP: Hash tables configured (established 4096 bind 4096) > [ 0.176912] TCP: reno registered > [ 0.176933] UDP hash table entries: 256 (order: 1, 12288 bytes) > [ 0.176965] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) > [ 0.177210] NET: Registered protocol family 1 > [ 0.177607] RPC: Registered named UNIX socket transport module. > [ 0.177637] RPC: Registered udp transport module. > [ 0.177651] RPC: Registered tcp transport module. > [ 0.177664] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 0.177892] Trying to unpack rootfs image as initramfs... > [ 0.339459] Freeing initrd memory: 2232K > [ 0.339804] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 > counters available > [ 0.340167] CPU PMU: attempt to register multiple PMU devices! > [ 0.340200] arm-pmu: probe of arm-pmu failed with error -28 > [ 0.340516] omap2_mbox_probe: platform not supported > [ 0.490833] VFS: Disk quotas dquot_6.5.2 > [ 0.491000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 0.491721] NFS: Registering the id_resolver key type > [ 0.491804] Key type id_resolver registered > [ 0.491820] Key type id_legacy registered > [ 0.492105] fuse init (API version 7.20) > [ 0.492600] Btrfs loaded > [ 0.492733] msgmni has been set to 992 > [ 0.494325] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 248) > [ 0.494443] io scheduler noop registered > [ 0.494462] io scheduler deadline registered > [ 0.494493] io scheduler cfq registered (default) > [ 0.495642] tps65217-bl tps65217-bl: no platform data provided > [ 0.495682] tps65217-bl: probe of tps65217-bl failed with error -22 > [ 0.496215] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > [ 0.497611] omap_uart 44e09000.serial: did not get pins for uart0 > error: -19 > [ 0.497909] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 72) is a > OMAP UART0 > [ 1.259660] console [ttyO0] enabled > [ 1.264028] [drm] Initialized drm 1.1.0 20060810 > [ 1.276144] brd: module loaded > [ 1.283081] loop: module loaded > [ 1.286483] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 > bytes/write > [ 1.293725] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 > bytes/write > [ 1.300960] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 > bytes/write > [ 1.308180] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 > bytes/write > [ 1.315408] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 > bytes/write > [ 1.329284] bone-capemgr bone_capemgr.9: Baseboard: > 'A335BNLT,00C0,2414BBBK2043' > [ 1.337097] bone-capemgr bone_capemgr.9: > compatible-baseboard=ti,beaglebone-black > [ 1.375216] bone-capemgr bone_capemgr.9: slot #0: No cape found > [ 1.412322] bone-capemgr bone_capemgr.9: slot #1: No cape found > [ 1.449432] bone-capemgr bone_capemgr.9: slot #2: No cape found > [ 1.486540] bone-capemgr bone_capemgr.9: slot #3: No cape found > [ 1.492765] bone-capemgr bone_capemgr.9: slot #4: specific override > [ 1.499331] bone-capemgr bone_capemgr.9: bone: Using override eeprom > data at slot 4 > [ 1.507340] bone-capemgr bone_capemgr.9: slot #4: > 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G' > [ 1.517405] bone-capemgr bone_capemgr.9: slot #5: specific override > [ 1.523974] bone-capemgr bone_capemgr.9: bone: Using override eeprom > data at slot 5 > [ 1.531987] bone-capemgr bone_capemgr.9: slot #5: > 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI' > [ 1.541973] bone-capemgr bone_capemgr.9: slot #6: specific override > [ 1.548544] bone-capemgr bone_capemgr.9: bone: Using override eeprom > data at slot 6 > [ 1.556561] bone-capemgr bone_capemgr.9: slot #6: > 'Bone-Black-HDMIN,00A0,Texas Instrument,BB-BONELT-HDMIN' > [ 1.566952] bone-capemgr bone_capemgr.9: loader: before slot-4 > BB-BONE-EMMC-2G:00A0 (prio 1) > [ 1.575797] bone-capemgr bone_capemgr.9: loader: check slot-4 > BB-BONE-EMMC-2G:00A0 (prio 1) > [ 1.584609] bone-capemgr bone_capemgr.9: loader: before slot-5 > BB-BONELT-HDMI:00A0 (prio 1) > [ 1.593345] bone-capemgr bone_capemgr.9: loader: check slot-5 > BB-BONELT-HDMI:00A0 (prio 1) > [ 1.602002] bone-capemgr bone_capemgr.9: initialized OK. > [ 1.607568] bone-capemgr bone_capemgr.9: loader: before slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.616399] bone-capemgr bone_capemgr.9: loader: check slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.626587] OneNAND driver initializing > [ 1.631555] usbcore: registered new interface driver cdc_ether > [ 1.637700] bone-capemgr bone_capemgr.9: loader: after slot-4 > BB-BONE-EMMC-2G:00A0 (prio 1) > [ 1.646489] usbcore: registered new interface driver rndis_host > [ 1.652738] bone-capemgr bone_capemgr.9: loader: after slot-5 > BB-BONELT-HDMI:00A0 (prio 1) > [ 1.661396] bone-capemgr bone_capemgr.9: loader: check slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.670206] usbcore: registered new interface driver cdc_ncm > [ 1.676153] bone-capemgr bone_capemgr.9: slot #4: Requesting firmware > 'cape-bone-2g-emmc1.dtbo' for board-name 'Bone-LT-eMMC-2G', version '00A0' > [ 1.690155] usbcore: registered new interface driver cdc_acm > [ 1.696097] cdc_acm: USB Abstract Control Model driver for USB modems > and ISDN adapters > [ 1.704460] Initializing USB Mass Storage driver... > [ 1.709582] bone-capemgr bone_capemgr.9: slot #4: dtbo > 'cape-bone-2g-emmc1.dtbo' loaded; converting to live tree > [ 1.720264] bone-capemgr bone_capemgr.9: slot #5: Requesting firmware > 'cape-boneblack-hdmi-00A0.dtbo' for board-name 'Bone-Black-HDMI', version > '00A0' > [ 1.734426] usbcore: registered new interface driver usb-storage > [ 1.740710] USB Mass Storage support registered. > [ 1.745746] bone-capemgr bone_capemgr.9: slot #4: #2 overlays > [ 1.752372] bone-capemgr bone_capemgr.9: slot #4: Applied #2 overlays. > [ 1.759224] bone-capemgr bone_capemgr.9: loader: done slot-4 > BB-BONE-EMMC-2G:00A0 (prio 1) > [ 1.767906] bone-capemgr bone_capemgr.9: loader: check slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.776671] bone-capemgr bone_capemgr.9: slot #5: dtbo > 'cape-boneblack-hdmi-00A0.dtbo' loaded; converting to live tree > [ 1.788004] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) > [ 1.794578] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 > [ 1.799801] musb-hdrc musb-hdrc.0.auto: > drivers/usb/musb/musb_dsps.c:480 dsps_musb_init: OK > [ 1.809112] bone-capemgr bone_capemgr.9: slot #5: #4 overlays > [ 1.816502] platform 4830e000.fb: alias fck already exists > [ 1.822559] musb-hdrc musb-hdrc.0.auto: *** mode=3 > [ 1.827615] musb-hdrc musb-hdrc.0.auto: *** power=250 > [ 1.833861] bone-capemgr bone_capemgr.9: slot #5: Applied #4 overlays. > [ 1.840766] bone-capemgr bone_capemgr.9: loader: done slot-5 > BB-BONELT-HDMI:00A0 (prio 1) > [ 1.849367] bone-capemgr bone_capemgr.9: loader: check slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.858558] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 > [ 1.863793] musb-hdrc musb-hdrc.1.auto: > drivers/usb/musb/musb_dsps.c:480 dsps_musb_init: OK > [ 1.872621] bone-capemgr bone_capemgr.9: loader: after slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.881519] musb-hdrc musb-hdrc.1.auto: *** mode=1 > [ 1.886551] musb-hdrc musb-hdrc.1.auto: *** power=250 > [ 1.891850] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver > [ 1.897893] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware > 'cape-boneblack-hdmin-00A0.dtbo' for board-name 'Bone-Black-HDMIN', version > '00A0' > [ 1.912439] musb-hdrc musb-hdrc.1.auto: new USB bus registered, > assigned bus number 1 > [ 1.920793] usb usb1: New USB device found, idVendor=1d6b, > idProduct=0002 > [ 1.927916] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 1.935474] usb usb1: Product: MUSB HDRC host driver > [ 1.940670] usb usb1: Manufacturer: Linux 3.8.13-bone70 musb-hcd > [ 1.946958] usb usb1: SerialNumber: musb-hdrc.1.auto > [ 1.952204] bone-capemgr bone_capemgr.9: slot #6: dtbo > 'cape-boneblack-hdmin-00A0.dtbo' loaded; converting to live tree > [ 1.964083] hub 1-0:1.0: USB hub found > [ 1.968065] hub 1-0:1.0: 1 port detected > [ 1.972383] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN > conflict P8.45 (#5:BB-BONELT-HDMI) > [ 1.981952] bone-capemgr bone_capemgr.9: slot #6: Failed verification > [ 1.988701] bone-capemgr bone_capemgr.9: loader: failed to load slot-6 > BB-BONELT-HDMIN:00A0 (prio 2) > [ 1.999042] mousedev: PS/2 mouse device common for all mice > [ 2.006741] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as > rtc0 > [ 2.014398] i2c /dev entries driver > [ 2.019044] pps_ldisc: PPS line discipline registered > [ 2.024615] Driver for 1-wire Dallas network protocol. > [ 2.031219] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 > sec > [ 2.038907] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) > initialised: [email protected] > [ 2.047814] cpuidle: using governor ladder > [ 2.052146] cpuidle: using governor menu > [ 2.056576] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' > failed > [ 2.063792] omap_hsmmc mmc.5: Failed to get rstctl; not using any > [ 2.070473] edma-dma-engine edma-dma-engine.0: allocated channel for > 0:25 > [ 2.077645] edma-dma-engine edma-dma-engine.0: allocated channel for > 0:24 > [ 2.084912] mmc.5 supply vmmc_aux not found, using dummy regulator > [ 2.091704] omap_hsmmc mmc.5: pins are not configured from the driver > [ 2.125459] gpio-rctrl rstctl.4: gpio_rctrl_request eMMC_RSTn > [ 2.131617] omap_hsmmc mmc.11: Got rstctl (gpio:#0 name eMMC_RSTn) > label:eMMC_RSTn > [ 2.139579] gpio-rctrl rstctl.4: gpio_rctrl_deassert eMMC_RSTn > [ 2.145905] edma-dma-engine edma-dma-engine.0: allocated channel for 0:3 > [ 2.153002] edma-dma-engine edma-dma-engine.0: allocated channel for 0:2 > [ 2.160398] mmc.11 supply vmmc_aux not found, using dummy regulator > [ 2.167056] omap_hsmmc mmc.11: pins are not configured from the driver > [ 2.201731] pinctrl-single 44e10800.pinmux: pin 44e10854 already > requested by 44e10800.pinmux; cannot claim for gpio-leds.8 > [ 2.213407] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status > -22 > [ 2.220690] pinctrl-single 44e10800.pinmux: could not request pin 21 on > device pinctrl-single > [ 2.229627] leds-gpio gpio-leds.8: pins are not configured from the > driver > [ 2.237559] ledtrig-cpu: registered to indicate activity on CPUs > [ 2.244144] edma-dma-engine edma-dma-engine.0: allocated channel for > 0:36 > [ 2.251340] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 > [ 2.258807] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 > [ 2.265031] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 > [ 2.272170] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 > [ 2.282173] usbcore: registered new interface driver usbhid > [ 2.288090] usbhid: USB HID core driver > [ 2.292991] ashmem: initialized > [ 2.296397] mmc0: host does not support reading read-only switch. > assuming write-enable. > [ 2.305110] logger: created 256K log 'log_main' > [ 2.310108] logger: created 256K log 'log_events' > [ 2.315166] mmc0: new high speed SDHC card at address aaaa > [ 2.321124] logger: created 256K log 'log_radio' > [ 2.326444] mmcblk0: mmc0:aaaa SU32G 29.7 GiB > [ 2.331322] logger: created 256K log 'log_system' > [ 2.337641] mmcblk0: p1 > [ 2.343098] davinci_evm sound.14: nxp-hdmi-hifi <-> 48038000.mcasp > mapping ok > [ 2.352804] TCP: cubic registered > [ 2.356421] NET: Registered protocol family 10 > [ 2.361901] NET: Registered protocol family 17 > [ 2.366870] Key type dns_resolver registered > [ 2.371533] VFP support v0.3: implementor 41 architecture 3 part 30 > variant c rev 3 > [ 2.379659] ThumbEE CPU extension supported. > [ 2.384175] Registering SWP/SWPB emulation handler > [ 2.389885] registered taskstats version 1 > [ 2.395980] tilcdc 4830e000.fb: No power control GPIO > [ 2.466945] mmc1: BKOPS_EN bit is not set > [ 2.475032] mmc1: new high speed MMC card at address 0001 > [ 2.481225] mmcblk1: mmc1:0001 MMC04G 3.60 GiB > [ 2.486204] mmcblk1boot0: mmc1:0001 MMC04G partition 1 2.00 MiB > [ 2.492619] mmcblk1boot1: mmc1:0001 MMC04G partition 2 2.00 MiB > [ 2.499885] mmcblk1: p1 > [ 2.504011] mmcblk1boot1: unknown partition table > [ 2.510337] mmcblk1boot0: unknown partition table > [ 2.517824] tilcdc 4830e000.fb: found TDA19988 > [ 2.523089] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). > [ 2.530051] [drm] No driver support for vblank timestamp query. > [ 2.536529] tilcdc 4830e000.fb: No connectors reported connected with > modes > [ 2.543865] [drm] Cannot find any crtc or sizes - going 1024x768 > [ 2.559426] Console: switching to colour frame buffer device 128x48 > [ 2.572107] tilcdc 4830e000.fb: fb0: frame buffer device > [ 2.577827] tilcdc 4830e000.fb: registered panic notifier > [ 2.583553] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 > [ 2.638896] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 > [ 2.645387] davinci_mdio 4a101000.mdio: detected phy mask fffffffe > [ 2.658305] libphy: 4a101000.mdio: probed > [ 2.662695] davinci_mdio 4a101000.mdio: phy[0]: device > 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 > [ 2.672604] Detected MACID = 78:a5:04:bc:d6:16 > [ 2.677294] cpsw 4a100000.ethernet: NAPI disabled > [ 2.684090] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 > 00:00:01 UTC (946684801) > [ 2.697948] ALSA device list: > [ 2.701175] #0: TI BeagleBone Black > [ 2.705700] Freeing init memory: 244K > Loading, please wait... > [ 2.761041] udevd[99]: starting version 175 > Begin: Loading essential drivers ... done. > Begin: Running /scripts/init-premount ... done. > Begin: Mounting root file system ... Begin: Running /scripts/local-top ... > done. > Begin: Running /scripts/local-premount ... done. > [ 4.027961] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data > mode. Opts: (null) > Begin: Running /scripts/local-bottom ... done. > done. > Begin: Running /scripts/init-bottom ... done. > Starting eMMC Flasher > ----------------------------- > Checking for Valid BBB EEPROM header > Valid BBB EEPROM header found > ----------------------------- > copying: [/dev/mmcblk0] -> [/dev/mmcblk1] > lsblk: > NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT > mmcblk1boot0 179:16 0 2M 1 disk > mmcblk1boot1 179:24 0 2M 1 disk > mmcblk0 179:0 0 29.7G 0 disk > `-mmcblk0p1 179:1 0 1.7G 0 part / > mmcblk1 179:8 0 3.6G 0 disk > `-mmcblk1p1 179:9 0 3.6G 0 part > ----------------------------- > df -h | grep rootfs: > df: cannot read table of mounted file systems: No such file or directory > ----------------------------- > Erasing: /dev/mmcblk1 > 108+0 records in > 108+0 records out > 113246208 bytes (113 MB) copied, 12.1734 s, 9.3 MB/s > 108+0 records in > 108+0 records out > 113246208 bytes (113 MB) copied, 3.59623 s, 31.5 MB/s > Erasing: /dev/mmcblk1 complete > ----------------------------- > Writing bootloader to [/dev/mmcblk1] > dd if=/opt/backup/uboot/MLO of=/dev/mmcblk1 count=1 seek=1 conv=notrunc > bs=128k > ----------------------------- > 0+1 records in > 0+1 records out > 73516 bytes (74 kB) copied, 0.0325348 s, 2.3 MB/s > ----------------------------- > dd if=/opt/backup/uboot/u-boot.img of=/dev/mmcblk1 count=2 seek=1 > conv=notrunc bs=384k > ----------------------------- > 1+1 records in > 1+1 records out > 393496 bytes (393 kB) copied, 0.0642242 s, 6.1 MB/s > ----------------------------- > Formatting: /dev/mmcblk1 > Checking that no[ 20.820281] mmcblk1: unknown partition table > -one is using this disk right now ... > OK > > Disk /dev/mmcblk1: [ 20.832956] mmcblk1: p1 > 118016 cylinders, 4 heads, 16 sectors/track > > sfdisk: ERROR: sector 3069678589 does not have an msdos signature > /dev/mmcblk1: unrecognized partition table type > Old situation: > No partitions found > New situation: > Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0 > > Device Boot Start End MiB #blocks Id System > /dev/mmcblk1p1 * 1 3687 3687 3775488 83 Linux > /dev/mmcblk1p2 0 - 0 0 0 Empty > /dev/mmcblk1p3 0 - 0 0 0 Empty > /dev/mmcblk1p4 0 - 0 0 0 Empty > Successfully wrote the new partition table > > Re-reading the partition table ... > > If you created or changed a DOS partition, /dev/foo7, say, then use dd(1) > to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1 > (See fdisk(8).) > mkfs.ext4 /dev/mmcblk1p1 -L BEAGLEBONE > ----------------------------- > mke2fs 1.42.5 (29-Jul-2012) > ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing > mtab file while determining whether /dev/mmcblk1p1 is mounted. > Discarding device blocks: done > Filesystem label=BEAGLEBONE > OS type: Linux > Block size=4096 (log=2) > Fragment size=4096 (log=2) > Stride=0 blocks, Stripe width=0 blocks > 236176 inodes, 943872 blocks > 47193 blocks (5.00%) reserved for the super user > First data block=0 > Maximum filesystem blocks=968884224 > 29 block groups > 32768 blocks per group, 32768 fragments per group > 8144 inodes per group > Superblock backups stored on blocks: > 32768, 98304, 163840, 229376, 294912, 819200, 884736 > > Allocating group tables: done > Writing inode tables: done > Creating journal (16384 blocks): done > Writing superblocks and filesystem accounting information: done > > ----------------------------- > Formatting: /dev/mmcblk1 complete > ----------------------------- > Copying: /dev/mmcblk0p1 -> /dev/mmcblk1p1 > [ 28.618582] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data > mode. Opts: (null) > rsync: / -> /tmp/rootfs/ > rsync: ignore the % values when shown as they are not accurate... > [ 120.488545] INFO: task mmcqd/0:71 blocked for more than 60 seconds. > [ 120.497457] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables > this message. > [ 120.507849] mmcqd/0 D c04d04a5 0 71 2 0x00000000 > [ 120.516796] Kernel panic - not syncing: hung_task: blocked tasks > [ 120.525299] [<c00114f1>] (unwind_backtrace+0x1/0x9c) from [<c04cb2fd>] > (panic+0x59/0x15c) > [ 120.536066] [<c04cb2fd>] (panic+0x59/0x15c) from [<c0073955>] > (watchdog+0x19d/0x1c0) > [ 120.546417] [<c0073955>] (watchdog+0x19d/0x1c0) from [<c00454eb>] > (kthread+0x6b/0x78) > [ 120.556893] [<c00454eb>] (kthread+0x6b/0x78) from [<c000c8fd>] > (ret_from_fork+0x11/0x34) > [ 120.567664] drm_kms_helper: panic occurred, switching back to text > console > > I'm not sure which version of BBB I have so I used the 2gb image last. Is > there any way to tell which version you have? Also since performing this > "flash" my BBB will no longer boot at all. > > thanks! > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- Gerald [email protected] http://beagleboard.org/ http://circuitco.com/support/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
