Hi William, I think you are right, there must be some sort of conflict on Riley’s system. BTW, 840 is connected to 888, so that pin might not be the best pin to test. Either way, I don’t understand why the Overlay manager doesn’t complain about a pin conflict.
Regards, John > On Nov 27, 2015, at 9:55 PM, William Hermans <[email protected]> wrote: > > OK so I thought maybe I forgot to copy the newly compiled overlay over . . . > > $ ls |grep pin > pinctrl-test-7-00A0.dtbo > pinctrl-test-7.dts > > $ rm pin* > $ ls |grep pin > < No output > > > $ cp /lib/firmware/pinctrl-test-7-00A0.dtbo . > $ dtc -I dtb -O dts pinctrl-test-7-00A0.dtbo > pinctrl-test-7-00A0.dts > > /dts-v1/; > > / { > compatible = "ti,beaglebone", "ti,beaglebone-black"; > part-number = "pinctrl-test-7"; > > fragment@0 { > target = <0xdeadbeef>; > > __overlay__ { > > pinctrl_test_7_pins { > pinctrl-single,pins = <0x40 0x27>; > linux,phandle = <0x1>; > phandle = <0x1>; > }; > }; > }; > > fragment@1 { > target = <0xdeadbeef>; > > __overlay__ { > > helper { > compatible = "gpio-of-helper"; > pinctrl-names = "default"; > pinctrl-0 = <0x1>; > status = "okay"; > linux,phandle = <0x2>; > phandle = <0x2>; > }; > }; > }; > > __symbols__ { > pinctrl_test = "/fragment@0/__overlay__/pinctrl_test_7_pins"; > test_helper = "/fragment@1/__overlay__/helper"; > }; > > __local_fixups__ { > > fragment@1 { > > __overlay__ { > > helper { > pinctrl-0 = <0x0>; > }; > }; > }; > }; > > __fixups__ { > am33xx_pinmux = "/fragment@0:target:0"; > ocp = "/fragment@1:target:0"; > }; > }; > > Ok, so this source mangling seems odd, but just looking things over, it seems > like it should work. Next, reboot, and reload, then see what happens. > > On Fri, Nov 27, 2015 at 10:40 PM, William Hermans <[email protected] > <mailto:[email protected]>> wrote: > Smells of a bug. But perhaps the GPIO pinmux's need to be explicity cleared > as I mentioned above ? > > On Fri, Nov 27, 2015 at 10:39 PM, William Hermans <[email protected] > <mailto:[email protected]>> wrote: > OK so I changed to this: > > fragment@0 { > target = <&am33xx_pinmux>; > __overlay__ { > pinctrl_test: pinctrl_test_7_pins { > pinctrl-single,pins = < > 0x040 0x27 // P9_15 PINS$16 GPIO1_16 = 48 Input Mode7 > pullup > >; > }; > }; > }; > > Compiled, copied, and then loaded the dtbo file. Then . . . > > $ dmesg |grep pinctrl-test-7 > [168784.685978] bone_capemgr bone_capemgr: part_number 'pinctrl-test-7', > version 'N/A' > [168784.706649] bone_capemgr bone_capemgr: slot #4: 'Override Board > Name,00A0,Override Manuf,pinctrl-test-7' > [168784.723188] bone_capemgr bone_capemgr: slot #4: dtbo > 'pinctrl-test-7-00A0.dtbo' loaded; overlay id #0 > [169658.533949] bone_capemgr bone_capemgr: part_number 'pinctrl-test-7', > version 'N/A' > [169658.554579] bone_capemgr bone_capemgr: slot #5: 'Override Board > Name,00A0,Override Manuf,pinctrl-test-7' > [169658.565013] bone_capemgr bone_capemgr: slot #5: dtbo > 'pinctrl-test-7-00A0.dtbo' loaded; overlay id #1 > > This shows that both device tree overlays have been sucessfully loaded. > Despite the fact that the previously overwritten overlay was never unloaded. > Then . . . > > $ sudo cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins |grep 840 > pin 16 (44e10840.0) 00000017 pinctrl-single > > So . . . > i$ cat /sys/devices/platform/bone_capemgr/slots > 0: PF---- -1 > 1: PF---- -1 > 2: PF---- -1 > 3: PF---- -1 > 4: P-O-L- 0 Override Board Name,00A0,Override Manuf,pinctrl-test-7 > 5: P-O-L- 1 Override Board Name,00A0,Override Manuf,pinctrl-test-7 > > oops, two overlays loaded lets see wha thappens when first one is unloaded. > > $ sudo sh -c "echo '-4' > /sys/devices/platform/bone_capemgr/slots" > $ cat /sys/devices/platform/bone_capemgr/slots > 0: PF---- -1 > 1: PF---- -1 > 2: PF---- -1 > 3: PF---- -1 > 5: P-O-L- 1 Override Board Name,00A0,Override Manuf,pinctrl-test-7 > $ sudo cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins |grep 840 > pin 16 (44e10840.0) 00000017 pinctrl-single > > Just as I thought, the original pinmux is persistent. So . . . > $ sudo sh -c "echo '-5' > /sys/devices/platform/bone_capemgr/slots" > $ cat /sys/devices/platform/bone_capemgr/slots > 0: PF---- -1 > 1: PF---- -1 > 2: PF---- -1 > 3: PF---- -1 > $ sudo cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins |grep 840 > pin 16 (44e10840.0) 00000017 pinctrl-single > > Ok just as I expected. pinmux's are kept until explicitly changed. Let's try > loading it again. > $ sudo sh -c "echo 'pinctrl-test-7' > > /sys/devices/platform/bone_capemgr/slots" > $ sudo cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins |grep 840 > pin 16 (44e10840.0) 00000017 pinctrl-single > > Whoopsy . . .. > > > > > > On Fri, Nov 27, 2015 at 10:26 PM, William Hermans <[email protected] > <mailto:[email protected]>> wrote: > Here is what I get by following > https://github.com/jadonk/validation-scripts/blob/master/test-capemgr/README.md > > <https://github.com/jadonk/validation-scripts/blob/master/test-capemgr/README.md>, > and modifying it to reflect one of the pins Riley is using. So, what I > suggest is that Riley has an overlay loaded that has already claimed these > pins. Either by experimenting previously with different values, and not > unloading the previous overlay. Or An overlay unbeknownst to him. I'll > experiment now with changing up my overlay and see what happens. But the only > other option really is that something on Riley's system is broken. > > /* > * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ > <http://www.ti.com/> > * > * This program is free software; you can redistribute it and/or modify > * it under the terms of the GNU General Public License version 2 as > * published by the Free Software Foundation. > */ > /dts-v1/; > /plugin/; > > / { > compatible = "ti,beaglebone", "ti,beaglebone-black"; > > /* identification */ > part-number = "pinctrl-test-7"; > > fragment@0 { > target = <&am33xx_pinmux>; > __overlay__ { > pinctrl_test: pinctrl_test_7_pins { > pinctrl-single,pins = < > 0x040 0x17 // P9_15 PINS$16 GPIO1_16 = 48 Input Mode7 > pullup > >; > }; > }; > }; > > fragment@1 { > target = <&ocp>; > __overlay__ { > test_helper: helper { > compatible = "gpio-of-helper"; > pinctrl-names = "default"; > pinctrl-0 = <&pinctrl_test>; > status = "okay"; > }; > }; > }; > }; > > $ dtc -O dtb -o pinctrl-test-7-00A0.dtbo -b 0 -@ pinctrl-test-7.dts > $ sudo cp pinctrl-test-7-00A0.dtbo /lib/firmware/ > $ cat /sys/devices/platform/bone_capemgr/slots > 0: PF---- -1 > 1: PF---- -1 > 2: PF---- -1 > 3: PF---- -1 > $ sudo sh -c "echo 'pinctrl-test-7' > > /sys/devices/platform/bone_capemgr/slots" > $ cat /sys/devices/platform/bone_capemgr/slots > $ cat /sys/devices/platform/bone_capemgr/slots > 0: PF---- -1 > 1: PF---- -1 > 2: PF---- -1 > 3: PF---- -1 > 4: P-O-L- 0 Override Board Name,00A0,Override Manuf,pinctrl-test-7 > $ dmesg |grep pinctrl-test-7 > [168784.685978] bone_capemgr bone_capemgr: part_number 'pinctrl-test-7', > version 'N/A' > [168784.706649] bone_capemgr bone_capemgr: slot #4: 'Override Board > Name,00A0,Override Manuf,pinctrl-test-7' > [168784.723188] bone_capemgr bone_capemgr: slot #4: dtbo > 'pinctrl-test-7-00A0.dtbo' loaded; overlay id #0 > > $ sudo cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins |grep 840 > pin 16 (44e10840.0) 00000017 pinctrl-single > > On Fri, Nov 27, 2015 at 10:14 PM, John Syne <[email protected] > <mailto:[email protected]>> wrote: > I believe the pinmux gets setup in pinctrl_bind_pins() found in > drivers/pinctrl.c. > > pinctrl_bind_pins() gets called by really_probe(), line 291 of drivers/dd.c > and then calls the gpio_of_helper_probe on line 316 or 320, so I don’t think > this has anything to do with gpio-of-helper.c driver. Probably need to setup > some debug statements in pinctrl_bind_pins() to see why this does not work. > > Regards, > John > > > > > > On Nov 27, 2015, at 7:25 PM, Charles Steinkuehler <[email protected] > > <mailto:[email protected]>> wrote: > > > > I don't have time to dig into the full details, but IIRC this has > > popped up before. I don't think the gpio-of-helper driver actually > > does anything (like setup the pinmux) if you're not actually > > _exporting_ any gpios. But I could be wrong...it's been a while since > > I crawled through the code. > > > > Oh, and your pinmux settings don't match the comments. If you really > > want inputs with the pullup enabled, the value to use is 0x37, *NOT* > > 0x17. It's important to enable the gpio receive buffer (bit 0x20) or > > you won't be able to read the value on the GPIO pin (IIRC it will > > always return zero). If you really want outputs and just didn't > > update the comments, 0x17 is fine. > > > > On 11/27/2015 2:14 PM, Riley Porter wrote: > >> Yes I am running: > >> > >> *Linux beaglebone 4.1.1-bone10 #1 Tue Jul 7 01:15:35 UTC 2015 armv7l > >> GNU/Linux* > >> > >> I followed your instructions but still am at a loss. I was able to update > >> the device tree compiler and the kernel which is now: > >> > >> *Linux beaglebone 4.1.13-ti-r33 #1 SMP PREEMPT Fri Nov 20 11:00:50 UTC 2015 > >> armv7l GNU/Linux* > >> > >> Perhaps describing my exact steps might shed some light on my screw up? > >> > >> > >> *This is the device tree I am testing with:* > >> > >> > >> /* > >>> snip for space > >>> */ > >>> /dts-v1/; > >>> /plugin/; > >>> > >>> /{ > >>> compatible = "ti,beaglebone", "ti,beaglebone-black"; > >>> part-number = "EBB-GPIO-Example"; > >>> version = "00A0"; > >>> > >>> fragment@0 { > >>> target = <&am33xx_pinmux>; > >>> > >>> > >>> __overlay__ { > >>> ebb_example: EBB_GPIO_Example { > >>> pinctrl-single,pins = < > >>> > >>> > >>> /*============= Inputs ================*/ > >>> 0x070 0x17 // P9_11 PINS$28 GPIO0_30 = 30 > >>> Input Mode7 pullup > >>> 0x078 0x17 // P9_12 PINS$30 GPIO1_28 = 60 > >>> Input Mode7 pullup > >>> 0x074 0x17 // P9_13 PINS$29 GPIO0_31 = 31 > >>> Input Mode7 pullup > >>> 0x048 0x17 // P9_14 PINS$18 GPIO1_18 = 50 > >>> Input Mode7 pullup > >>> 0x040 0x17 // P9_15 PINS$16 GPIO1_16 = 48 > >>> Input Mode7 pullup > >>> 0x04c 0x17 // P9_16 PINS$19 GPIO1_19 = 51 > >>> Input Mode7 pullup > >>> 0x15c 0x17 // P9_17 PINS$87 GPIO0_5 = 5 > >>> Input Mode7 pullup > >>> 0x158 0x17 // P9_18 PINS$86 GPIO0_4 = 4 > >>> Input Mode7 pullup > >>> > >>> /* OUTPUT GPIO(mode7) 0x07 pulldown, 0x17 > >>> pullup, 0x?f no pullup/down */ > >>> /* INPUT GPIO(mode7) 0x27 pulldown, 0x37 > >>> pullup, 0x?f no pullup/down */ > >>>> ; > >>> }; > >>> }; > >>> }; > >>> > >>> fragment@1 { > >>> target = <&ocp>; > >>> __overlay__ { > >>> gpio_helper { > >>> compatible = "gpio-of-helper"; > >>> status = "okay"; > >>> pinctrl-names = "default"; > >>> pinctrl-0 = <&ebb_example>; > >>> }; > >>> }; > >>> }; > >>> }; > >> > >> > >> > >> I also removed ALL overlays from my system before doing this below. > >> Here is my output from slots and a python program to get the pins i wrote: > >> > >> *root ~/bbb_stuff # **slots* > >> > >> > >> > >> > >> * 0: PF---- -1 1: PF---- -1 2: PF---- -1 3: PF---- -1 9: P-O-L- 0 > >> Override Board Name,00A0,Override Manuf,EBB-GPIO-Example* > >> > >> *root ~/bbb_stuff # ./getpins * > >> > >> > >> > >> *==================================================Reading Pinux > >> Pins==================================================* > >> > >> > >> > >> > >> > >> > >> > >> > >> *pin 16 (44e10840.0) 00000027 pinctrl-singlepin 18 (44e10848.0) 00000027 > >> pinctrl-singlepin 19 (44e1084c.0) 00000027 pinctrl-singlepin 28 > >> (44e10870.0) 00000017 pinctrl-singlepin 29 (44e10874.0) 00000027 > >> pinctrl-singlepin 30 (44e10878.0) 00000027 pinctrl-singlepin 86 > >> (44e10958.0) 00000027 pinctrl-singlepin 87 (44e1095c.0) 00000027 > >> pinctrl-single* > >> > >> You can clearly see I have requested them all to be 0x17? > >> > >> *Here are the alias's I am using:* > >> > >> *pins='cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins'**slots='cat > >> /sys/devices/platform/bone_capemgr/slots'* > >> > >> > >> *This is the command i used to compile the dt.* > >> *dtc -O dtb -o EBB-GPIO-Example-00A0.dtbo -b 0 -@ EBB-GPIO-Example.dts* > >> > >> *This is the command I used to install it:* > >> *echo EBB-GPIO-Example-00A0 > "/sys/devices/platform/bone_capemgr/slots"* > >> > >> > >> *This is the dmesg output after installing the overlay:* > >> > >> > >> > >> > >> > >> > >> *[ 2629.259630] bone_capemgr bone_capemgr: part_number > >> 'EBB-GPIO-Example-00A0', version 'N/A'[ 2629.259679] bone_capemgr > >> bone_capemgr: slot #11: override[ 2629.259700] bone_capemgr bone_capemgr: > >> Using override eeprom data at slot 11[ 2629.259722] bone_capemgr > >> bone_capemgr: slot #11: 'Override Board Name,00A0,Override > >> Manuf,EBB-GPIO-Example'[ 2629.271307] gpio-of-helper ocp:gpio_helper: > >> ready[ 2629.271555] bone_capemgr bone_capemgr: slot #11: dtbo > >> 'EBB-GPIO-Example-00A0.dtbo' loaded; overlay id #0* > >> > >> > >> > >> So any help guys would be really appreciated! I am thinking that I must be > >> just doing something wrong. Perhaps the example device tree I am using is > >> outdated? Would someone be willing to share with me a GPIO device tree > >> that works with kernel 4.1? Also I have tried the dt builder online: > >> > >> http://kilobaser.com/blog/2014-07-28-beaglebone-black-devicetreeoverlay-generator#1gpiodto > >> > >> <http://kilobaser.com/blog/2014-07-28-beaglebone-black-devicetreeoverlay-generator#1gpiodto> > >> > >> But this seems to not work also. Thanks again everyone. > >> > >> > >> Riley > >> > >> On Thu, Nov 26, 2015 at 2:13 PM, John Syne <[email protected] > >> <mailto:[email protected]>> wrote: > >> > >>> That is strange because it seems to be working for everyone else. What is > >>> your kernel version? > >>> > >>> If you are using kernel version 4.1 or higher, then do the following on > >>> your BBB > >>> > >>> git clone https://github.com/RobertCNelson/bb.org-overlays.git > >>> <https://github.com/RobertCNelson/bb.org-overlays.git> > >>> > >>> Follow the instructions readme.md <http://readme.md/> file. My guess is > >>> you don’t have the > >>> correct Device Tree Compiler, but this repo will install the correct > >>> version. > >>> > >>> Regards, > >>> John > >>> > >>> > >>> > >>> > >>> On Nov 26, 2015, at 8:35 AM, Riley Porter <[email protected] > >>> <mailto:[email protected]>> wrote: > >>> > >>> Hey guys, > >>> > >>> I have been fighting this for a few days now. But it seems to me that no > >>> matter what I do I cannot get the pinmux'ing to work when applying > >>> overlays > >>> in debian. I have tried 7.8 and 8.2 and either is really different. > >>> > >>> I was looking around to see if I was the only one in this boat and it > >>> turns out I found a post on stack exchange that describes my issue > >>> perfectly. > >>> > >>> Unfortunately the "answer" was to install angstrom. I was hoping someone > >>> on the list would have some secret answer as to why applying an overlay > >>> was > >>> not changing the pinmux's? > >>> > >>> I would very much like to stick with debian but if the answer is go back > >>> angstrom I guess I can live with that. > >>> > >>> Thanks > >>> > >>> -- > >>> For more options, visit http://beagleboard.org/discuss > >>> <http://beagleboard.org/discuss> > >>> --- > >>> You received this message because you are subscribed to the Google Groups > >>> "BeagleBoard" group. > >>> To unsubscribe from this group and stop receiving emails from it, send an > >>> email to [email protected] > >>> <mailto:beagleboard%[email protected]>. > >>> For more options, visit https://groups.google.com/d/optout > >>> <https://groups.google.com/d/optout>. > >>> > >>> > >>> -- > >>> For more options, visit http://beagleboard.org/discuss > >>> <http://beagleboard.org/discuss> > >>> --- > >>> You received this message because you are subscribed to the Google Groups > >>> "BeagleBoard" group. > >>> To unsubscribe from this group and stop receiving emails from it, send an > >>> email to [email protected] > >>> <mailto:beagleboard%[email protected]>. > >>> For more options, visit https://groups.google.com/d/optout > >>> <https://groups.google.com/d/optout>. > >>> > >> > > > > > > -- > > Charles Steinkuehler > > [email protected] <mailto:[email protected]> > > > > -- > > For more options, visit http://beagleboard.org/discuss > > <http://beagleboard.org/discuss> > > --- > > You received this message because you are subscribed to the Google Groups > > "BeagleBoard" group. > > To unsubscribe from this group and stop receiving emails from it, send an > > email to [email protected] > > <mailto:beagleboard%[email protected]>. > > For more options, visit https://groups.google.com/d/optout > > <https://groups.google.com/d/optout>. > > -- > For more options, visit http://beagleboard.org/discuss > <http://beagleboard.org/discuss> > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected] > <mailto:beagleboard%[email protected]>. > For more options, visit https://groups.google.com/d/optout > <https://groups.google.com/d/optout>. > > > > > > -- > For more options, visit http://beagleboard.org/discuss > <http://beagleboard.org/discuss> > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected] > <mailto:[email protected]>. > For more options, visit https://groups.google.com/d/optout > <https://groups.google.com/d/optout>. -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
