Dear Robert, Thanks a lot for your help! Unfortunately - no luck with both methods with same symptoms
Netinstall. > git clone https://github.com/RobertCNelson/netinstall > cd netinstall > sudo ./mk_mmc.sh --mmc /dev/sdf --dtb omap3-beagle --distro xenial gives ====================== 40W U-Boot SPL 2016.01-00001-g3f205b0 (Mar 01 2016 - 14:23:49) Trying to boot from MMC SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! reading u-boot.img reading u-boot.img U-Boot 2016.01-00001-g3f205b0 (Mar 01 2016 - 14:23:49 -0600), Build: jenkins-github_Bootloader-Builder-337 OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0 *** Warning - bad CRC, using default environment Beagle Rev C4 Timed out in wait_for_event: status=0000 Check if pads/pull-ups of bus 1 are properly configured No EEPROM on expansion board Timed out in wait_for_event: status=0000 Check if pads/pull-ups of bus 1 are properly configured No EEPROM on expansion board OMAP die ID: 1401d01c04037305000000002eaa0004Net: usb_ether Error: usb_ether address not set. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 Checking for: /uEnv.txt ... Checking for: /boot/uEnv.txt ... reading /boot/uEnv.txt 184 bytes read in 4 ms (44.9 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... Running uname_boot ... loading /boot/vmlinuz-current ... reading /boot/vmlinuz-current 5778816 bytes read in 426 ms (12.9 MiB/s) loading /boot/dtbs/current/omap3-beagle.dtb ... reading /boot/dtbs/current/omap3-beagle.dtb 107105 bytes read in 23 ms (4.4 MiB/s) loading /boot/initrd.img-current ... reading /boot/initrd.img-current 58777385 bytes read in 4280 ms (13.1 MiB/s) Installer for [xenial-armhf] is using the Serial Interface debug: [console=ttyO2,115200n8 root=/dev/ram rw musb_hdrc.fifo_mode=5] ... debug: [bootz 0x82000000 0x88080000:380df29 0x88000000] ... Kernel image @ 0x82000000 [ 0x000000 - 0x582d80 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8c7f2000, end 8fffff29 ... ============================================================================== Precompiled image method > wget https://rcn-ee.com/rootfs/2016-02-11/elinux/ubuntu-xenial-console-armhf-2016-02-11.tar.xz > tar xf ubuntu-xenial-console-armhf-2016-02-11.tar.xz > cd ubuntu-xenial-console-armhf-2016-02-11 > sudo ./setup_sdcard.sh --mmc /dev/sdf --dtb omap3-beagle ============================================================================== 40W U-Boot SPL 2016.01-00001-g3f205b0 (Mar 01 2016 - 14:23:49) Trying to boot from MMC SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! reading u-boot.img reading u-boot.img U-Boot 2016.01-00001-g3f205b0 (Mar 01 2016 - 14:23:49 -0600), Build: jenkins-github_Bootloader-Builder-337 OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 MHz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0 *** Warning - bad CRC, using default environment Beagle Rev C4 Timed out in wait_for_event: status=0000 Check if pads/pull-ups of bus 1 are properly configured No EEPROM on expansion board Timed out in wait_for_event: status=0000 Check if pads/pull-ups of bus 1 are properly configured No EEPROM on expansion board OMAP die ID: 1401d01c04037305000000002eaa0004Net: usb_ether Error: usb_ether address not set. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 Checking for: /uEnv.txt ... Checking for: /boot/uEnv.txt ... 295 bytes read in 28 ms (9.8 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt... Running uname_boot ... loading /boot/vmlinuz-4.4.1-armv7-x5 ... 5766104 bytes read in 458 ms (12 MiB/s) loading /boot/dtbs/4.4.1-armv7-x5/omap3-beagle.dtb ... 107105 bytes read in 91 ms (1.1 MiB/s) loading /boot/initrd.img-4.4.1-armv7-x5 ... 16301865 bytes read in 1236 ms (12.6 MiB/s) debug: [console=ttyO2,115200n8 root=UUID=d96b5f18-265e-49be-a8f0-d4be34d1d7f6 ro rootfstype=ext4 rootwait musb_hdrc.fifo_mode=5 coherent_pool=1M quiet] ... debug: [bootz 0x82000000 0x88080000:f8bf29 0x88000000] ... Kernel image @ 0x82000000 [ 0x000000 - 0x57fbd8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8f074000, end 8fffff29 ... ============================================================================== On Sunday, March 6, 2016 at 11:35:21 PM UTC+3, RobertCNelson wrote: > > Or use the net install found here > > https://github.com/RobertCNelson/netinstall > > With the 4.1 LTS kernel option. > > See my last comment here.. > > > https://github.com/RobertCNelson/armv7-multiplatform/issues/25#issuecomment-192494682 > On Mar 6, 2016 2:30 PM, "Robert Nelson" <[email protected] <javascript:>> > wrote: > >> It's the v4.4.x kernel with trusty.. >> >> Use the xenial beta image. >> >> I'm dropping trusty.. >> >> On Mar 6, 2016 2:24 PM, <[email protected] <javascript:>> wrote: >> > >> > Hello, >> > I have issues trying to upgrade the Beagleboard C4 ubuntu. >> > I followed the guide on http://elinux.org/BeagleBoardUbuntu , but >> both Method 1 and Method failed. >> > >> > It seems like it fails in uboot, just before the actual kernel start. >> > Here is a full pastebin: http://pastebin.com/T6nnx1QP >> > >> > And a small end of log: >> > >> > Loaded environment from /boot/uEnv.txt >> > Checking if uname_r is set in /boot/uEnv.txt... >> > Running uname_boot ... >> > loading /boot/vmlinuz-4.4.1-armv7-x5 ... >> > 5699696 bytes read in 452 ms (12 MiB/s) >> > loading /boot/dtbs/4.4.1-armv7-x5/omap3-beagle.dtb ... >> > 107105 bytes read in 153 ms (683.6 KiB/s) >> > loading /boot/initrd.img-4.4.1-armv7-x5 ... >> > 12722954 bytes read in 969 ms (12.5 MiB/s) >> > debug: [console=ttyO2,115200n8 >> root=UUID=4817de6d-b3bb-4fb5-8157-492d5eedb08a ro rootfstype=ext4 rootwait >> musb_hdrc.fifo_mode=5 coherent_pool=1M quiet] ... >> > debug: [bootz 0x82000000 0x88080000:c2230a 0x88000000] ... >> > Kernel image @ 0x82000000 [ 0x000000 - 0x56f870 ] >> > ## Flattened Device Tree blob at 88000000 >> > Booting using the fdt blob at 0x88000000 >> > Loading Ramdisk to 8f3dd000, end 8ffff30a ... >> > >> > >> > After the Ramdisk line - device halts. >> > >> > Additional info: >> > 1. MMC had passed badblocks test - so it should be fine. >> > 2. I have two identical Beagleboards C4 - and both fail in the same >> way. So it should not be hardware issue. >> > 3. Beagleboards are able to run old Ubuntu 9.10 - so again it seem >> to prove they are fine. >> > 4. I have tried "nand erase 260000 20000" >> > >> > Questions - >> > 1. Have anyone a a copy of ubuntu >14.04 that works with Beagleboards >> Ax/Bx/Cx/Dx? Can you please share? >> > 2. Had anyone same issue as above? Google seem to be silent. >> > 3. Any other idea how to proceed? Can old NAND version of uboot >> affect the MMC boot when MMC has a new version of u-boot? >> > >> > Best regards, >> > Alexander >> > >> > -- >> > For more options, visit http://beagleboard.org/discuss >> > --- >> > You received this message because you are subscribed to the Google >> Groups "BeagleBoard" group. >> > To unsubscribe from this group and stop receiving emails from it, send >> an email to [email protected] <javascript:>. >> > For more options, visit https://groups.google.com/d/optout. >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
