On Wed, Jun 15, 2016 at 7:14 AM, <[email protected]> wrote: > Hi, > > I have tried several ways to flash my BBB's eMMC including: > > 1) un-commenting the following line in /boot/uEnv.txt : > #cmdline=init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh > > 2) pushing the S2 button in power-up . > > In both methods nothing happens and it boots on uSD card. The minicom output > is as follows: > > U-Boot SPL 2016.03-00001-gd12d09f (Mar 17 2016 - 16:16:15) > Trying to boot from MMC > bad magic > > > U-Boot 2016.03-00001-gd12d09f (Mar 17 2016 - 16:16:15 -0500), Build: > jenkins-github_Bootloader-Builder-351 > > Watchdog enabled > I2C: ready > DRAM: 512 MiB > Reset Source: Power-on reset has occurred. > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > Using default environment > > Net: <ethaddr> not set. Validating first E-fuse MAC > cpsw, usb_ether > Press SPACE to abort autoboot in 2 seconds > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > gpio: pin 56 (gpio 56) value is 0 > gpio: pin 55 (gpio 55) value is 0 > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 53 (gpio 53) value is 1 > switch to partitions #0, OK > mmc0 is current device > gpio: pin 54 (gpio 54) value is 1 > Checking for: /uEnv.txt ... > 1179 bytes read in 12 ms (95.7 KiB/s) > gpio: pin 55 (gpio 55) value is 1 > Loaded environment from uEnv.txt > Importing environment from mmc ... > Checking if uenvcmd is set ... > gpio: pin 56 (gpio 56) value is 1 > Running uenvcmd ... > 1197 bytes read in 69 ms (16.6 KiB/s) > debug: [/boot/vmlinuz-4.4.9-ti-r25] ... > 7833256 bytes read in 501 ms (14.9 MiB/s) > debug: [/boot/initrd.img-4.4.9-ti-r25] ... > 4761957 bytes read in 321 ms (14.1 MiB/s) > debug: [/boot/dtbs/4.4.9-ti-r25/am335x-boneblack.dtb] ... > 60958 bytes read in 92 ms (646.5 KiB/s) > debug: [console=tty0 console=ttyO0,115200n8 root=/dev/mmcblk0p1 > rootfstype=ext4 rootwait coherent_pool=1M quiet cape_universal=enable] ...
Notice you don't see "init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh" here? That means, you didn't un-comment: #cmdline=init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh -> cmdline=init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh > debug: [bootz 0x82000000 0x88080000:48a965 0x88000000] ... > Kernel image @ 0x82000000 [ 0x000000 - 0x7786a8 ] > ## Flattened Device Tree blob at 88000000 > Booting using the fdt blob at 0x88000000 > Using Device Tree in place at 88000000, end 88011e1d > > Starting kernel ... > > [ 2.006623] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle > [ 2.177466] omap_voltage_late_init: Voltage driver support not added > [ 2.184898] PM: Cannot get wkup_m3_ipc handle > [ 2.293317] bone_capemgr bone_capemgr: slot #0: No cape found > [ 2.337340] bone_capemgr bone_capemgr: slot #1: No cape found > [ 2.381298] bone_capemgr bone_capemgr: slot #2: No cape found > [ 2.425306] bone_capemgr bone_capemgr: slot #3: No cape found > Loading, please wait... > fsck: error 2 (No such file or directory) while executing fsck.ext4 for > /dev/mmcblk0p1 > fsck exited with status code 8 > [ 10.416490] systemd-fsck[158]: rootfs: clean, 137855/217728 files, > 813740/870144 blocks > [ 17.392524] remoteproc1: failed to load am335x-pru0-fw > [ 17.529704] remoteproc1: request_firmware failed: -2 > [ 17.534990] pru-rproc 4a334000.pru0: rproc_boot failed > [ 18.040100] remoteproc1: failed to load am335x-pru1-fw > [ 18.081632] remoteproc1: request_firmware failed: -2 > [ 18.086946] pru-rproc 4a338000.pru1: rproc_boot failed > [ 21.591446] platform 48300180.eqep: Cannot lookup hwmod 'eqep0' > [ 21.642885] platform 48302180.eqep: Cannot lookup hwmod 'eqep1' > [ 21.691230] platform 48304180.eqep: Cannot lookup hwmod 'eqep2' > [ 22.556778] eqep 48300180.eqep: failed to get clock > [ 22.778073] eqep 48302180.eqep: failed to get clock > [ 23.112100] eqep 48304180.eqep: failed to get clock > > Debian GNU/Linux 8 beaglebone ttyS0 > > BeagleBoard.org Debian Image 2016-05-13 > > Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian > > default username:password is [debian:temppwd] > > The IP Address for usb0 is: 192.168.7.2 > beaglebone login: > > > > > when I run "lsblk" on my BBB it outputs like this: > > mmcblk1boot0 179:16 0 1M 1 disk > mmcblk1boot1 179:24 0 1M 1 disk > mmcblk0 179:0 0 3.7G 0 disk > ����─mmcblk0p1 179:1 0 3.3G 0 part / > mmcblk1 179:8 0 1.8G 0 disk > ��└��─mmcblk1p1 179:9 0 1.8G 0 part > > > which shows that eMMC storage is 1.8G. very surprised! > > don't know where to go from here! PS, you have a 2gb bbb, use the 2gb images, as teh 4gb won't fit. Regards, -- Robert Nelson https://rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAOCHtYjNkA79pUZaEMhY-nNouGJVXs449u-vqM-uLQ8z2QGNPA%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.
