Additional information if this helps. P9.42 if I recall is one of the pins
that are tied together for mmc_cmd ? So, kind of has my attention.
/* state the resources this cape uses */
exclusive-use =
/* the pin header uses */
"P8.8",
"P8.9",
"P8.10",
"P8.11",
"P8.12",
"P8.13", /* EHRPWM2B */
"P8.13",
"P8.14",
"P8.15",
"P8.16",
"P8.17",
"P8.18",
"P8.19", /* EHRPWM2A */
"P8.26",
"P8.27",
"P9.11", /* UART4_RX */
"P9.12",
"P9.13", /* UART4_TX */
"P9.14", /* EHRPWM1A */
"P9.15",
"P9.16", /* EHRPWM1B */
"P9.21", /* EHRPWM0A */
"P9.22", /* EHRPWM0B */
"P9.23",
"P9.25",
"P9.27",
"P9.28",
"P9.29",
"P9.30",
"P9.31",
*"P9.42",*
/* the hardware ip uses */
"uart4",
"ehrpwm0A",
"ehrpwm0B",
"ehrpwm1A",
"ehrpwm1B",
"ehrpwm2A",
"ehrpwm2B";
On Wed, Oct 12, 2016 at 6:37 PM, William Hermans <[email protected]> wrote:
> By the way, this has been tested consistently on one BBB RevC, and
> several( tens ) of BBG's. By me personally, and another person, elsewhere.
>
> On Wed, Oct 12, 2016 at 6:33 PM, William Hermans <[email protected]>
> wrote:
>
>> So I've been searching the groups here for the last several hours. I've
>> tried several things, even noted that the device tree "binary" file
>> (compiled file in /lib/firmware) was marked as executable. So I set the
>> executable bit via chmod -x . . .Anyway, this is a custom device tree
>> overlay binary, that enabled several GPO's 6 GPI's, and all 3 "dual
>> channel" pwm modules. Plus I think uart4. The overlay fails to load at boot
>> via /boot/uEnv.txt.
>>
>> william@beaglebone:~$ dmesg |grep controller
>> [ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8
>> bone_capemgr.enable_partno=controller root=/dev/mmcblk0p1 rootfstype=ext4
>> rootwait coherent_pool=1M quiet cape_universal=enable ipv6.disable=1
>> . . .
>> [ 2.167008] IPv6: Loaded, but administratively disabled, reboot
>> required to enable
>> [ 2.426546] bone_capemgr bone_capemgr: enabled_partno PARTNO
>> 'lcontroller' VER 'N/A' PR '0'
>> [ 2.426586] bone_capemgr bone_capemgr: slot #4: 'Override Board
>> Name,00A0,Override Manuf,controller'
>> [ 3.437016] bone_capemgr bone_capemgr: loader: failed to load slot-4
>> controller:00A0 (prio 0)
>>
>>
>>
>> I have tried this with cape_universal=enable, as well as commented out(
>> simply removed the text ).
>>
>> william@beaglebone:~$ uname -r
>> 4.4.14-ti-r34
>> william@beaglebone:~$ cat /etc/dogtag
>> BeagleBoard.org Debian Image 2016-05-01
>> william@beaglebone:~$ dtc -v
>> Version: DTC 1.4.1
>>
>> So here is the funny part.
>>
>> william@beaglebone:~$ sudo config-pin overlay controller
>> [sudo] password for william:
>> Loading led-controller overlay
>>
>> william@beaglebone:~$ dmesg |grep controller
>> [ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8
>> bone_capemgr.enable_partno=controller root=/dev/mmcblk0p1 rootfstype=ext4
>> rootwait coherent_pool=1M quiet cape_universal=enable ipv6.disable=1
>> [ 2.426546] bone_capemgr bone_capemgr: enabled_partno PARTNO
>> 'controller' VER 'N/A' PR '0'
>> [ 2.426586] bone_capemgr bone_capemgr: slot #4: 'Override Board
>> Name,00A0,Override Manuf,controller'
>> [ 3.437016] bone_capemgr bone_capemgr: loader: failed to load slot-4
>> controller:00A0 (prio 0)
>> [ 1972.395048] bone_capemgr bone_capemgr: part_number 'controller',
>> version 'N/A'
>> [ 1972.395115] bone_capemgr bone_capemgr: slot #5: 'Override Board
>> Name,00A0,Override Manuf,controller'
>> [ 1972.526297] bone_capemgr bone_capemgr: slot #5: dtbo
>> 'controller-00A0.dtbo' loaded; overlay id #0
>>
>>
>>
>> Is this a known issue ? Or maybe I'm doing something wrong ? Maybe I need
>> a different board file loaded at boot ?
>>
>> william@beaglebone:~$ cat /boot/uEnv.txt
>> #Docs: http://elinux.org/Beagleboard:U-boot_partitioning_layout_2.0
>>
>> uname_r=4.4.14-ti-r34
>> #uuid=
>> #dtb=
>>
>> ##BeagleBone Black/Green dtb's for v4.1.x (BeagleBone White just works..)
>>
>> ##BeagleBone Black: HDMI (Audio/Video) disabled:
>> dtb=am335x-boneblack-emmc-overlay.dtb
>>
>> ##BeagleBone Black: eMMC disabled:
>> #dtb=am335x-boneblack-hdmi-overlay.dtb
>>
>> ##BeagleBone Black: HDMI Audio/eMMC disabled:
>> #dtb=am335x-boneblack-nhdmi-overlay.dtb
>>
>> ##BeagleBone Black: HDMI (Audio/Video)/eMMC disabled:
>> #dtb=am335x-boneblack-overlay.dtb
>>
>> ##BeagleBone Black: wl1835
>> #dtb=am335x-boneblack-wl1835mod.dtb
>>
>> ##BeagleBone Green: eMMC disabled
>> #dtb=am335x-bonegreen-overlay.dtb
>>
>> cmdline=coherent_pool=1M quiet cape_universal=enable ipv6.disable=1
>> #cmdline=ipv6.disable=1 quiet
>>
>> #In the event of edid real failures, uncomment this next line:
>> #cmdline=coherent_pool=1M quiet cape_universal=enable
>> video=HDMI-A-1:1024x768@60e
>>
>> ##Example v3.8.x
>> #cape_disable=capemgr.disable_partno=
>> #cape_enable=capemgr.enable_partno=
>>
>> ##Example v4.1.x
>> #cape_disable=bone_capemgr.disable_partno=
>> cape_enable=bone_capemgr.enable_partno=controller
>>
>> ##enable Generic eMMC Flasher:
>> ##make sure, these tools are installed: dosfstools rsync
>> #cmdline=init=/opt/scripts/tools/eMMC/init-eMMC-flasher-v3.sh
>>
>>
>> william@beaglebone:~$ cat /sys/devices/platform/bone_capemgr/slots
>> 0: PF---- -1
>> 1: PF---- -1
>> 2: PF---- -1
>> 3: PF---- -1
>> 5: P-O-L- 0 Override Board Name,00A0,Override Manuf,controller
>>
>>
>>
>> The overlay source file does have some aspects similar to the universal
>> IO overlays. dir-changable, init-hi/lo etc.
>>
>>
>>
>> --
>> For more options, visit http://beagleboard.org/discuss
>> ---
>> You received this message because you are subscribed to the Google Groups
>> "BeagleBoard" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected].
>> To view this discussion on the web visit https://groups.google.com/d/ms
>> gid/beagleboard/408d8389-6999-4d06-8b60-21795c240e92%40googlegroups.com
>> <https://groups.google.com/d/msgid/beagleboard/408d8389-6999-4d06-8b60-21795c240e92%40googlegroups.com?utm_medium=email&utm_source=footer>
>> .
>> For more options, visit https://groups.google.com/d/optout.
>>
>
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/CALHSORocg8wFy9mXdn8jxiWwCf22HEM%3Dqj4VJM9pyPkr%2Bk08WQ%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.
